極限變形 的英文怎麼說
中文拼音 [jíxiànbiànxíng]
極限變形
英文
limit deformation-
The current chinese foundation design code gbj7 - 89 use limit equilibrium theoiy with elastic soil stress distribution to give out bearing capacity design value calculating fonnula and use elastic soil model to evaluate foundation settlement. according to the above theories, code gbj7 - 89 gives the correlative terms. but these do not accord with the practical mechanism of loaded soil below the shallow foundation and the elastoplastic property of natural soil so defects exist
我國現行規范gbj7 - 89將這兩者分開考慮，其計算地基承載力設計值的公式是根據彈性地基中應力分佈及土的極限平衡狀態理論為依據而得出的，求地基的沉降變形時則視土體為彈性，這些理論對地基及土的假設與淺基礎地基的實際工作狀態及天然土體的非線性、彈塑性存在一定的偏差。Establishing an human spine dynamic model is an significan event to study spine injured biomechanics of pilot " s ejective injury, parachute opening, landing and study the endurance to impact loading on human spine. in this paper, the huston " s method of kane " s equations is developed so that it can be applied to the multibodysystem including translation between the bodyies. the dynamic model of human spine is provided basing on these theories, while the big movement of spine is considered. the deformation of vetebra is far smaller comparing with the intervetebra disc, so the spine is considered into multibodysystem including rigid bodies ( vetebra ) and the flexible bodies ( intervetebra disc ). the computer solution correspond with the results of the large scale human impact test. the rigid coefficient factors and the damping factor of intervetebra joints are obtained
人體脊柱動力學模型的建立對研究飛行員彈射救生、傘兵跳傘開傘、著陸等脊柱損傷的生物力學以及研究人體脊柱耐受沖擊載荷的極限問題都具有重要意義.首先發展了凱恩方程的休斯頓方法，使其可應用於變形體連接的多體系統，並以此理論為依據建立人體整椎脊柱沖擊動力學模型，此時考慮脊柱的大位移運動，每個椎骨的變形相對椎間盤的變形小得多，把脊柱看成由剛體（椎骨）和變形體（椎間盤）組成的多體系統.並以大型真人坐姿沖擊實驗結果進行了擬合，最後得到腰椎間關節剛度系數因子和阻尼系數因子The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly
研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。Based on extensive investigation of construction technique history of chinese ancient buildings, the structure method, structure developing history and seismic behavior of chinese ancient timber structure buildings are analyzed in several respects of the structural system and form. through a series of experiments on constituent parts of chinese ancient timber building structure, including the tests on the corbels and brackets called dougong subjected to low cyclic reversed loadings, the tests on the wooden frame using the tenon - mortise joints as connections of column and beam subjected to low cyclic reversed loadings, the tests on vibration isolation effect of friction and slippage between column footing and their socle base, and a series of shaking table tests on a chinese ancient timber structure palace building mode under artificial earthquake at serving conditions, destroyed conditions and reinforced conditions, many valuable results of structures such as moment - curvature hysteretic loops of dougong structure and tenon - mortise joints under low cyckc reversed loadings, the static function, the seismic performance, energy dissipation, vibration reduction, energy - loss mechanism, nechanicalmode and failure mode were studied. aplenty of valuable parameters of the structure system were obtained, such as the natural period of structure, vibration modes, damping ratio, factor of vibration isolation, oscillate amplitude of ineitial accebration, velocity and displacement, magnitude of slippage, and the mechanism of structure failure and collapse etc. based on these research, the complete analysis of ancient timber structure under earthquake were carried out in which including mechanism analysis method, calculating mode, strength analysis of members and joints, strengthening methods for serving damaged ancient timber structure buildings were also taken into account
依照宋代《營造法式》建造了抬梁式殿堂木結構構件及結構模型，對中國古代木結構中的典型構造如：柱腳在礎石頂面平擱簡支、柱架榫卯連接、柱高不越間之廣、側腳、生起、斗拱等的構造機理及結構功能進行了量化分析和實驗研究： （一）通過木柱石礎靜摩擦試驗，測定了柱腳與石礎古鏡面間的摩擦系數及摩擦力隨上部結構荷載變化的規律； （二）通過單柱承載力試驗，測定了古建築中木柱的受力變形特徵、破壞模式、及模型材料的變形模量、極限承載力、極限變形等參量； （三）通過柱架低周反復荷載試驗，測定了柱架的抗側移剛度、柱架恢復力特性及滯回曲線、榫卯張角剛度及其變化規律、柱架及榫卯的極限承載力和極限變形、及榫卯減振參數； （四）通過斗?低周反復荷載試驗和受壓試驗，測定了古建築木構件與木構件間摩擦系數，斗?抗側移剛度，斗?恢復力特性及滯回曲線，斗?抗壓極限承載力及受力變形規律； （五）通過抬梁式殿堂間架模型振動臺試驗，測定了殿堂木構架結構自振周期，地震反應振形、阻尼特性及阻尼比；按結構分層特點對柱腳、柱頭和斗?層上的屋蓋的地震反應採用多點同步測量，對柱根滑移、榫卯變形、斗?的變形、復位、耗能減振參數等進行了定量分析。Based on the destructive test of certain old pre - stressed concrete hollow slab after structural strengthening by cfs, the destructive mechanism and ultimate bearing capacity of old pre - stressed hollow slab after structural strengthening is being researched, which is useful for the strengthening design of old bridge and solvating of single slab problem
摘要通過某已使用10年的舊橋預應力混凝土空心板受拉區碳纖維布加固后的破壞荷載試驗研究，對受拉區加固后的舊橋預應力混凝土空心板的破壞機理、變形性能及極限承載能力等進行了研究，為舊橋預應力混凝土空心板的加固設計及單板受力問題的分析解決提供了試驗依據。This thesis briefly analyzes some yield criteria and instability criteria to the sheet metal forming first. then according to the transformation rule from ultimate strain to ultimate stress, it establishes the mathematical calculation models of the forming limit stress diagram for the software development according to hill48 、 hill79 and hosford yield criterion irrespectively
本文首先分析了板料成形的屈服準則和失穩準則，然後根據極限應變到極限應力的轉換關系，分別採用hill48屈服準則、 hill79屈服準則和hosford屈服準則，建立了用於軟體開發的成形極限應力圖的數學計算模型。The study in the paper starts with beam distortions, and it treats the plastic deformation area as pure bending sect, rest of the beam as rigid bodies. according to different shapes of the external tendons, it divides into three structural forms familiar in projects, that is the beams with no deviator, with a deviator and with two deviators, and studies the relation between the deformation of the external prestressing tendons and that of the beams, and derives the formulas of the ultimate stress increment of external tendons. in the formulas, the ultimate angle corresponding to half of the plastic deformation area is considered as a variable parameter
本文首先從梁極限狀態下的變形入手，將塑性鉸區看作純彎段，將塑性鉸以外的區域看作剛體，按照體外預應力筋的形狀不同，分工程中最常見的三種體外結構形式，即無轉向塊的直線型體外筋混凝土梁、具有一個轉向塊的單折線型梁和具有兩個轉向塊的雙折線型梁，研究體外預應力筋變形和梁體的變形間的關系，推導出以極限狀態下塑性鉸區之半對應的轉角為參數的計算體外預應力混凝土簡支梁以及連續梁的體外筋應力增量計算公式，並進一步求得梁的極限承載力。The deformation of the waffle slab can be calcu1ated by using the tab1es of two - - way so1id s1ab. but with a changing flexural rigidity coefficient, which was very c1ose to the test va1ue in the uncracked and cracked stages
根據試驗結果，用極限平衡法可以便捷和較為準確地求得雙向密肋樓蓋的極限平衡荷載；提出了利用雙向板表格計算雙向密肋樓蓋的變形。It analyse the stability with numerical simulation. finally, on the basis of geological estimation and analysis of the monitoring data and the numerical simulation, it conclude : ( 1 ) through the tracking investigation of the deformation phenomenon, and the study of the rock mass constructure of the slop, it determine the mode of the formation and destruction on the basis of aggregate analysis of the monitoring data
最後，結合地質判斷、監測分析結果及數值模擬分析結果以及對典型剖面的極限平衡計算結果，得出了以下主要成果： （ 1 ）通過對「左砂」邊坡變形破壞跡象的跟蹤調研，對斜坡的巖體結構和已經發生的破壞跡象進行深入的研究分析，結合對監測資料的綜合分析，確定了「左砂」邊坡可能的變形破壞模式。The thickness varies according to the half - apex angle, and the forming limit half - apex angle is the key which nc incremental sheet metal parts forming process succeeds, it relates to the material and thickness of the sheet metal
變形區厚度的變化與成形半頂角有關，其中，成形極限半頂角是數控漸進成形能否成功的關鍵，它不僅與材料有關，而且與板料厚度有關。The conclusion of reappearing analysis is that crane bridge be used as usual because main weld maximum stress of upper cover plate of main beam lower than yield limit though it higher than permissible stress. inner stress of secondary beam was over ultimate strength, and deforming is ultra big. so it was unfit for produce and secondary beam must be changed
再現分析得出的主要結論為：橋架的主樑上蓋板主焊縫的最大應力超過了許用應力，但小於屈服極限，可以繼續投入使用；副梁內部的應力遠遠超過了強度極限，變形特別嚴重，不能滿足生產要求，因此更換新的副梁；端梁內部的應力超過了屈服極限，小於強度極限，在應力較大的位置焊接補強板；投入使用后，要對整個橋架進行定期檢查。The vector magnetic potential of a system consisting a line electric current and an infinite long magnetic dielectric column is calculated with the method of separation of variables and method of images, it is pionted out that the vector magnetic potential of a system consisting a line electric current and a magnetic dielectric plane, an ideal paramagnetic column, a superconductor column, and a line electric current in homogeneous magnetic field can all be deduced from our calculation
摘要用鏡象電流法和分離變量法計算了線電流與無限長磁介質圓柱系統的磁矢勢，指出線電流與無限大磁介質分界平面、線電流與超導體圓柱、均勻外磁場中有磁介質圓柱系統時的磁矢勢都可以由線電流與磁介質圓柱系統的磁矢勢的極限情形給出。By using the bifurcation theory of planar dynamical systems and the method of detection functions, this paper gives a configuration of limit cycles forming compound eyes. with the help of numerical analysis ( using maple ), it is shown that there exist parameter groups such that a polynomial vector field of degree 7 has at least 49 limit cycles with z8 - symmetry
然後，利用平面動力系統的分支理論以及判定函數法，考慮z _ 8 -等變的擾動hamilton向量場，在計算機數學軟體（ maple ）的幫助下，我們得到結論： 8次平面向量場至少有49個極限環，形成具有z _ 8 -對稱性的極限環分佈。According to the basis relation of stress, strain and the value of limit deformation during the strengthening of concrete architecture, the derivate computing method is applied under different state of load and internal force. and it is towards difference of stress and strain of the new and old part of the strengthening structure. it is pointed out that unloading is the necessary and important method of taking advantage of effect of the strengthening structure
本文根據混凝土結構加固中材料的基本應力? ?應變關系和極限變形值，針對加固結構新舊兩部分的應力、應變差，應用迭加原理，導出了加固結構在不同受力狀態下的承載力和內力適用設計計算方法，指出了「卸荷」是充分發揮加固結構效能的必不可少的重要手段。This paper has put forward such one, i. e. to use the dimensional angle iron framework to strengthen the center of the knot in order to add its degree of toughness and stiffness, improve its crack load and aggrandize its ultimate deformation
本文提出了一種提高節點抗震性能的新方法? ?用空間角鋼骨架對節點核心區進行加強，以增大節點的強度、剛度，提高節點的抗剪、抗裂性能，並增大節點的極限變形能力及延性性能。Plastic limited deformation analysis of the clamped rectangular steel plate subjected to air non - contact explosions
空爆載荷作用下固支矩形鋼板的塑性極限變形In the fourth part, by using the bifurcation theory of planar dynamical systems and the method of detection functions, the paper gives a configuration of limit cycles forming compound eyes. with the help of numerical analysis ( usi ng maple ), it is shown that there exist parameter groups such that a z7 - equivariant planar polynomial vector field of degree 7 has at least 36 limit cycles with z7 - symmetry
然後，對於一組特定的參數值，研究了它的相軌線的變化趨勢；第四部分指出：在一定的條件下，利用平面動力系統分支理論以及判定函數法，在計算機數學軟體（ maple ）的幫助下，得到結論： 7次z _ 7 -等變平面向量場至少有36個極限環，形成具有z _ 7 ?對稱性的極限環分佈。Based on the fast freeze - thaw test, the alkaline test, the water immersion test and the wet - thermal test of frp, the influence on frp mechanics behavior caused by aggressive environments are studied, and the causes of degradation of frp behavior are simply analyzed. 5
試驗研究了工程中常用的碳纖維片材和玻璃纖維片材在水環境、濕熱環境、凍融環境、堿化環境下的抗拉強度、彈性模量、極限變形的變化，簡單分析各種環境對復合材料性能影響的原因。The researching aim of this paper is using push - over method to research the elastic - plastic ultimate deformation of self - combusted gangue reinforced concrete ( sgrc ) frame
本文的研究目的是使用靜力彈塑性分析方法（ push - over方法）研究煤矸石混凝土框架的彈塑性極限變形問題。Theory research on the maximum reduction of deep tine taper hole formed by open - die cold extrusion
深小錐孔擠壓成形極限變形程度理論判據建立分享友人