模頭 的英文怎麼說

中文拼音 [mótóu]
模頭 英文
die head
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  1. The driving rollers are electroplated with hard cr, tension self - controlling of winding - rollers are applied to the driving unit. the barrel of extruder, bullhead tee and die adopt cast aluminum heater which is endurable

    擠出機料筒三通和模頭均採用鑄鋁加熱，牽引輥筒電鍍硬鉻，輪鏈輪採用
  2. Calculatie retention time of plastic melt in extrusion moulding head

    塑料熔體在擠出模頭中停留時間的計算
  3. Main product : one - lay film puffing extrusion machine with a revolving head, double - lay / three - lay co - extrusion production machine with a compound revolving head, up - drawing rotary film production line, up - drawing rotary film production line for ibc ( internal bubble cooling )

    主要的生產設備有：單層旋轉模頭吹膜生產線，二層/三層共擠復合旋轉模頭吹膜生產線，上牽引旋轉吹膜擠出生產線，上牽引旋轉膜泡內冷吹膜擠出生產線。
  4. Slowly increase the temperature, starting from the die and then from the last to the first zone

    慢慢提高溫度，從模頭開始，然後從最後加工段向第一段。
  5. Specially design co - extruding die, merely need to replace core mandril, it may produce solid - wall pipe, solid wall inner helix pipe foamed pipe and foam inner helix pipe

    特殊設計的共擠模頭，只需要換芯棒即可同時生產實壁管、實壁內螺旋管、發泡管、發泡內螺旋管。
  6. Study on various designs for coat - hanger die

    衣架型模頭設計理論的研究
  7. Inclined transfer single double - die head single double - die stand hydraulic automatic hollow molding machine - model zxxc

    斜移式單雙模頭單雙模架液壓全自動中空成型機型號zxxc
  8. No. of heating section of mold head

    模頭加熱段數
  9. Electric cabinet as well as control cabinet in the sub cabinet, containing all controls such as two temperature controllers, on / off push buttons for blower, film drives, lamp and pneumatic opening / closing of nip rolls. the film attachment is equipped with it ’ s own electric supply so that the die and flange can be heated up even when removed from the extruder

    電氣櫃帶有所有控制模塊包括兩組溫度控制器，吹膜機開/關按鈕，光源和夾緊輪的氣動張開/閉合控制。薄膜附加設備帶有自己的供電模塊，因此即使同擠出機分開也可以將模頭和法蘭單獨加熱。
  10. As this is a tight fitted pe which was temporarily reduced by 10 % of its original od through a special die before lined into the old system, which the pe pipes resumed the original od after release of tensile force

    由於這是緊配合的聚乙烯襯管，在放入原來管道之前，原外徑暫時用專用模頭減少10 % ；當拉伸力釋放后，聚乙烯管道恢復原有的外徑尺寸。
  11. This function block fem simulation can be used in profile die design, so a new design method of function block comes forth

    完成以上步驟后，將上述過程運用於擠出模頭中功能塊結構的設計計算，探討出一種功能塊設計的新型流程的方法。
  12. The centre enters the material, the pushing out of the mould head of many patterns, remove and make and converge the line completely, meet the demands of different structure products

    中心入料，多型式的擠出模頭，徹底清除製品匯合線，滿足各種結構製品的要求。
  13. Operational equipmnt double winder 、 die rotating device 、 tension auto control system 、 plc control system 、 air shaft 、 auto unloader device 、 two or three - layer coextrusion blownand etc

    特殊配置雙收卷機、旋轉模頭、自動張力控制系統、 plc可程式控制系統、氣壓收卷軸、自動卸料裝置、二至三層共擠。
  14. Two digital self - tuning temperature controllers, one for film die and the other for the flange for the extruder. the controllers are mounted on the sub cabinet to the film tower

    兩個數字式自旋轉溫度控制器，一個用於薄膜模頭另一個用於擠出機法蘭。控制器安裝在吹膜塔的控制櫃中。
  15. Fix upper and lower blocks on the die with m16 screws

    用m16的螺絲將上下壓塊固定在模頭上。
  16. As shown, pressure increases both at the die and in front of the screen system may be 50 % to 160 % higher than typical operating pressure for higher usage levels

    如上所示，在大劑量使用擴鏈劑時，在模頭和濾網系統前端的壓力可能估比通常的操作壓力高出50 %到160 % 。
  17. This the production thread application plc carries on procedure control, and realizes to crowd out machine owner ' s electrical machinery and synchronization towing the mechanical and electrical machine is transferred fast ( ly ), and the installation has the good man - machine interface, and all technology parameters all can be set up and show by way of touching the screen, and producing to consult the menu, the order name was formerly fixed in the input, and whole production line just can be according to primary pipe specifications and speed production fixing every time ; cutting the function voluntarily fixed long ( ly ) cuts, and a pattern head temperature is controlled to use the import intellect warm accuse table ( making the temperature deviation within ), therefore having pledged the quality of tube

    本生產線採用plc進行程序化控制，實現擠出機主電機、牽引機電機的同步調速，並設置有良好的人機界面，所有工藝參數均可通過觸摸屏進行設置和顯示，每次生產只需查閱菜單，輸入原先設定序號，整條生產線就可按原設定的管子規格和速度生產；切割機能自動定長切割，模頭溫度控制採用進口智能溫控表（使溫度偏差在1內） ，因此保證了管材的質量。
  18. Function and application of the bi - pentagonal extruding mould machine

    雙工位五層共擠雙模頭中空成型機的性能與應用
  19. Numerical simulation of polymer flow in the coat - hanger die of melt blown process

    熔噴非織造衣架型模頭中聚合物流動數值模擬
  20. The hydraulic automatic hollow molding machine traditionally called as blow molding machine is a professional, most economical, full automatic blow molding equipment especially designed with internationally advanced blow molding die head technologies for meeting customer needs

    本款液壓全自動中空成型機俗稱吹塑機是我公司引進國外先進吹塑模頭技術，按用戶要求定向設計的最合乎經濟效益的專用化全自動吹塑機設備。
分享友人
分享到 Line

分享到臉書