模塊調試 的英文怎麼說

中文拼音 [mókuāidiàoshì]
模塊調試 英文
module debugging
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 塊 : 名詞（古時佩帶的玉器） penannular jade ring （worn as an ornament in ancient china）
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 模塊 : camac module,camac
  • 調試 : shakedown test; debug; debugging
  1. ( 3 ) the dissertation designs the hardware diagrams of corelation matrix module and spectrum peak finding module. accroding to the hardware diagrams, the dissertation codes by vhdl and do function simulation and timing simulation

    （ 4 ）本文對music演算法的各模塊進行了互連調試工作。當採用了altera公司cyclone系列的fpga實現music演算法時，單次運算時間在20us以內。
  2. Finally we implemented the system by using vc + +, including video collecting, coding, network dibble seeding and live broadcast

    最後利用vc + +對系統軟體模塊進行編寫和調試，主要實現了視頻信息的採集、壓縮及其網路點播和直播等功能。
  3. The advantage of palm waxes in candles is that they do not need additives other than colorants and fragrances ; they can be formulated to ensure easy mold release and good burning and are available in beads and blocks

    用棕櫚蠟製造蠟燭的優勢在於它們不需要添加著色劑和芳香劑以外的添加劑；它們可以調試到保證容易脫模、有好的燃燒效果、容易成型到珠狀和塊狀。
  4. Finally the paper develops program with c language which adopts proscenium - background control mode and modularized architecture, and it passes the debugging

    最後本文採用前後臺控制模式和模塊化結構，用c語言開發了完成數控系統功能的軟體，並通過了調試。
  5. The three - order modulator has a 2 - 1 cascaded structure and 1 - bit quantizer at the end of each stage, the modulator is implemented with fully differential switched - capacitor circuits. and then, the discussion will begin by exploring the design of various circuit blocks in the modulator in more detail, i. e., ota, switched - capacitor integrator, quantizer, two - phase non - overlapping clock signal, etc., at the same time, these circuits will be simulated in spectre and hspice. at last, the whole cascaded modulator will do behavioral level simulation by matlab soft and simulink toolbox

    本論文中，首先介紹模數轉換器的各種參數的意義，以及一階sigma - delta調制器和高階sigma - delta調制器的原理;給出解決高階單環sigma - delta調制器不穩定性的方案，引入級聯結構調制器，特別針對級聯結構調制器中的失配和開關電容積分器的非理想特性進行詳細的討論;本設計的sigma - delta調制器採用2 - 1級聯結構和一位量化器，調制器採用全差分開關電容電路實現;同時對整個調制器的各個模塊進行了電路設計，包括跨導放大器、開關電容積分器、量化器、兩相非交疊時鐘等，並利用hspice和spectre模擬工具對這些電路進行模擬測試;最後，利用matlab軟體和simulink工具對整個級聯調制器進行行為級模擬。
  6. It makes use of resource of the chip, realizes the development of every module, achieves distilling of telegraphese, builds up new frame, calculates the position and provides external interface. in the section of calculating the position, the author combines the two measures of carrier phase position and code position. finally, in the platform of matlab, the author completes the function simulation of main modules

    概述了接收機的設計原理;詳細描述了基於ti公司的tms320c6713dsp晶元的系統程序設計中各模塊的實現，利用該晶元的資源，實現各模塊的調度，完成對導航電文的提取，重新組幀，定位解算以及對外介面;在解算部分，把載波相位定位與碼測距定位相結合，利用載波相位對偽距的平滑來提高定位精度;在matlab平臺下進行了各模塊的功能模擬測試，以模擬結果的圖表來分析說明了載波相位平滑偽距的兩種演算法能使定位精度有一定的提高。
  7. The subject has mainly finished designing and debugging software and hardware of a / d decode module, fpga video processing module, video data frame deposit module, base clock produce module, d / a encode module, i2c bus control module, etc. a / d decode module gathers analog tv signals and realize video decode ; fpga video processing module deals with the data after decoding and produces systematic logic control signal ; video data frame deposit module offers the buffering area to a large n umber of high - speed video data ; base clock produce module through input basic video signal offers system accurate relevant synchronous signal ; under control of video processing module d / a decode module convert digital video data into compound tv signal which can be shown in tv directly ; i2c bus control module is used to initialize the chip of system by simulating i * c bus timing

    本課題主要完成了a d解碼模塊、 fpga視頻處理模塊、視頻數據幀存模塊、基準時鐘產生模塊、 d a編碼模塊、 i ~ 2c總線控制模塊等部分軟、硬體設計及調試。其中a d解碼模塊採集模擬電視信號實現視頻解碼； fpga視頻處理模塊對解碼后的數據進行去噪處理的同時還負責系統的邏輯控制；視頻數據幀存模塊為大量高速的視頻數據提供緩沖區；基準時鐘產生模塊通過輸入基準視頻信號為系統提供精確的相關同步信號； d a編碼模塊在視頻處理模塊的控制下把數字視頻數據轉換成復合電視信號供顯示用： i ~ 2c總線控制模塊模擬i ~ 2c總線時序實現對系統中編、解碼晶元的初始化。
  8. Through analyzing in theory and proving in practice, this paper indicates that the module - control system have many merits : the develop cycle is short ; the application of room is sufficient ; the problem will be found easily in the process of debugging ; the capability of anti - jamming is strong ; maintain and check errors easily ; interchangeability is good ; upgrade is easy

    通過理論分析和實踐證明，本文認為模塊化控制具有開發周期短、充分利用空間、在調試的時候容易發現問題、抗干擾能力強、容易維修和檢查錯誤、降低維修成本、互換性強、容易改進和升級等優點。
  9. Experiments have failed in the process of debugging station fire mode of the first opening segment of guangzhou metro line 3, the main reason is the delay protect module of wind valve which cut off power supply

    摘要廣州地鐵3號線首通段車站火災模式調試過程中，出現火災模式執行失敗，主要原因在於風閥延時保護模塊動作切斷電源。
  10. And debugging practice has testified that in this scheme the receiving dsp can accurately decode all the signals from handsets

    本課題實現了正確解碼手機上行信號，為以後階段的測試模塊調試打下了基礎。
  11. All program of production line system and control and monitor system are designed for modularization, which comes to the aim largely by the emulational debugging

    生產線系統和通信監控系統的程序採用模塊化設計，經模擬調試。基本可達到設計要求。
  12. Finally, the module debug and task implement are mainly carried out using serial port and network in host ’ s environment. these are supported for further data management in reality of micro satellite

    最後主要利用串口和網口結合主機進行任務模塊程序的編寫和功能模塊調試，這些工作對最終進行微小衛星航天應用打下一定的基礎。
  13. This paper had did the most important work was the design of transciever and the construction of working environment, and also the video module and power amplifier module. at last, we did the measurement and debugging of total system, achieved anticipate target, satisfied the requirement of communication

    本文所做的主要工作在於發射機總體設計和工作環境的構建，發射機視頻模塊，調制模塊以及功率放大器模塊的設計，最後對系統進行了總體的調試，達到預期指標，滿足了要求。
  14. The system can be satisfied for engine ignition after simulation debugging, this supplies some references for design of engine electric control later

    該系統進行模擬調試后，基本可以實現發動機的基本點火要求，為以後設計用於發動機電控模塊（ ecm ）的控制軟體提供了一定的參考。
  15. This paper sums the situations and trends of domestic and international engineering machinery firstly, discusses the demands and implements of intelligent and long - range monitoring and controlling, and constructs a three - layer model of the engineering machinery long - range monitorin and control system : the front unit control systems, the machine - mounted monitoring system and the long - range control center ; proposes a kind of structure of embedded system based on c / os - ; dissects the characteristics, structure, operation and schedule principle of c / os -, modified the kernel, and improves dependability of the schedule algorithm ; designs the hardware in detail : the microprocessor at91rm9200, the store unit, the serial interface, the human - computer interaction interface, the can bus control module, the debug interface and the reset circuit etc. ; on this basis, succeeds in transplanting c / os - to the system, sets up the operating system framework, designs the driver, sets up the institutional framework of upper user ' s application, provides the method and concrete application process of the graphical user interface module based on c / os -. the system designed in this paper, not only has the functions of local control, friendly human - computer interface, but also has various interfaces which make the system can be managed by the long - rang center

    本文首先綜述了國內外工程機械行業發展的現狀和趨勢，闡明了實施工程機械智能化及遠程監控的意義和需求，並為此構建了工程機械遠程監控系統三層結構模型:前端單元控制系統、車載監控系統和遠程監控中心;提出了一種基於c / os -的嵌入式車載監控系統構建方案;深刻剖析了c / os -的特點、內核結構、運作機理、調度演算法，在此基礎上對其內核進行移植前的必要修改，並對其調度演算法進行了可靠性改進;對構成嵌入式系統硬體的各個主要部分:嵌入式微處理器at91rm9200 、存儲單元、串列介面、人機交互介面、 can總線控制模塊、調試介面以及復位電路等做了詳細的設計;在此基礎上，成功地將c / os -實時內核移植到本文研發的嵌入式硬體系統中，建立了車載監控系統的操作系統體系結構，編寫了該操作系統的底層硬體驅動程序，建立了上層用戶應用程序的組織結構，並給出了圖形用戶界面模塊化應用程序在c / os -操作系統上的建立方法和具體應用過程。
  16. This method is called on a dynamic module that is not a debug module

    對不是調試模塊的動態模塊調用此方法。
  17. You have just built and tested your first visualizer. if you want to use your visualizer in visual studio rather than simply calling it from the test harness, you need to install it

    如果希望在visual studio中使用您的可視化工具，而不是僅從測試裝具模塊調用，則需要安裝該可視化工具。
  18. The main work that i " ve done in the dissertation is : participating the design of the total test scheme, designing by myself the adapter for testing the modules of a computer, completing test programs. the most important and difficult things in the dissertation is the programs for testing memory by automatic test equipment

    特別說明的是在論文所述工作中，我所做的主要工作有：參與了總體測試方案的設計；獨立設計並調試了一個計算機產品中所有被測模塊的子適配器，設計並調試了模塊測試的測試程序。
  19. The main work of this thesis is as follows : firstly, the display principle of tft - lcd is expatiated ; secondly, test software for tft - lcd module is written, including tft - lcd module interface programme, tft - lcd test programme, touching panel driving programme and gui ( graphics user interface ) programme ; thirdly, test software is debugged and analyzed ; finally, optics characteristics and electric characteristics of standard tft - lcd module are tested by this test software, and tested data are analyzed

    二、 tft - lcd模塊測試軟體設計，具體包括tft - lcd模塊介面程序程序設計、 tft - lcd測試程序設計、觸摸屏程序設計以及圖形用戶界面程序設計。三、對測試軟體進行調試分析。四、採用測試軟體對標準的tft - lcd模塊的光學特性和電氣性能進行測試，並分析比較所測得的數據。
  20. This paper deals with in detail the system design of the computer data encryption card pcijmc2000, the model function and hardware circuit designn, pcb design, software design and model debugging

    論文詳細論證了pcijmc2000的系統方案設計，論述了pcijmc2000的模塊功能與硬體電路設計， pcb設計，軟體設計及模塊調試，完成了pcijmc2000卡的硬體試制。
分享友人
分享到 Line

分享到臉書