模塊材料表 的英文怎麼說

中文拼音 [mókuāicáiliàobiǎo]
模塊材料表 英文
modular bom
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 塊 : 名詞（古時佩帶的玉器） penannular jade ring （worn as an ornament in ancient china）
  • 材 : 名詞1 （木料） timber 2 （泛指可以直接製成成品的東西; 材料） material 3 （供寫作或參考的資料） ma...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 表 : Ⅰ名詞1 （外面;外表） outside; surface; external 2 （中表親戚） the relationship between the child...
  • 模塊 : camac module,camac
  • 材料 : 1. （原料） material 2. （資料） data; material 3. （適于做某種事的人才） makings; stuff
  1. The nano - bulk al should be kept more man 30 minutes at temperature no more than 300 to annealed which is much lower than that of ordinary aluminum materials

    對納米鋁塊體材料的退火實驗表明，模壓成形的鋁塊體材料的退火溫度（ 300 ）比常規的鋁材（ 400 ）要低，退火保溫時間應在30分鐘以上。
  2. The density of the al bulk nanomaterials is only 75 percent of mat of normal ordinary coarse crystallized counterparts, which means there are a lot of holes or loosen structure in the nano - bulk al

    通過模壓成形的納米金屬鋁和銅的塊體的密度只有普通體材料密度的75左右，表明得到的未經燒結的納米鋁塊體內部可能還存在很多孔隙或很多疏鬆的組織。
  3. After the seawater desalination equipment was successfully brought to market, our company also promoted the ultra - pure water equipment suitable for electronic and medical industry according to the demands of the market. it uses an edi membrane from american electropure co., ltd, the conductance and ohmmeter are from hanna co., ltd. all spare parts of equipment are made of the highest quality materials

    公司在成功地把海水淡化設備推向市場后，又應市場的需求推出了適于電子醫藥等行業用的超純水設備，即jhh - edi系列。其關鍵器材採用美國著名的electropure公司的edi模塊，及hanna公司的電導率電阻率表。其他主要配件則採用國產優質材料及配件。
  4. The experiments show all the compression strength shear strength, elastic modulus of the composite blocks and their masonry can satisfy the requirements of standard compared to concrete, the haojiao materials elastic modulus is so low that we ignore it ' s improvement to the composite block ' s compression strength. however the area of horizontal mortar joint of composite block masonry is enlarged just because of the haojiao materials " existence, so the shear strength of composite block masonry is higher than one of small hollow betonblock masonry in thermal performance, the heat - preservation and heat - insulation capabilities of composite block masonry are analyzed and researched

    試驗表明：復合砌塊及其砌體的抗壓、抗剪強度、彈性模量等均滿足規范規定的要求；由於昊角材料與混凝土相比，彈性模量相差懸殊，在受壓時，可以不考慮昊角材料芯塊對復合砌塊及砌體抗壓強度的提高，同時又因為昊角材料的存在，砌體水平灰縫面積增大，復合砌塊砌體的抗剪強度較空心砌塊砌體有較大的提高。
  5. The multi - purpose tester developed here is aim at testing the mechanics performance of the brittle material, which bases on modular design thought, it contains several modules as the machinery load component, platform of supporting, the function modules and the software system, they can be combined in different function modules to satisfies the need of different application situation. the tester can be used to measure not only general material properties such as elastic modulus, ultimate strain, strength, hardness and toughness, fatigue properties but also various special properties such as the local strength, and surface residual stress at the different location of the brittle component with non - destructive methods. thus the security and reliability of the brittle component can be evaluated and predicted

    本文基於模塊化設計思想，研製了一臺專門針對脆性材料力學性能測試的多功能脆性材料試驗儀，其主要包括機械加載模塊、支撐平臺、功能模塊、測控系統、軟體系統等模塊，通過對這些模塊的不同組合可實現不同的功能及滿足不同應用場合要求;系統除了具有測試脆性材料的彈性模量、極限應變、強度、硬度、韌性等常規性能外，還具有無損測試玻璃構件不同位置的局部強度和表面預應力，進而對玻璃構件的安全可靠性和壽命進行預測等功能。
  6. To creat the parametric model of wheel, and then to use ansys to optimize it. the result shows the weight of the wheel is reduced remarkably and the maximal stress in wheel approaches its breaking point and its distributing is more rational

    然後，參數化構建車輪模型，利用ansys的優化模塊對其進行優化，優化結果表明，車輪的重量有了顯著的減少，車輪的最大應力接近材料的許用應力，且分佈更合理。
  7. The steady of grottoes attacked by earthquake is analyzed with the engineering soft named adina, in order to show where the weak parts of grottoes are and time - history curves of the horizontal displacement of the easily damaged nodes and time - history curves of first and third principal stress of the easily damaged elements

    （ 3 ）以大型adina有限元分析軟體為基礎，編制了預應力錨索材料的非線性有限元計算程序模塊，研究石窟在地震作用下的穩定性問題。選取能代表石窟整體結構的三個不同剖面作為有限元計算模型，並採用不同工程特性的地震動加速度時程作為荷載輸入。
分享友人
分享到 Line

分享到臉書