橫切面積 的英文怎麼說

中文拼音 [héngqiēmiànjī]
橫切面積 英文
cross-sectional area
  • 橫 : 橫形容詞1. （蠻橫; 兇暴） harsh and unreasonable; perverse 2. （不吉利的; 意外的） unexpected
  • 切 : 切Ⅰ動詞1 （合; 符合） correspond to; be close to 2 （用在反切后頭 表示前兩個字是注音用的反切）見 ...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 積 : Ⅰ動詞（積累） amass; store up; accumulate Ⅱ形容詞（長時間積累下來的） long standing; long pending...
  • 面積 : [數學] area
  1. The large bowlder surface of dinner table must be uplifted vertically in avoidance of breakage. the small one shall also be held vertically instead of horizontally

    大面積的餐臺玉石面，必須豎抬，避免餐臺斷裂。小面積的玉石面也應豎拿，切忌平面橫抬橫拿。
  2. Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle

    流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。
  3. The proportion that the sediment yield of the main gully accounts for the total sediment yield of the experimental watershed model is from48. 7 % to 66. 6 %, and the proportion that deposition sediment yield of main gully accounts for the total deposition sediment yield of the experimental watershed model is from64. 9 % to 99. 4 %. the developing process of topographic feature of the experimental watershed model. expanding the gully width and cutting down the gully bottom are the two chief forms of the topographic feature development

    流域模型地貌形態發育過程溝谷擴展和下切是流域模型地貌形態發育的主要形式，溝谷擴展發育主要發生在發育活躍時段，主溝所佔溝谷總面積比例在流域模型溝谷擴展發育過程中保持在60以上：主支溝下切發育在發育初期和發育活躍時段前期表現最為劇烈，其橫剖面為v字形，在發育初期和穩定時期時段呈現淺u字形和底部較為平坦的梯形，主溝的橫剖面發育明顯優先於各支溝。
  4. The degree of self - induction is proportional to the cross - sectional area of the circuit

    而自感的程度與線圈橫切面的面積成比例。
  5. And the impact of every parameters of f - ved element, stiffness coefficient and damper coefficient of ved element, normal stiffness, tangent stiffness and sliding friction of frd element and the cross - section area of the brace on the capability of dissipating vibration energy is computed and analyzed

    並對f - ved單元中ved單元的剛度系數、阻尼系數、 frd的法向剛度、切向剛度、滑動摩擦力及支撐橫截面面積等參數對單元阻尼效果的影響進行了分析研究。
  6. Chip cross - sectional area

    切屑橫截面面積
  7. Planation surface is a wide - ranging and undulating surface formed by planation in a long and relative stable period or in a decreacing - development period. it is near the base level and there always exists some deposits such as crust of weathering above it. planation surface is often uplifted or buried by the later tectonic activities

    夷平面是在長期的地殼相對穩定時期或地殼下降發展階段，由廣泛的夷平作用以截斷面形式橫切所有先成的地層和構造的接近侵蝕基準面的平緩的地表形態，其上常有風化殼等碎屑堆積，常遭到後期的抬升切割或埋藏，分佈於地球的各緯度帶。
分享友人
分享到 Line

分享到臉書