模內修邊 的英文怎麼說

中文拼音 [mónèixiūbiān]
模內修邊 英文
in-mold trimming
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 內 : 名詞1. （內部; 里頭; 里邊） inner; inside; within 2. （妻子或妻子的親屬） one's wife or her relatives 3. （姓氏） a surname
  • 修 : Ⅰ動詞1 （修飾） embellish; decorate 2 （修理; 整治） repair; mend; overhaul 3 （寫; 編寫） write;...
  • 邊 : 邊Ⅰ名詞1 （幾何圖形上夾成角的直線或圍成多邊形的線段） side; section 2 （邊緣） edge; margin; oute...
  1. In this paper, the standard three - dimensional k - two - equation turbulence model which modifies the item of buoyant effect and simple algorithm are adopted, wall functions are used to deal with the boundary condition and a simplified method - box method is used to model the supply air boundary condition

    本文數值計算採用經過浮升力項修正的k -兩方程模型和simple演算法，壁面邊界條件採用標準壁面函數，風口邊界條件採用盒子方法。廠房內的氣流運動主要受風口出流動量的制約，因此選擇合理描述入流邊界條件的風口模型對數值模擬至關重要。
  2. In this article, simulations of air distribution in the vav air - conditioned office are carried out in the cases of different air - supplying diffusers including slot diffuser, sqaure grille, bar grille and square diffuser to supply air, the standard three - dimensional k - ? two - equation turbulence model with correctional item of buoyancy effect and simple algorithm are adopted, and wall function method is used to handle boundary conditions

    本文採用經過浮升力項修正的-兩方程模型和simple演算法，應用壁面函數法處理邊界條件，對利用包括條縫風口、方型百葉風口、長條型百葉風口和方型散流器不同型式送風口送風的變風量空調房間內的氣流組織進行了模擬。
  3. The solution formula of dwell time is deduced by using the pulse iteration method and the smoothing fourier transition method, and the formula can be simplified referring to workpiece shape. according to the anastomotic status of the tool and workpiece surface, we present the new model of the inherent relation among local pressure density, removal rate, convergence ratio and residual errors, and the corresponding formulas are given. the forming cause of the edge effect in the polishing process is analyzed, and the means which reduces the edge effect is put forward

    2 、針對計算機控制光學表面成形（ ccos ）的加工方式、誤差收斂特點，研製了去除函數呈高斯分佈的雙轉子結構研拋模；採用脈沖迭代法、平滑因子傅立葉變換法推導出駐留時間的演算法，求解過程中根據工件面形的特點作了各種形式的簡化；提出了工件表面和研拋模的吻合誤差與局部壓強、材料去除率、收斂比之間內在關系的數學模型，並推導出相應的計算公式；分析了邊緣效應產生的原因，在加工過程中採用相對壓力因子對去除函數進行修正，可以消除邊緣效應的影響。
  4. To get high operation speed and minish acute fluctuation at marginal running point, the thesis brings forward a new method : interior point method. the thesis also point out the spot price : should be modified by power flow method

    為了提高模型求解的速度和精度，減小實時電價在運行邊界點的劇烈波動，論文提出採用內點法進行模型的求解，同時也指出實時電價需採用潮流跟蹤法加以修正。
  5. The quality of reconstructed surfaces is related to many factors, such as quality of original data and surface fitting strategy, surface post - processing, and so on. in this thesis, the relative techniques of high quality surface reconstruction and surface interrogation based on triangular mesh are studied in depth. the main contents are as follows : ( 1 ) typical mesh smoothing schemes are analyzed

    本文對基於三角網格模型的高質量工程曲面重建及曲面光順性分析的相關問題進行了研究，主要內容包括: （ 1 ）在對現有幾種常用的三角網格模型光順演算法進行分析比較的基礎上，結合圖像處理中的kuwahara濾波以及雙邊濾波思想，提出了基於法矢修正的三角網格模型光順演算法。
  6. At the same time other domestic manufacturers integrated electronic control system fault diagnosis and other peripheral modules can be matching function modules, complementarity of the engine analyzer and decoder of advantages and disadvantages, making it maintenance personnel accede to the demands of open testing work platform

    同時集成了國內其他廠家電控系統故障診斷模塊及其它周邊可選配功能模塊，互補了發動機分析儀和解碼器的優、缺點，使其成為維修人員有求必應的開放式檢測工作平臺。
  7. The paper is based on the project of " the research of mathematics and computer frequency dynamic simulation theory on knobs not result ". the research content is object to the image of log knobs by vidicon getting to detect the shape of log knobs according to the method of video disposal. the paper apply digital image processing technology to log knobs image to swell and detect borders, then distill the surface shape and characteristic parameter of knobs. the thesis depict the knobs three - dimensional models, build the mathematics models of log knobs and simulation two - dimensional image curve of the log knobs primary section which has been discerned, thereby achieve our researching aim to reappear the knobs image on computer

    本論文是國家自然科學基金資助項目「節子ndt結果的數學描述與視頻動態模擬理論的研究」的基礎研究之一，論文的研究內容是通過視頻處理的方法檢測原木表面節子的形狀，以攝像機採集的原木表面節子圖像為對象，運用數字圖像處理技術對節子圖像進行修正、增強、邊緣檢測等處理，提取節子的形狀特徵參數，並運用數學的方法，歸納總結其規律，應用數學的方法對節子的二維模型進行描述，建立原木節子的數學模型，對識別出的原木節子主截面的三維圖像曲線進行擬合處理，從而在計算機上實現節子的分佈與形態的再現，達到研究節子的空間形態和分佈規律的目的。
分享友人
分享到 Line

分享到臉書