槽形截面 的英文怎麼說
中文拼音 [cáoxíngjiémiàn]
槽形截面
英文
cha elsection-
Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle
流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling
依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。Drilled holes and screw connections for busbars ; channel section busbars
匯流條用鉆孔和螺紋連接件.槽形截面匯流條Agricultural machinery. endless hexagonal belts and groove sections of corresponding pulleys
農業機械.環形六角皮帶和皮帶輪槽形截面Abstract : it was deduced that the shapes of magnetic particle indicationsof point - type defects on workpiece surface depended on the resistance of carrier medium, and their dimensions depended on the volume of the defect equivalent cuboid, the magnetising characters of workpieces and magnetic particles, the strength of magnetic field, the lengths and sections of magnetic particles and the resistance character of carrier medium
文摘:推斷出工件表面點狀缺陷磁痕的形狀取決于磁粉載體的介質阻尼力，磁痕大小取決于缺陷等效長方槽的體積、工件和磁粉材料的磁化特性、磁場強度、磁粉長度和橫截面積以及載體介質的阻尼特性等。Hydraulic fluid power - cylinders - housing dimensions forrectangular - sect bearing rings for pistons and rods
液壓動力.汽缸.活塞及連桿用矩形截面軸承環溝槽尺寸Endless hexagonal belts for agricultural machinery and groove sections of corresponding pulleys
農業機械用的環形六角皮帶及皮帶輪的槽截面Simplified theories are also presented for curved beams with commonly used sections, such as i - shape, channel and h section without any symmetrical axis. linear analysis is also performed in combination with finite element method
其後就常見的截面形式（單軸對稱工字形、槽形和無對稱軸的形截面） ，對所提出的曲梁理論進行簡化，並結合有限元方法求解曲梁的線性問題。分享友人