標準錐度 的英文怎麼說
中文拼音 [biāozhǔnzhuīdù]
標準錐度
英文
standard taper- 標 : Ⅰ名詞1 [書面語] (樹梢) treetop; the tip of a tree2 (枝節或表面) symptom; outside appearance; ...
- 準 : Ⅰ名詞1 (標準) standard; guideline; criterion; norm 2 (目標) aim; target Ⅱ動詞1 (依據; 依照)...
- 錐 : Ⅰ名詞1. (錐子) awl2. (似錐物) awl-shaped things 3. (錐體) cone Ⅱ動詞(鉆) drill; bore
- 度 : 度動詞[書面語] (推測; 估計) surmise; estimate
- 標準 : (衡量事物的準則; 榜樣; 規范) standard; criterion; benchmark; pip; rule; ètalon (衡器); merits
-
The beyond is the simple notation of serial number of pricker, totaled 7 digits of codes, in which the first digit represents the diameter of needle - bar of pricker, the second digit represents the siding of triangle side on functional section of pricker, the third digit represent the length of functional section of pricker, whereas in standard notation, it represents the distance from needlepoint to gradual deflating small port ( lower port ), the fourth digit represents the total length of pricker, which is the distance from the inside of bending helve to the needlepoint, the fifth digit represents the total quantity of dents on the cording of functional section, and the sixth digit represents the model of barb on functional section, while the seventh digit represents the distance between barbs on functional section
以上為刺針編號的簡單寫法,共7位代碼,第一位是刺針針桿的直徑;第二位是刺針工作段三角面的邊寬;第三位是刺針工作段的長度,同標準寫法所不一樣的是針尖到漸縮錐小口(下口)的距離;第四位是刺針的總長度,按彎柄內側至針尖的距離;第五位是工作段棱上的總齒數;第六位是工作段上鉤刺的型號;第七位是工作段上鉤刺與鉤刺之間的距離。Standard test method for bulk density of tapered paintbrush filaments
錐形漆刷絲松密度的標準測試方法Standard guide for using the electronic cone penetrometer for environmental site characterization
環境定位特性用電子錐形透度計使用的標準指南Standard practice for cone penetrometer technology characterization of petroleum contaminated sites with nitrogen laser - induced fluorescence
帶有氮激光感應熒光的石油污染位點的錐形透度計技術特性的標準操作規程Standard test method for measuring edge taper and crown of flat - rolled electrical steel coils
扁軋電工鋼卷板邊緣錐度和凸面測量的標準試驗方法Angle masters with various angles, prisms, corner cubes and lage aperture and high precision cemented plate
不同角度的標準角塊、棱鏡、角反射器(角錐棱鏡)及大口徑、高精度的光膠板。Standard test method for density and unit weight of soil in place by the sand - cone method
用砂錐法現場測定土壤密度和單位重量的標準試驗方法Standard test method to measure viscosity by tapered bearing simulator at high temperature and high shear rate
在高溫和高剪切率下用錐形承載模擬器測量粘度的標準試驗方法Penetration consistency, expressed as the distance that a standard needle or cone penetrates vertically into a sample of the material under prescribed conditions of loading , time and temperature
針(錐)入度在規定的負荷、時間和溫度等條件下,以標準化的針或錐垂直進入產品試樣的深度來表示的稠度值。This paper validate the good or the bad of reachability from three point of view : firstly, putting forward reachable time and giving method that resolve the reachable time, the reachable time validate qualitative parameters with quantitative data. secondly, validating the good or the bad of reachability from view reachability, putting forward validation method of view reachability : validation method of relatively position and validation method of field of view and giving compute aided validation flow ; thirdly, validating the good or bad of rachability from space reachability, researching compute aided validation rule and contents and flow of task space. lastly, taking the group of wheel of the main undercarriage for example, illuminating compute aided validation method
針對可達性指標,本文從三個角度進行驗證:第一,提出可達時間的概念,給出可達時間的求解方法,從定量的角度來衡量定性指標;第二,從視覺可達的角度來評價可達性的好壞,提出視覺可達性的驗證方法:相對位置驗證法和視野內切錐驗證法,並給出計算機輔助驗證流程;第三,從作業空間可達性的角度來評價可達性的好壞,研究了作業空間計算機輔助驗證準則、內容和驗證流程。Standard test method for the determination of pyramid puncture resistance of unprotected and protected geomembranes
未保護和保護土木薄膜角錐穿孔強度的標準試驗方法Standard test method for high - shear viscosity using a cone plate viscometer
用錐板粘度計測定高速剪切粘度的標準試驗方法Standard depthwise taper
標準深錐度Standard test method for measuring viscosity at high shear rate and high temperature by tapered bearing simulator
用錐形承載模擬器在高剪切率和高溫下測量粘度的標準試驗方法Standard test method for yield stress of heterogeneous propellants by cone penetration method
錐入度法測定多相推進劑屈服應力的標準試驗方法Standard test methods for cone penetration of lubricating grease using one - quarter and one - half scale cone equipment
用1 4和1 2標度錐形設備測定潤滑脂錐入度的標準試驗方法Standard test methods for cone penetration of lubricating grease
潤滑脂錐頭針入度的標準試驗方法分享友人