模具坯料 的英文怎麼說

中文拼音 [mójùpīliào]
模具坯料 英文
die blank
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 坯 : 名詞1 （未經燒制的磚、瓦、瓷等的製品） base 2 （土坯） unburnt brick; earthen brick; adobe 3 [方...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 模具 : mould; matrix; pattern die; die模具鋼 die steel
  1. The simulations of the blank forming process is always a very pop question in the domain of plasticity forming. it has very important significance as to making certain the figure of the blank roughcast calculating strain and stress, establishing reasonable forming craft and designing mold

    板料成形過程模擬一直是塑性成形領域研究的熱點問題，對于確定板料毛坯形狀、計算應力、應變分佈、制訂合理的成形工藝和模具設計有重要的意義。
  2. This paper focuses on the core part of the il & sm fixture system - information process system ( ips ). after relevant information is obtained from the current part, ips designs the roughcast and the parameters of stuffing, matches or designs rational locating box, positions all the locating bolt, finishes the procedure of datum conversion and ensures the communications between state shaping system, part fixing system and nc programming system

    本文的研究對象為il & sm夾具系統的核心部分? ?信息處理系統（ informationprocessingsystem ? ips ） ，它通過獲取零件的相關信息，進行毛坯與填料厚度的設計，設計或配置出合理的尋位箱，智能布置尋位元件，完成基準轉換，並負責與狀態成型系統、工件安裝系統、 nc編程系統等模塊的通訊。
  3. In different in terne die travel, the metal flow characterize in warm extrusion forming processes and the affection for the flow of metal stage which made by the difference between the blank bottom altitude and the axial direction limiting size in warm extrusion forming technique have been analysed we have gotten the equivalent strain field and the velocity field and other field variable that the blank in different in terne die travel and the die travel - load curve. at the same time, we have analyzed the contributing factor for the oil pump stator forming process optimized and achieve thereasonable die parameter for the war m extrusion forming finally, the optimized technics parameters were used into pilot production, then the qualified oil pump stator forging were produced, the analog results were compared with those of pilot production

    論文具體分析研究了不同成形工藝過程中金屬流動的特點，並對不同凸模行程下溫擠成形過程中的金屬流動特點、坯料連皮厚度（底部高度）與溫擠壓成形工藝中的軸向界限尺寸的差值對金屬變形階段的影響進行了分析，獲得了坯料在不同凸模行程下的等效應變場、速度場等場變量及凸模行程-載荷曲線，同時對油泵定子成形過程的影響因素等進行了分析，優化並獲得了合理的溫擠成形工藝及模具參數。最後，利用模擬優化獲得的各項工藝參數進行生產實驗，得到實際生產出的合格油泵定子件，並將模擬結果與生產實驗結果進行比較。
  4. In the paper, the finite element simulation software dynafrom is applied to analyze the affect of different blank holder during the forming process of laminose stepped tubular part, predict the possible defects such as wrinkle and break, obtain the rational style of blank holder avoiding the occur of defects and determine the rational configuration of die. the forming affect of thin - wall shallow stepped tubular part is analyzed when using different lubricate condition ( friction coefficient ). by this method, the relationship between friction coefficient and drawing depth of laminose stepped tubular part is obtained

    本文利用有限元模擬軟體dynafrom分析了不同類型的壓邊圈對薄壁階梯筒形件成形過程的影響規律，預測了採用不同類型壓邊圈時可能出現的成形缺陷如起皺和拉裂，獲得了防止缺陷產生的合理壓邊圈形式，確定了合理的模具結構形式；分析了不同的潤滑條件（摩擦系數）對薄板階梯筒形件成形的影響，獲得摩擦系數與薄板階梯筒形件的拉深深度的關系；分析了階梯筒形件成形過程中的不同階段的應力應變分佈、毛坯材料厚度變化情況，並獲得了階梯階梯筒形件能一次拉深成形的條件。
  5. The non - uniform deformation behavours and the movement of the weld seams, the wrinkling of the workpieces and the methods to control the non - uniform deformation were investigated by adjusting the die structures, the blank holding method and the blankholding force distribution

    通過調整模具結構和壓邊方法及壓邊力分佈，對坯料不均勻變形規律及焊縫的移動規律、坯料的起皺規律及控制坯料不均勻變形的方法進行了探討研究。
  6. The factory specializes in manufacture of cm series fully automatic, semiautomatic bottle blowing machines, injection and blow mould, pet bottle preform and cap of various specifications and space cup etc with famous brand lonhon

    專業生產「龍宏」牌cm系列全自動、半自動吹瓶機、注吹模具、太空杯以及各種pet瓶坯，塑料防盜蓋等相配套產品。
  7. We mainly make moulds for injection plastic mould, bumper mould, car lighting mould, pet performs mould, die casting mould, pipe fitting mould, water dripper mould, bottle blowing mould, daily use articles mould, bmc dmc smc mould ect, and the relative daily plastic products

    主要以家庭日用塑料品模具各類汽車摩托車配件模具，電器模具，管坯模具，瓶蓋模具，塑料管件模具，塑料注射模具，吹瓶模具，擠出模具，各類bmc dmc smc壓鑄模具，精密模具製造為主。
  8. The metal flowing pattern of the tooth filling process at different stages during closed die extrusion is found through lead deformation test and double - acting extrusion method on a doubled - acting press or on a special die structure with a general press is proposed

    成形試驗獲得了金屬充填齒形腔的流動模式，提出採用專用雙動壓力機或在通用壓力機上採用特殊模具實現坯料雙向擠壓的成形方法。
  9. Drawing piece unfold size is one basic condition under the calculation on coefficient, number of drawing, handbooks or books of press are not given, practice press production, die designer designs drawing die by experience calculation, after testing, according to deformation, state, defect shape of testing blank, shape and unfold size is revising, finally, unfold size and shape of blank are determined, designing period is longer, cost of die and work piece is to raise, economic benefit is to reduce

    拉深件展開尺寸是拉深可行性分析中計算拉深系數與拉深次數的前提條件，現有沖壓手冊或教材對于復雜拉深件的展開尺寸計算尚未論述。復雜拉深件的沖壓生產中，模具設計者憑經驗估計拉深可行性，設計製造拉深模進行反復試壓，根據試壓件的形變狀態，缺陷形貌，制定坯料展開尺寸和形狀，周期較長，因而生產成本高，經濟效益不佳。
  10. Firstly, the comparation study between the wedge pressing and the contour forging has shown that the transverse deforming initiated from the surface of the preforms. when the superficies reached the moulding wall, the deforming moved downwards as the high - direction deforming increased, till the moulding chamber was full of stock ; the transverse deforming of the moulding pressing stock initiated from the center of the stock then surned into a drum - type. the distribution of the density and hardness of the high - direction indicated that the wedge pressing acquired a better ability of pressing penetration

    首先對比研究了楔形壓制工藝與模壓緻密化工藝，發現楔壓坯料的橫向變形從上表層開始，當上表面與模壁接觸后，隨著高向變形量的增加逐步向下移動，直至坯料充滿模腔;模壓坯料的橫向變形從坯料中間開始，形成鼓形。高向的密度、硬度分佈表明楔壓比模壓具有更好的壓透能力。
  11. Analysis which was based on the fracture mode of mould in wire - cutting processing, and the results show that the partial - quenched of mould, the non - uniformity of blank temperature and the carbide segregation inside the material are the main reasons of deformation and cracking

    摘要通過分析在線切割加工中模具的破壞形式表明：模具不完全淬火、坯料溫度的不均勻分佈、材料內部的碳化物偏析是模具變形與開裂的主要原因。
  12. On the basis that characteristics of every forming methods have been summarized and concluded, according to the moving relationship between working parts of die and block, it is proposed the successive partial plastic forming methods for groove have been divided to two kinds of basic deformation styles, rolling and splitting extrusion

    在總結歸納各種方法變形特徵的基礎上，根據模具工作部分與坯料之間的運動關系，提出槽的連續局部塑性成形可劃分為滾軋與劈擠兩種基本變形方式。
  13. The paper still using the combining of unigraphics and dynaform to simulate and reversely seek sketchy size of part, and to gain reasonable sketchy size of part and size of mould

    本文還利用unigraphic三維建模軟體和dynaform板料數值模擬軟體的結合對零件的坯尺寸進行了反求模擬，得到了合理的零件毛坯尺寸和模具尺寸。
  14. In this paper, by using non - linear finite element software, ansys / ls - dyna, simulate a forming of auto fall to ground skeleton part, get the contour of the semi - finished product, forecast the change of the blank thickness and the probable wrinkling, cracking, and from the simulation of the spring - back, obtain the spring - back tendency. so, get technology parameters, which are inextricable to forming production. all these will pose great significant to production in theory and reality

    本文運用非線性有限元軟體ansys ls - dyna對汽車落地骨架零件進行了沖壓成形的數值模擬，得出了毛坯外形，預測了成形過程中板料壁厚變化和可能出現的起皺、破裂現象，通過回彈模擬，預測了回彈趨勢，獲得了該類零件成形所需要的工藝參數，對實際生產具有一定的指導作用。
  15. The forging process of steering bar was simulated by using this algorithm, much informations about steering joint forging process were in good accordance with the experiments

    將模具處理成剛體，轉向節坯料看作彈塑性體，探索了轉向節在鍛造成形過程中材料的流動規律。
分享友人
分享到 Line

分享到臉書