模板夾具 的英文怎麼說
中文拼音 [móbǎnjiājù]
模板夾具
英文
form clamp-
The new technique allows first order shear deformation plate theory ( fsdpt ) or classical plate theory ( cpt ) to be used for modeling built - up wing structures, sandwich wing structures or the wing structures which the volume between upper and lower skin is empty or solid with a ' general planform
根據翼面的幾何和結構特點,新技術能夠自主選擇經典板理論( classicalplatetheory ,簡稱cpt )或第一階剪切變形板理論( firstordersheardeformationplatetheory ,簡稱fsdpt ) ,具有模擬空心、實心、夾層和組合等形式的翼面結構及三維建模的能力。Sealing and sliding sealing rings, cutting tools, reamer tips, reamer heads, saw tips, clamping supports, inserts for bore - crowns, plates, tip inserts for measuring and testing devices, nozzles, lining bushings, milling inserts, cold rolls, drawing dies, powder pressing dies
密封環和滑動密封環、切削工具、絞刀齒、絞刀頭、鋸齒、夾具、牙冠填充物、金屬板、測量和試驗儀器的頂端襯墊、噴嘴、襯套軸套、銑削襯墊、冷壓模具、沖模、粉末壓模。This thesis mainly researches second - prestressing precast slabs, it is important to study its one - way slab floor ' s ability in use. specific content include : imitate construction load lab, through this method to analyze the precast slabs " properties in the first stage in burden load. one - way precast slabs " lab, analyes one - way precast slabs sandwich s ability in second burden load stage
具體的研究內容有:模擬施工荷載試驗,即對裝配整式夾層板第一受力階段進行研究;單向裝配整體式結構的第二受力階段的性能進行研究,並分析了二次張拉預應力筋所引起的結構的變形和應變與計算結果進行對比。In some cases, instead of a cast, a splint made of plastic or metal will be secured over the area to restrict movement
某些情況下可以使用塑料或金屬夾板代替模具,用以保護受傷部位限制行動。First, according to the demand of vimp for resin system, the reaction kinetics and rheological of up resin are investigated and the optimal content of low additive profile ( lpa ) is determined. then vimp based on a high - permeable medium and grooves are studied by visual experiments, through which the appropriate high - permeable mediums are selected and the parameters of width, depth and spacing for flow grooves and spacing for supply grooves are optimized. furthermore, various factors affecting the mold filling process are discussed and the whole vacuum infusion procedures are described taking examples of the manufacture of a model boat and a sandwich panel in one infusion
文中首先根據vimp對樹脂體系的要求,對vimp用不飽和聚酯樹脂體系的動力學和流變學性能進行了研究,確定了最佳低收縮添加劑的含量;對高滲透介質型和溝槽型vimp開展了實驗研究,通過可視化實驗優選出較好的高滲透介質,確定了引流槽的寬度、深度和槽間距及主槽的槽間距等工藝參數並進行了優化;對影響充模過程的各種因素進行了詳細的討論,並以模型船和夾芯面板的製作為實例描述了兩種vimp的成型過程;在實驗的基礎上,建立了二維滲漏模型,採用控制體有限元法對高滲透介質型vimp進行了成型過程的計算機模擬計算,通過充模時間和流動前峰的計算值與實驗結果的比較,驗證本文所採用的數學模型和數值方法的正確性,其結果對實際生產具有一定的理論指導意義。分享友人