樣品槽 的英文怎麼說

中文拼音 [yàngpǐncáo]
樣品槽 英文
sample cell
  • 樣 : Ⅰ名詞1. （形狀） appearance; shape 2. （樣品） sample; model; pattern Ⅱ量詞（表示事物的種類） kind; type
  • 品 : Ⅰ名詞1 （物品） article; product 2 （等級; 品級） grade; class; rank 3 （品質） character; qualit...
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  • 樣品 : sample; specimen; prototype; exponent
  1. The silicon plates are formed reverse four wimble array in koh solution by wet - etching technology. then the electrochemical etching experiments are done in three poles electrobath. and some technology questions such as heat oxygenation, light etching, wet etching and electrochemical etching have been analyzed. at the same time sample appearances are analyzed by scanning electron microscope. according to current burst model theory, the electrochemical deep holes etching mechanism are analyzed

    在三極電解槽中，進行了電化學深刻蝕的探索性實驗。對氧化、光刻、濕法刻蝕和電化學刻蝕中的工藝問題進行了初步的理論和實驗研究，同時，採用sem對實驗樣品進行了形貌分析，並採用電流突破模型對電化學深孔刻蝕機理進行了理論分析。
  2. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
  3. Animal health analysis methods - control protocol of reagents control protocol of reagents for the detection of antibodies directed against brucellosis by the rose bengal test, the complement fixation test or the seroagglutination test in serum samples or for the detection of antibodies directed against bovine brucellosis by the ring test in bulk tank milk samples

    動物健康分析方法.用四碘四氯熒光素試驗補體結合試驗或血清凝集試驗檢測血清樣品中抗布魯氏菌病的抗體或用環試驗檢測收集槽牛奶樣品中抗牛布魯氏菌的抗體用試劑的試劑控制協議的控制協議
  4. Study method of sediment color reflectance in shelf has been established based on lots of investigative studies, obtained more than 7000 units of data of color reflectance using minolta cm - 2002 spectrophotometer from 165 cores in the yellow sea and the east china sea, illustrated the distributional rules of color reflectance in sediment of the shelf of south yellow sea, the shelf of north east china sea shelf and okinawa trough for the first time

    本論文基於大量的實驗研究，建立了陸架沉積物顏色反射率的研究方法。利用minoltacm - 2002光譜光度計測量了黃海、東海海區的165個巖心樣品，獲得了7000多個有效的顏色反射率數據，首次給出南黃海陸架、東海陸架北部、沖繩海槽等海區沉積物的顏色反射率分佈規律。
分享友人
分享到 Line

分享到臉書