樹脂澆鑄體 的英文怎麼說
中文拼音 [shùzhījiāozhùtǐ]
樹脂澆鑄體
英文
resin casting- 樹 : Ⅰ名詞1 (木本植物的通稱) tree 2 (姓氏) a surname Ⅱ動詞1 (種植; 栽培) plant; cultivate 2 (樹...
- 脂 : 名詞1. (動植物所含的油質) fat; grease; tallow 2. (胭脂) rouge 3. (姓氏) a surname
- 澆 : 澆名詞(姓氏) a surname
- 鑄 : Ⅰ動詞(鑄造) cast; coin; make Ⅱ名詞1. (古國名) zhu, a state in the zhou dynasty2. (姓氏) a surname
- 體 : 體構詞成分。
- 樹脂 : resin; jaffaite; peucine
-
Test method for impact resistance of resin casting body
樹脂澆鑄體沖擊試驗方法Abstract : using furan sand to produce heavy diesel engine block and crankshaft eliminated defects of castings including “ penetration / burn - in ”, “ shrinkage porosity ”, “ big dimension deviation ” of cylinder block, “ penetration / bum - in ”, “ misrun ” and “ run - out ” of crankshaft, and so on
文摘:樹脂砂鑄造工藝應用於大型球墨鑄鐵件整體鑄造柴油機缸體、曲軸生產上消除整鑄缸體「粘砂」 、 「縮松」 、 「尺寸偏差大」及曲軸「粘砂」 、 「澆不足」 、 「漏鐵液」等鑄造缺陷,具有明顯的效果。The generals of test methods for properties of resin casting body
樹脂澆鑄體性能試驗方法總則Test method for tensile properties of resin casting body
樹脂澆鑄體拉伸性能試驗方法Unsaturated polyester resin - determination of stability of casting resin in basic solution
不飽和聚酯樹脂澆鑄體耐堿性測定方法Standard general requirements for dry - type distribution and power transformers including those with solid - cast and or resin encapsulated windings
包括固體澆鑄和或樹脂密封繞組的乾式配電和電力變壓器的一般技術要求Test method for compressive properties of resin casting body
樹脂澆鑄體壓縮性能試驗方法Test method for compressive properties of
樹脂澆鑄體壓縮性能試驗方法Test method for flexural properties of resin casting body
樹脂澆鑄體彎曲性能試驗方法Characteristics of cured resin without reinforcement
樹脂澆鑄體性能:Charactertica of cured resin without enforcement
Hr 189xg樹脂澆鑄體性能Cured resin without reforcedment
樹脂澆鑄體性能( 2 ) the tensile, bend and impact ductility experiment of the resin cast with fsmf filler are employed
( 2 )進行了fsmf填充樹脂澆鑄體的拉伸、彎曲和沖擊韌性實驗。A full - scale review of the nonmetal mineral filler to improve the strength and toughness of the resin matrix materials in the domestic and overseas is presented. based on the theory and experiment, the mechanism of the fsmf filler to build up the strength and toughness in the resin matrix composite materials is studied ; the relation of the mechanical property of the resin cast and the content of the fsmf is obtained ; the elasticity modulus of the fsmf powder is estimated by analysis method and cmm method ; in the end, fsmf used in rpmp is discussed
本文對非金屬礦物填料填充樹脂復合材料增強增韌的國內外研究現狀進行了較全面的評述;在理論和實驗的基礎上,研究了fsmf填充樹脂復合材料增強增韌機理;進行了fsmf填充樹脂澆鑄體的有關力學性能測試,獲得了fsmf填充樹脂澆鑄體的有關力學性能與fsmf含量的關系;利用解析法和cmm法,估算了fsmf粉體的彈性模量;最後探討了fsmf在玻璃鋼夾砂管道中的應用。Guide for test procedures for thermal evaluation of insulation systems for solid cast and resin - encapsulated power and distribution transformers
固體澆鑄和樹脂密封的電力和配電變壓器絕緣系統熱評定試驗程序指南Standard method of torsion test for resin cast
樹脂澆鑄體扭轉試驗方法General requirements for dry - type distribution and power transformers including those with solid - cast and or resin - encapsulated windings
包括固體澆鑄和或樹脂密封繞組式在內的乾式配電和電力變壓器的一般技術要求Unsaturated polyester resin - determination of refractive index of liquid and casting
不飽和聚酯樹脂液體和澆鑄體折光率的測定Test method for impact resistance of resin
樹脂澆鑄體沖擊試驗方法The results show that fsmf can improve the bend modulus of the resin cast clearly, but reduce the tensile strength. in the suitable content of filler ( not more than 30 % in this experiment ), fsmf can improve the tensile modulus and bend strength. in the suitable content of filler ( 20 % ~ 30 % in this experiment ), fsmf can improve the toughness of the resin cast
結果表明: fsmf顯著提高樹脂澆鑄體的彎曲模量,但降低拉伸強度;在合適的填料含量(本實驗中為30 )下, fsmf可提高樹脂澆鑄體的拉抻模量和彎曲強度;在合適的填料含量(本實驗中為20 30 )下, fsmf可起到增韌效果,改善樹脂澆鑄體的斷裂韌性。分享友人