槽型圖 的英文怎麼說
中文拼音 [cáoxíngtú]
槽型圖
英文
profile of groove-
The three - dimensional topography figures of major typical hydrothermal regions are drawn on the basis of field - measured bathymetric data of the okinawa trough and collecting a large number of data on bathymetry, multibeam and seismic profiles of other major typical hydrothermal regions
在沖繩海槽熱液活動區實測水深資料的基礎上，廣泛收集了其他典型熱液活動區的水深、多波束、地震剖面等資料，據此繪制出主要典型熱液活動區的三維地形圖。Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle
流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。Linear induction motor is an important kind of machines which have some merits such as simple structure, low cost, durability, convenience for maintenance etc. the subject of this thesis is to study a big circular ring linear induction motor, and the major works in this thesis are summarized as follows : ( 1 ) considering the effects of the finite length of primary core, one - dimension analytical solution for the air gap field is cited in this paper. based on it, the single layer winding magnetic field is studied. considering whole - pitched and short - pitched winding configuration with odd poles and half - fulled slots in both ends, the double - layer winding magnetic field is analyzed, respectively
本文對大圓環直線感應電機進行了深入細致研究，內容包括： （ 1 ）本文採用有限長行波面電流作用於有限長鐵芯上的模型，引用了氣隙磁場一維解，研究了單層繞組磁場，奇數極半填槽雙層繞組在採用整距和短距時磁場的分析、比較，簡單介紹了二維解； （ 2 ）用有限元軟體ansoft對大圓環直線感應電機空載氣隙磁場進行了靜態分析，並分析了結果； （ 3 ）用軟體進行了額定電壓下的瞬態分析，得到了轉矩，位移，轉速隨時間變化曲線圖，利用單極性霍爾元件測定轉速並與軟體計算結果進行了比較，採用等效電路法計算了堵轉時的最大電磁力並做實驗進行了驗證，由實驗測得了三相電流波形，並與計算結果進行了比較，對其不對稱性進行了定性分析。In this paper, a high integrated and intelligent digital dsp - spm system is developed based on the nspm6800 spm manufactured by the beijing zhongke mechanical & electrical equipment co. at present, the pc of spm system is burdened with not only sending and receiving data, but also disposing of image, which hinders the enhancement of speed of the system. in addition, as the function of spm is expanding, including tappingmode afm, efm, mfm, scm, etc, one hand, it amplifies the range of the application of spm, on the other hand it also means that the task of autocontrol and data transfer heavier. the advantages offered by the dsp compared to analog systems include considerable flexibility in the choice of the signal processing algorithm and greater ease in managing control parameters by the host computer, which are very important for the improvement of spm
本課題以北京市中科機電設備公司的nspm - 6800型掃描探針顯微鏡為基礎，重新設計了以dsp為控制核心的控制系統，主要解決原系統存在的以下問題： （ 1 ） pc機既要實時控制數據的採集與發送，又要進行圖像的后處理，整個系統的實時性難以達到要求； （ 2 ）隨著spm功能的擴展，一方面包括輕敲式原子力顯微鏡、電場力、磁場力、掃描容場顯微鏡等技術在內的spm技術擴展了儀器的測試范圍和功能，另一方面也意味著自動控制量的增加和數據處理量的增加； （ 3 ） 16位a d 、 d a都採用的是購買的板卡，也通過isa槽插在pc機內，成本高，不利於擴展； （ 4 ）另外，數字板通過isa槽插在pc機內，易受于擾，而且給安裝帶來不便。Several types of curved subsoiler shapes are designed and founded, and the macroscopical disturbing profile of soil after subsoiling and these subsoilers ' working resistance are measured with a big laboratory soil bin, the manner of graphics expression about the macroscopical disturbing profile of soil after subsoiling is quantificationally given, and the relation between the cultivation resistance and the macroscopical disturbing profile of soil after subsoiling is analyzed
摘要設計製作了幾種彎曲型深松部件，通過室內大型土槽耕作試驗，測定了各種深松部件耕作以後土壤的宏觀擾動輪廓和耕作阻力，對于土壤的宏觀擾動輪廓給出了定量化的圖形表達方式，並且分析了其與耕作阻力之間的關系。Ys for customers with the provided designation and dimensions of inner holes, key way and width ; also we provide service for the measuring and drawing ofpul
戶提供的規格型號帶輪內孔鍵槽寬度等尺寸為用戶繪制帶輪圖紙也可為用戶提供測繪分享友人