標準回轉表 的英文怎麼說

中文拼音 [biāozhǔnhuízhuǎnbiǎo]
標準回轉表 英文
standard swing meter
  • 標 : Ⅰ名詞1 [書面語] （樹梢） treetop; the tip of a tree2 （枝節或表面） symptom; outside appearance; ...
  • 準 : Ⅰ名詞1 （標準） standard; guideline; criterion; norm 2 （目標） aim; target Ⅱ動詞1 （依據; 依照）...
  • 回 : 回構詞成分。
  • 轉 : 轉構詞成分。
  • 表 : Ⅰ名詞1 （外面;外表） outside; surface; external 2 （中表親戚） the relationship between the child...
  • 標準 : （衡量事物的準則; 榜樣; 規范） standard; criterion; benchmark; pip; rule; ètalon （衡器）; merits
  1. The apsp produced abroad is made by numerical controlled machine tool, which has noise level of 71db ( a ), the apsp produced in our country is made in the method of exploratory which has noise level of 73db ( a ) and 75db ( a ). in order to analyze the influence of stator curve to noise, the author used tri - coordinate measuring instrument to measured exactly the inside surface of stator and got the straddling point coordinate, and made curve fitting by using matlab as language and studied the fitting effect and then worked out the equation of stator transition curve in return seeking, then comparied this method with the standard style and made the conclusion : the equation of atator transiting curve of apsp made by numerical controlled machine tool is close to theorical 5 power curve standard style, but compared with it, the stator transiting curve of apsp produced in exploratory has a major error. combining the testing results of noise, one can know that the qualily of stator transition curve play an importance to t he noise of the pump

    國外生產的汽車動力轉向泵是用數控機床加工的，其噪聲值為71db （ a ） ，國內生產的汽車動力轉向泵是用靠模方法加工的，其噪聲值分別為73db （ a ）和75db （ a ） ，為了分析定子曲線對泵的噪聲的影響，本人用三坐標測量儀對定子內表面進行精密測量，獲得定子內表面的離散點坐標，以matlab語言為工具對離散點進行曲線擬合，觀察擬合效果，然後，用回歸方法求出了定子過渡曲線的方程，並把該方程與理論方程標準型進行了比較，得出如下結論：用數控機床生產的汽車動力轉向泵的定子過渡曲線方程非常接近理論5次曲線標準型，而用靠模方法加工的汽車動力轉向泵的定子過渡曲線與理論5次曲線標準型相比較，則存在著較大的誤差，結合噪聲測試結果可知，定子過渡曲線的優劣，對泵的噪聲大小有著重要的影響。
  2. The paper analyzed the struture of the tri - eccentric butterfly vavle at length, defined the tri - eccentric butterfly valve, educed the geometry function and its characteristic about the section of the butterfly disc. the results indicate : the parallel contour line across butterfly disc thickness is normal ellipse, thereby eslablished function relations between its geometry parameters ( long axis and short axis ) of three primary sections of the butterfly disc and the tri - eccentricity ; in order to avoid interference between the butterfly disc and the valve seat as well as the valve body, combining the torque, we obtained the feasible range about the rotation center of the tri - eccentric butterfly vavle

    本文主要分析了三偏心蝶閥的結構，給出了三偏心的定義，推導出了蝶板截面的幾何方程及其性質，結果表明，沿蝶板厚度的平行截面輪廓線為標準的橢圓形，進而推導出了蝶板幾個主要截面的幾何參數（長軸、短軸）與三個偏心之間的函數關系；考慮到蝶板啟閉過程中避免與閥體及閥座發生干涉，結合蝶板的啟閉扭矩，確立了三偏心蝶閥回轉中心的適宜區域。
分享友人
分享到 Line

分享到臉書