槽寬 的英文怎麼說

In order to reduce the re - deposit volume of the dredged channel, the method must be based on decreasing the oncoming sediment, changing the mouth site, builting the sediment control dam and raising the reservoir level

為了最大限度地減小疏浚挖槽的回淤量，必須依靠控制上游來沙量、調整入水口門位置、加設防淤堤及提高庫水位等手段，而不能通過調整挖泥槽寬度、位置及數量等措施來達到目的。

That machine uses the different siot form to whet the round, can whet a side of straight line or the duckbill sides, the giass of different thicknesschooses to use the different to compiplete, process speed can adjust

該機使用不同的槽形磨輪，可磨直線圓邊或鴨嘴邊，不同厚度的玻璃選用不同槽寬的磨輪，集粗磨、精磨、拋光一次性完成，加工速度可調。

Templates for lettering and symbols. part 2 : slot widths for wood - cased pencils, clutch pencils and fine - lead pencils

書寫字母和符號用模板.第2部分:木質外體鉛筆，鐵桿活動鉛筆和細鉛鉛筆模型槽寬

Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece

將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義

Apace width half angle

槽寬半形

Inner slot width

小端槽寬

Square and rectangular keys and keyways - width tolerances and deviations greater than basic size

方形和矩形鍵和鍵槽.寬度公差和大於基本尺寸的偏差

Normal space - width taper

正常齒槽寬收縮

Mean slot width

中點齒槽寬

Wide drop center rim wd

深槽寬輪輞

The width of main channel would influence the water level rising rate greatly in flood events. when the discharges in main channel increased to 8000 m ' / s from 3000 m3 / s the water rising amplitude at hydrometer stations in the lower yellow river was correlative well with the exponent ( - 0. 65 ) of main channel width and the exponent ( - 0. 33 ) of river longitudinal slope

洪水期主槽寬度對水位漲率有較大影響，主槽流量從3000m ~ 3 s增大到8000m ~ 3 s時，下游各水文站斷面水位的抬升幅度與主槽寬度的（ - 0 . 65 ）次方和河道縱比降的（ - 0 . 33 ）次方具有較好的相關關系。

Compared w ith t he c alculated r esults and monitoring data, to verify i f the p resent parameters can accord with the real situation of nanjing. the distribution of surface settlement trough is obtained by one - dimensional wave theory and calculation. the range of surface settlement trough coefficient is retrofitted

通過對比peck法計算值和實測值，驗證現有的經驗參數是否能很好地滿足南京地區的實際情況，通過對實測曲線的擬合和數值計算得到沉降槽半寬度，從而改進了南京地區橫向地表沉降槽寬度系數k的取值范圍，有助於盾構法在南京地區的推廣和應用。

Then the ideal models ( dielectric isolation structure with high - voltage interconnection and without high - voltage interconnection ) are simulated by a 2d device simulator medici respectively. according to the simulation results, the two models ’ breakdown mechanism is analyzed and compared, and the influence of the isolated trench structure parameter on breakdown - voltage is studied, synchronously

藉助二維數值模擬軟體medici對理想模型（有、無高壓互連線兩種情況的介質隔離結構）進行模擬，分析其耐壓機理，研究隔離槽參數（槽寬、槽內氧化層厚度）對擊穿電壓的影響。

Transverse space - width taper

端面槽寬收縮

Screws. slotted " poelier " head. symbol rl s

螺釘.有槽寬園形頭螺釘.符號rl s

Minimum slot width

最小槽寬

Slot - width taper

槽寬收縮

Outer slot width

大端槽寬

T trough wide

T形槽寬

Width of line slot

線槽寬度規格：