模腔充料 的英文怎麼說

中文拼音 [móqiāngchōngliào]
模腔充料 英文
cavity filling
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 腔 : 名詞1. （動物體內空的部分） cavity; chamber 2. （話） speech 3. （樂曲的調子） tune; pitch 4. （說話的腔調） accent; tone
  • 充 : Ⅰ形容詞（滿; 充足） sufficient; full; ample Ⅱ動詞1 （裝滿; 塞住） fill; charge; stuff 2 （擔任; ...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  1. The metal flowing pattern of the tooth filling process at different stages during closed die extrusion is found through lead deformation test and double - acting extrusion method on a doubled - acting press or on a special die structure with a general press is proposed

    成形試驗獲得了金屬充填齒形腔的流動模式，提出採用專用雙動壓力機或在通用壓力機上採用特殊模具實現坯料雙向擠壓的成形方法。
  2. Find the law of the influence from the injection pressure to the filling time and the cavity pressure and make certain of the best filling time, injection time and injection pressure. though the analysis of the flowing velocity and pressure spread of the key position element in the injection parts in different gate position, we forecast the injection parts quality and the possibility injection flaw and its position, optimize the gate position. in this paper, though the research of analogue of the runner system of metal - powder injection molding and the process of injection molding, we get the law of how the injection parameter influence the injection process

    在相同的注射條件下，通過分析喂料在不同直徑和長度流道中的流動規律，得到了喂料在流道中的速度場、壓力場和溫度場，找到了流道長徑比的合理取值范圍，並得出通過改變流道設計可實現對現有設備資源充分利用的結論；給出了不同注射壓力下，型腔壓力與充模時間關系曲線和喂料熔體平均充填速度與充模時間關系的曲線，得到了注射壓力對充填時間和型腔壓力的影響規律，確定了最佳的充模時間、注射時間和注射壓力；通過分析採用不同位置澆口注射時注射件關鍵位置單元的流動速度和壓力分佈，預測了注射件的成形質量，或可能產生的注射缺陷及位置，優化了澆口設置。
  3. Firstly, the comparation study between the wedge pressing and the contour forging has shown that the transverse deforming initiated from the surface of the preforms. when the superficies reached the moulding wall, the deforming moved downwards as the high - direction deforming increased, till the moulding chamber was full of stock ; the transverse deforming of the moulding pressing stock initiated from the center of the stock then surned into a drum - type. the distribution of the density and hardness of the high - direction indicated that the wedge pressing acquired a better ability of pressing penetration

    首先對比研究了楔形壓制工藝與模壓緻密化工藝，發現楔壓坯料的橫向變形從上表層開始，當上表面與模壁接觸后，隨著高向變形量的增加逐步向下移動，直至坯料充滿模腔;模壓坯料的橫向變形從坯料中間開始，形成鼓形。高向的密度、硬度分佈表明楔壓比模壓具有更好的壓透能力。
  4. Because modeling the material heat output air and the molding tool cavityinside gather together quickly output of burnt, flow the mark, lack to anticipate, inhale to result in of transform the etc., the blemish can get to solve well

    由於成型材料高溫產生的氣體和模具腔內快速集聚產生的燒焦、流痕、缺料、吸氣造成的變形等缺陷能得到充分解決。
  5. Abstract : in this paper, a kind of technological scheme for one - step precision forging spur gear with large module is put forward by using positive friction role. experiment, in which commercial pure lead is taken as test material, is done in the special die designed, and force vs. stroke curve is recorded. it is shown that positive friction role can efficiently make a contribution to the filling of the tooth cavity, but increase forming force

    文摘:針對大模數直齒圓柱齒輪，提出了利用積極摩擦一步成形的工藝方案，並用工業純鉛作為試驗材料，在設計的專用模具上進行試驗，記錄了力? ?行程曲線，結果表明：利用積極摩擦作用能夠有效地保證直齒圓柱齒輪精鍛時齒腔充滿，但同時增加了變形力。
分享友人
分享到 Line

分享到臉書