槽截面 的英文怎麼說

中文拼音 [cáojiémiàn]
槽截面 英文
slot cross section
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  1. Application of elastic variable - section pressure - equalizing groove in the structural design of high - stiffness aerostatic thrust bearing

    用可變截面均壓槽實現高剛度空氣靜壓軸承的結構設計
  2. Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle

    流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。
  3. 2 ) the structure elements should be laid out symmetrically and uniformly when designing steeve - arch structure, what ' s more, the reasonable selection of section geometric size near the arch foots of first beams is paid attention to and the arrangement difficulties of steel bar due to the big eccentric pressures 2, the analyses of anti - seismic features on transverse direction of the aqueduct l ) the method of adjusting the elements " mass can be harnessed in order to even the layout of seismic loads

    2 ）設計吊桿式拱架支承結構時，各部分構件應當均勻對稱布置。另外，還應注意頭道梁拱腳附近截面的尺寸擬定，克服地震內力造成的大偏心受壓狀態給結構配筋設計增加的困難。 2 、橫槽向抗震性能分析1 ）可利用調整構件質量的方法，使得結構的某些構件的地震荷載分佈均勻一些。
  4. On the contents of two sides abovementined, this paper attempts to do some initial researches from three angles as follows : 1, the analyses of anti - seismic features on longitudinal direction of the aqueduct l ) the seismic longitudinal effects are small. the vibrant characters are decided from the structure integration and rigidness of piers and main arch - ring of the aqueduct, so the following measures should be taken in order to weaken and isolate seismic influence : properly broadening the section sizes and adopting the high class concrete, lowering the height and barycenter of building, setting hoop steel bars so as to increase the plasticity of the concrete which can absorb the seismic energy and prevent the damages due to stress centralization on the linkages and changing place

    本文試圖就上述的這兩大方面的內容，從以下三個角度進行了初步研究： 1 、縱槽向抗震性能分析1 ）湯峪河吊桿拱支承結構的縱槽向地震效應較小；吊桿式拱架結構動力特性取決于槽墩和主拱圈的剛度，以及結構的整體性，故適當加大構件截面尺寸或提高砼標號，盡量降低結構的建築高度和重心，在構件連接和變截面處增設梗脅，按照約束混凝土的要求來加強箍筋的配置，增加砼的延性，以克服地震時構件連接和變截面處的應力集中造成的坡壞，並吸收大量的地震能量，從而起到隔震，減震的效果。
  5. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
  6. Drilled holes and screw connections for busbars ; channel section busbars

    匯流條用鉆孔和螺紋連接件.槽形截面匯流條
  7. Agricultural machinery. endless hexagonal belts and groove sections of corresponding pulleys

    農業機械.環形六角皮帶和皮帶輪槽形截面
  8. In this way, when obturation cubage leave absorb oil cavity it connects the eduction oil cavity with the v trough and with the increasing of the turning angle, the size of the cross section of v trough become bigger and bigger, which make the pressure between the cavity of two blades much higher and higher, and until it completely connects the eduction oil cavity, it reaches the pressure of the eduction, and it can effectively reduces the fluid noise caused by high pressure return flow

    這樣，當密閉容積離開吸油窗口之後，通過v型尖槽逐漸與排油窗口連通，隨著轉角的增加， v型尖槽通流截面積逐漸增大，這就使兩葉片間容腔內的壓力逐漸升高，直至完全接通排油窗口時，才升壓達到壓油腔的壓力，這樣可以有效地降低因高壓迴流而引起的流體噪聲。
  9. By the operational results, the optimum plan should be : 2 additional crystal seeding tanks and a single tank with section - changeable stiring paddle

    根據運行結果，提出最佳配置方案為：增加2臺品種槽，選用單菜單槽配變截面攪拌槳。
  10. Abstract : it was deduced that the shapes of magnetic particle indicationsof point - type defects on workpiece surface depended on the resistance of carrier medium, and their dimensions depended on the volume of the defect equivalent cuboid, the magnetising characters of workpieces and magnetic particles, the strength of magnetic field, the lengths and sections of magnetic particles and the resistance character of carrier medium

    文摘:推斷出工件表面點狀缺陷磁痕的形狀取決于磁粉載體的介質阻尼力，磁痕大小取決于缺陷等效長方槽的體積、工件和磁粉材料的磁化特性、磁場強度、磁粉長度和橫截面積以及載體介質的阻尼特性等。
  11. Hydraulic fluid power - cylinders - housing dimensions forrectangular - sect bearing rings for pistons and rods

    液壓動力.汽缸.活塞及連桿用矩形截面軸承環溝槽尺寸
  12. Eigenvalue buckling analysis of channel corrugated plate assemblies under axial compression

    波紋槽型截面板組軸心受壓下的特徵值屈曲分析
  13. Endless hexagonal belts for agricultural machinery and groove sections of corresponding pulleys

    農業機械用的環形六角皮帶及皮帶輪的槽截面
  14. Simplified theories are also presented for curved beams with commonly used sections, such as i - shape, channel and h section without any symmetrical axis. linear analysis is also performed in combination with finite element method

    其後就常見的截面形式（單軸對稱工字形、槽形和無對稱軸的形截面） ，對所提出的曲梁理論進行簡化，並結合有限元方法求解曲梁的線性問題。
  15. Ould have good flexibility and flexing fatigue - resistance performance ; it should be anti - aging, oil - resistant and wear - resistant ; on the inner side of the back there should be point angel grooves of appropriate sizes made not only to meet technical de mands but also for purpose to improve the anti - wear performance, meanwhile, part of the noises shall be eliminated due to the escaping of the detained air between the be

    同步帶的背部用以粘結包覆抗拉元件，應有良好的柔韌性和耐曲撓疲勞性能，不易老化，耐油性好，耐磨損，在帶背的內表面開有適當大小的尖角凹槽，除因工藝要求外，還能改善帶的曲撓疲勞性能，同時在運轉過程中使帶與輪間的截流空氣逸出，以消除部分噪音。
  16. Rims for motorcycles ; part 3 : 5 tapered drop centre rims, rim profile 2. 50 a and 2. 50 c

    摩托車輪緣.第3部分: 5斜肩深槽論緣輪緣截面為2
分享友人
分享到 Line

分享到臉書