模度坯料 的英文怎麼說
中文拼音 [módùpīliào]
模度坯料
英文
die block-
The powder was pressed through molding and cold isostatic pressure, which increased the density and decreased the uneven distribution of stress inside the briquet to make the ceramic briquet equally compact
粉料採取模壓和冷等靜壓相結合的方法壓制，增大了坯體內部的密度並減少了應力的分佈不均，得到均勻緻密的陶瓷坯體。This paper focuses on the core part of the il & sm fixture system - information process system ( ips ). after relevant information is obtained from the current part, ips designs the roughcast and the parameters of stuffing, matches or designs rational locating box, positions all the locating bolt, finishes the procedure of datum conversion and ensures the communications between state shaping system, part fixing system and nc programming system
本文的研究對象為il & sm夾具系統的核心部分? ?信息處理系統（ informationprocessingsystem ? ips ） ，它通過獲取零件的相關信息，進行毛坯與填料厚度的設計，設計或配置出合理的尋位箱，智能布置尋位元件，完成基準轉換，並負責與狀態成型系統、工件安裝系統、 nc編程系統等模塊的通訊。In different in terne die travel, the metal flow characterize in warm extrusion forming processes and the affection for the flow of metal stage which made by the difference between the blank bottom altitude and the axial direction limiting size in warm extrusion forming technique have been analysed we have gotten the equivalent strain field and the velocity field and other field variable that the blank in different in terne die travel and the die travel - load curve. at the same time, we have analyzed the contributing factor for the oil pump stator forming process optimized and achieve thereasonable die parameter for the war m extrusion forming finally, the optimized technics parameters were used into pilot production, then the qualified oil pump stator forging were produced, the analog results were compared with those of pilot production
論文具體分析研究了不同成形工藝過程中金屬流動的特點，並對不同凸模行程下溫擠成形過程中的金屬流動特點、坯料連皮厚度（底部高度）與溫擠壓成形工藝中的軸向界限尺寸的差值對金屬變形階段的影響進行了分析，獲得了坯料在不同凸模行程下的等效應變場、速度場等場變量及凸模行程-載荷曲線，同時對油泵定子成形過程的影響因素等進行了分析，優化並獲得了合理的溫擠成形工藝及模具參數。最後，利用模擬優化獲得的各項工藝參數進行生產實驗，得到實際生產出的合格油泵定子件，並將模擬結果與生產實驗結果進行比較。In the paper, the finite element simulation software dynafrom is applied to analyze the affect of different blank holder during the forming process of laminose stepped tubular part, predict the possible defects such as wrinkle and break, obtain the rational style of blank holder avoiding the occur of defects and determine the rational configuration of die. the forming affect of thin - wall shallow stepped tubular part is analyzed when using different lubricate condition ( friction coefficient ). by this method, the relationship between friction coefficient and drawing depth of laminose stepped tubular part is obtained
本文利用有限元模擬軟體dynafrom分析了不同類型的壓邊圈對薄壁階梯筒形件成形過程的影響規律，預測了採用不同類型壓邊圈時可能出現的成形缺陷如起皺和拉裂，獲得了防止缺陷產生的合理壓邊圈形式，確定了合理的模具結構形式；分析了不同的潤滑條件（摩擦系數）對薄板階梯筒形件成形的影響，獲得摩擦系數與薄板階梯筒形件的拉深深度的關系；分析了階梯筒形件成形過程中的不同階段的應力應變分佈、毛坯材料厚度變化情況，並獲得了階梯階梯筒形件能一次拉深成形的條件。Abstract : in this paper, the kinematically admissible velocity fields are established by using the metal flow patterns based on the experiments, and the configuration dimensions of billet and the curves of load - stroke in precision forging process for spur gear from solid billet are simulated on computer by upper bound method. the results acquired in the simulation are in good agreement with those obtained in the experiments
文摘:本文利用有實驗根據的變形流動模式建立動可容速度場，利用上限法模擬用實心坯料精鍛直齒圓柱齒輪時坯料的外形尺寸變化和力?行程曲線，所得結果與實驗測定值很一致，可供沖擠精鍛工藝設計參考。Regard to this problem, hengxing company, through repeated and numerous experiments, has finally concluded a solution : we use a kind of ultra - wear - resisting and high - molecular material to fix, stuck by a super bond, on the surface of the frame
造成磚坯質量不同程度的降低，針對這種問題，恆星公司的技術部門，經反復實驗，終于總結出一種方法，用一種超耐磨，高分子材料，配以超強粘合劑，將其固定在模框表面。Firstly, the comparation study between the wedge pressing and the contour forging has shown that the transverse deforming initiated from the surface of the preforms. when the superficies reached the moulding wall, the deforming moved downwards as the high - direction deforming increased, till the moulding chamber was full of stock ; the transverse deforming of the moulding pressing stock initiated from the center of the stock then surned into a drum - type. the distribution of the density and hardness of the high - direction indicated that the wedge pressing acquired a better ability of pressing penetration
首先對比研究了楔形壓制工藝與模壓緻密化工藝，發現楔壓坯料的橫向變形從上表層開始，當上表面與模壁接觸后，隨著高向變形量的增加逐步向下移動，直至坯料充滿模腔;模壓坯料的橫向變形從坯料中間開始，形成鼓形。高向的密度、硬度分佈表明楔壓比模壓具有更好的壓透能力。Analysis which was based on the fracture mode of mould in wire - cutting processing, and the results show that the partial - quenched of mould, the non - uniformity of blank temperature and the carbide segregation inside the material are the main reasons of deformation and cracking
摘要通過分析在線切割加工中模具的破壞形式表明：模具不完全淬火、坯料溫度的不均勻分佈、材料內部的碳化物偏析是模具變形與開裂的主要原因。Three factors, such as pull - up type, the materials and structure of crystallizing mould, and the temperature field in crystallizing mould, influencing on continuous up - casting for aluminum were analyzed, which laid the foundation of the application to continuous up - casting technology for aluminum bar
分析研究了引拔拉坯制式、結晶模材料及結構、結晶模內溫度場三因素對鋁上引連鑄的影響規律，結果表明上引連續鑄造過程中施加適當頻率的反推和反推量有利於桿坯連鑄的持續，結晶模自身的性能及模內溫度場的狀態對金屬鋁桿上引連鑄工藝的實現有直接影響。Based on the established three - dimensional physical model, simplified terms, specified material parameters in thermal and physical properties, boundary conditions, and the calculation method of heat convection of cooling water, the numerical simulation and analysis on steady - state temperature field for continuous unidirectional solidification of niti shape memory alloy wire billets were proceeded under the condition of different combined parameters using ansys finite - element software
在建立三維物理模型以及確定材料熱物性參數、邊界條件與冷卻水對流換熱系數計算方法的基礎上，採用ansys有限元軟體對不同參數組合條件下鎳鈦形狀記憶合金線坯連續定向凝固的穩態溫度場進行了數值模擬。This article makes a model test research to filter function of porcelain sand filter according to the new material - porcelain sand filter - that baogang uses in the new water processing technology of sheet semifinished turbidity of the inlet water, different medicine and variation of outlet water quality in different filter velocity
本文針對包鋼薄板坯連鑄連軋新水處理工藝中所採用的新型濾料? ?瓷砂均質濾料的過濾特性進行了研究。在不同的進水濁度、不同的加藥量、不同的濾速下出水水質的變化，對瓷砂濾料過濾性能進行了模型試驗研究。Steps were made on the female die surface to make up for the thickness different of the blanks
凹模表面和型腔加工了臺階以補償坯料的厚度差值。分享友人