機器證明檢驗 的英文怎麼說

中文拼音 [jīqìzhèngmíngjiǎnyàn]
機器證明檢驗 英文
mechanical proof testing
  • 機 : machineengine
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 證 : Ⅰ動詞（證明） prove; verify; demonstrate Ⅱ名詞1 （證據） evidence; proof; testimony; witness 2 （...
  • 明 : Ⅰ形容詞1 （明亮） bright; brilliant; light 2 （明白;清楚） clear; distinct 3 （公開;顯露在外;不隱...
  • 檢 : Ⅰ動詞1 （查） check up; inspect; examine 2 （約束; 檢點） restrain oneself; be careful in one s c...
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 機器 : 1. （用來轉換或利用機械能的機構） machine; machinery; engine 2. （引申為機構） apparatus; organ
  • 證明 : 1 （表明 、 斷定真實性） prove; testify; bear out 2 （證明書或信） certificate; identification; t...
  • 檢驗 : checkout; test; examine; inspect; verify; survey; check;checking;testing;[英國]jerque（指檢查船舶...
  1. The structure of air - blast pipe was improved on. an orienting object was installed based on theoretical analysis, that increase the spraying span. it has been found that both spraying span and droplets uniformity improved, by installing the orienting object. according to the results of a great number of experiments, orderliness of droplets diameter along the spraying span was researched, and rational spraying span of air - assisted sprayer was suggested

    通過試驗檢驗噴霧機樣機的噴霧性能，並提出對各項參數的優化設計方案。通過正交試驗和對比試驗對霧滴取樣，證明導流器的安裝不僅增加了噴幅，而且還提高了霧滴均勻性系數。根據大量試驗的結果分析，找出了霧滴直徑在噴幅方向上所呈現的變化規律，並提出了合理的噴幅范圍。
  2. With the development of microelectronic products ( integrated circuit, printed circuit board, etc ) directing to high density, thin separation and low defect ratio, its inspection requirement is higher on aspects of precision, efficiency, universal, and intelligence etc. therefore, this paper researched on the general key techniques in the field of microelectronic products vision inspection, covered the shortage of traditional inspection on aspects of fast and precision locating, image mosaic, and fine defect test, completed theory study on physical dimension and defect inspection of microelectronic products based on machine vision, developed the prototype and used lots of experiments to prove its correctness and feasibility

    隨著微電子產品（集成電路晶元、印刷電路板等）向著高密度、細間距和低缺陷方向發展，對其檢測技術在精密、高效、通用和智能化等方面提出了更高要求。由此，本文對微電子產品視覺檢測中的關鍵技術進行研究，彌補了傳統檢測在精確快速定位、圖像全景組合和精細缺陷檢測等方面的不足，最終完成基於機器視覺的微電子產品外形尺寸和缺陷檢測的理論研究和樣機研製，並進行了大量實驗證明其正確性和可行性，力圖為我國自主創新的微電子產品視覺檢測技術提供理論和實際借鑒。
  3. The theory analysis and experimental result of oil barrel rust cleaned by high pressure water jet show that after the steel container is cleaned by water jet, its deep level structure rust does not affect the oil quality really, and does not product new mechanical impurities, and this clean way can clean various oil container in high quality

    摘要對經過高壓水射流清洗后的鋼油桶銹蝕進行了理論分析和試驗檢測，結果表明，鋼容器經過高壓水射流清洗后，深層次銹蝕對油品質量沒有實質影響，也不會產生新的機械雜質，該清洗方法能保證可靠的清洗質量。
  4. In chapter 4, the designed position sensor is experimentally tested. compared the result of position detection of the sensor with the stepper motor ' s actual trajectory, we get satisfactory result. it proves the feasibility of the method

    第四章，通過實驗，將所設計的傳感器的位置信號檢測結果與步進電機的實際運動軌跡進行了比較，並得到了較滿意的結果，證明了此方法的可行性。
  5. Fifth, with the comparison between results of simulation calculated and experimental results, the dynamic mathematical model in this thesis is proved to be reliable, correct and sensitive to some parameters. the results can be applied to system simulation

    同時也可實現對製冷系統從開機到停機全過程進行時時檢測和模擬； 5 ）通過比較蒸發器模擬計算結果和實驗結果，證明本文所建立的蒸發器動態數學模型的正確性和可靠性及對某些參數的良好敏感性，可用於系統模擬。
分享友人
分享到 Line

分享到臉書