模數 的英文怎麼說

中文拼音 [móshǔ]
模數 英文
[物理學] modulus; module; modulo; mod
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 數 : 數副詞（屢次） frequently; repeatedly
  1. As a mix - mode chip, the application - specific controller including analog signal and digital signal processing block can be applied to receiving, amplifying, processing, controlling signals of pir, and offer a wide application in some fields. in analog circuits, by sub - threshold mosfet, a self - bias current source is presented, which has a high power supply restrain ratio and a complementary to absolute temperature characters

    這款晶元是一款數模混合晶元，包括模擬信號處理（含模數介面模塊）和數字信號處理兩大模塊，完整實現對紅外信號的接收、放大、處理、控制，產生有效數字電平驅動繼電器、可控硅等負載，應用於自動燈等多種場合。
  2. Application and principle of super - high speed adc tlv

    5580超高速模數轉換器原理及應用
  3. Analyzes and application of adc technology

    模數轉換技術的分析與應用
  4. The new system consists of a single - chip computer system ( at89c51 + psd311 ) and alow power consumed analyzer by applying a new adc chip ads774, and a dead - time correcting circuit is designed to correct the collecting time

    本系統由單片微機系統（ at89c51 + psd311 ）組成多道緩存，由低功耗模數轉換器組成分析器，與微型計算機通過列印并行介面實現數據通訊，並含有死時間校正電路。
  5. Wherethe long bridge deck within 0. 5 l amidships is regarded as strengthdeck, the midship section modulus and minimum thickness of the deckplating comply with the requirements of 2. 2. 1 and 2. 4. 2. l of this ischapter

    例1 :在船中部0 . 5l區域內的長橋樓甲板作為強力甲板時，其船中剖面模數及最小厚度應滿足本章2 . 2 . 1及2 . 4 . 2 . 1的要求。
  6. Stand ard for modular coordination of dwelling houses

    住宅建築模數協調標準
  7. Ceramic tiles - determination of modulus of rupture and breaking strength

    瓷磚.破裂模數和破壞的測定
  8. Average bulk modulus

    平均體積彈性模數
  9. Chain transmissions. profile of chain wheel modual cutters

    鏈傳動.鏈輪模數截斷器的剖面
  10. In this dissertation, the analog - digital channelized receiver is studied. the optimized system, spectrum reconstructing and accuracy signal frequency estimation algorithms are researched

    本文研究了模數混合通道化接收方案，著重研究其優化結構和關鍵技術以及線性調頻信號參數估計演算法。
  11. The output of the sample-and-hold system now goes into an analog-to-digital converter.

    取樣和保持系統的輸出現在又進入一個模數轉換器。
  12. A d and d a conversion

    數模與模數轉換
  13. Straight bevel gears for general engineering and heavy engineering part 2 : modules and diametral pitches

    一般和重型機械用直齒錐齒輪.第2部分:模數和齒距
  14. Within the same width of old dpn ( 18mm ), the new products got 3 kinds of breaking capacity which is 4. 5ka 6ka and 10ka to comfort our customer

    新dpn在沒有改變原有模數寬度（ 18mm ）的前提下。分別有4 . 5ka6ka10ka三個等級的分斷能力來供您選擇。
  15. Design manual for enclosed epicyclic metric module gear drives

    封閉行星米制模數齒輪傳動裝置匠設計手冊
  16. Secondly, it describes the hardware system of the exoskeleton hand, including the circuit design of the driver, the fpga - based motion controller, the processing and the a / d conversion for the sensor signal

    其次，設計了外骨骼手底層控制系統的硬體電路，包括微型驅動器模塊電路的設計，基於fpga的運動控制器電路的設計，傳感器信號調理以及模/數轉換電路的設計。
  17. The elastic moduli eijlm represents a tensor of the fourth order.

    彈性模數Eijlm表示一個四階張量。
  18. Those include power supply circuit design ; ground plane design and sample clock design. combining some radar development, its high - speed a / d circuit is tested, and has given out some test results

    最後結合某雷達研製，對其高速模數轉換電路設計進行了實際測試評估，並給出了部分測試結果。
  19. Such as harmonic distorted in front analog circuit, sample clock shaking, analog power and the noise in ground plane etc. some suggestion of circuit design is given to improve high - speed a / d circuit performance

    在高速模數轉換電路的應用設計中地電源供電設計、模數地平面設計、采樣時鐘設計等方面提出一些具有指導性的意見。
  20. As it is impossible to machine the helicoid gear surface with large module and a few teeth by gear generating, a four - axis milling was developed in this paper

    摘要針對大模數少齒數螺旋齒輪的加工特點，結合漸開線和擺線的性質，利用微分幾何工具計算出該類曲面的法矢，作為選取球頭銑刀半徑的依據。
分享友人
分享到 Line

分享到臉書