橫向桿 的英文怎麼說

中文拼音 [héngxiànggǎn]
橫向桿 英文
transverse bar
  • 橫 : 橫形容詞1. （蠻橫; 兇暴） harsh and unreasonable; perverse 2. （不吉利的; 意外的） unexpected
  • 桿 : 桿名詞（桿子） pole; staff
  • 橫向 : broadwise; infeed; crossrange; abeam;transverse; transverse direction; cross; crosswise; lateral;...
  1. In this system, the oil pipe be locally magnetized through the longitudial and circumferential direction, the oil pipe be circumvolved by the electromotor, the detector will has a linear movement on the surface of the pipe, so it can realize the combined testing of horizontal flaw ( cankerous pits and cankerous holes etc. ) and vertical flaw ( pole flaw and crack etc )

    該系統在油管局部實施軸向和周向磁化，油管由電機主軸帶動旋轉，檢測探頭緊貼油管直線運動，從而實現對腐蝕坑、腐蝕孔等橫向缺陷和桿狀損傷、劈縫等縱向缺陷的綜合檢測。
  2. In order to considering the affections of the adjacent zone out of the girdler section, the internal - forces of two end surface which were obtained by the horizontal shaft system analysis are exerted on each model respectively. moreover, the weight, cable force and prestressing forces including girder longitudinal, diaphragm transverse and inclined web vertical directions are considered

    考慮到梁段以外附近區域的作用，在其兩端面上施加了由平面桿系結構分析所得的端面內力，另外，索力和預加力（梁縱向、橫隔梁橫向、斜腹板豎向）也施加在相應的位置，分析了箱形主梁在自重、索力和預應力作用下的空間應力效應。
  3. The mechanism consists of a steering gear box, pitman arm, drag kink, tie rods, steering arms, and steering knuckles, the latter supporting the front wheels

    該機構由轉向器，轉向垂臂，縱拉桿，轉向橫拉桿，梯形臂和轉向節構成，轉向節支承著前輪。
  4. Specifically, the 3 - roll calender is fed by a conveyor belt transversally sliding through the rolls and by a 2 - stage planetary extruder complete with thermoregulation units

    具體的說， 3輥壓延機由一個沿輥子橫向滑動的輸送帶和一臺帶有控溫裝置的2段行星螺桿擠出機喂料。
  5. Bt insulators and fittings for overhead lines. metal fittings. pole top cross arm

    架空線路用絕緣子和配件.金屬配件.桿頂橫向臂
  6. Those sensitive parameters making system have negative damping and occur self - excited shimmy are horizontal pulling lever rigidity, tire sideslip rigidity, steering gear rigidity and damping, kingpin equivalent damping, kingpin caster angle, tire drag. and wheel center distance, tire side rigidity, vehicle wheel unbalanced mass, tire vertical rigidity, and distance from kingpin center to the vertical central line plane of tire have great influence on shimmy, but they do n ' t make the system have negative damping. and horizontal pulling lever damping, suspension damping and rigidity have very small influence on shimmy

    橫拉桿剛度、輪胎的側偏剛度、轉向機剛度、轉向機阻尼、繞主銷當量阻尼、主銷后傾角、輪胎拖距是影響擺振的敏感性參數，適當調節某一參數可引起系統的負阻尼，使系統產生自激擺振；輪距、輪胎側向剛度、車輪上的不平衡質量、輪胎垂向剛度及主銷延長線與地面交點至車輪平面的距離對擺振的影響也較大，但不會使系統出現負阻尼；而橫拉桿阻尼、懸架阻尼與懸架剛度對擺振的影響很小。
  7. The highlights of this paper include : hoop toughness criterion for longitudinal heat checking of tool joint was introduced firstly ; failure criterion for crescent - shaped wear casing was established according to the results of full - scale collapse tests ; new - typed alloy for hardbanding of tool joint was developed, its property has showed good performance in the tests

    本文的主要創新點在於：以現場失效案例分析為基礎，提出了鉆桿接頭縱向熱裂的橫向韌性判據；通過對已磨損套管的實物擠毀試驗研究，確定了不均勻磨損套管的擠毀失效準則；設計出了具有獨立知識產權的鉆桿接頭硬化帶用新型耐磨減摩合金的成分，經實驗室試驗表明其性能可以達到或超過國外同類產品。
  8. The software ansys6. 0 is used to analysis the stability of the state after construction of tongwamen bridge, linear method is used in analyzing the finite element model of the bridge, the coeffient of stability of different state after construction is given. on the basis, the effect of different factors such as the arrangement of lateral brace, the sloping angle of arch ribs, the stiffness of bridge deck system, the effect of non - orientedly conservative loadings of the hanger and tie bar etc is discussed. the different coefficients of stability of changing these factors are given, so the factors that are vital to the lateral stability of x - type arches are found, and the rationality of the methods taken to enhance the lateral stability of tongwamen bridge is evaluated

    本文應用有限元分析商業軟體ansys6 . 0 ，採用線彈性方法，通過對該橋的空間有限元模型進行穩定性分析，得出其成橋運營階段各種工況下的穩定安全系數。在此基礎上，本文還通過有限元模型分析，就拱的矢跨比、吊桿（立柱）的非保向力效應、橋面系的剛度、橫撐布置形式、拱肋側傾角等因素對該橋整體穩定性的影響展開探討與研究。文中給出了各因素變化情況下的穩定安全系數，指出了對鋼管混凝土提籃拱橫向穩定性有顯著影響的因素及其合理變化范圍，並對銅瓦門大橋提高橫向穩定性的措施的經濟合理性進行了分析。
  9. The harmonic analysis method for computing force of end - point of variable cross - section beam when it does transverse vibration

    計算變截面梁橫向振動時桿端力的調和分析法
  10. Research on lateral pressure in truss rod for support of loose roof

    錨拉支架支護散體頂板時拉桿的橫向受力研究
  11. Generally, the skew bridge ' s calculation theories can be divided into three types : the category 1 is the plank theories method, such as the finite difference method, the finite element method and the finite strip method, etc ; the category 2 is the beam theories, such as the grid beam theories, the general grid theories, the rigid cross - beam method, the elastically - supported continuous beam method and the bar system analytical method, etc ; the category 3 is the practical method, such as the g - m revising method, the grid - beam simple method and ghali form coefficient method, etc

    目前關于斜梁橋的計算理論和方法概括起來，大致可以分為三類：第一類為板理論方法，如有限差分法、變分法、有限單元法、有限條法等；第二類為梁理論法，如格構梁理論、一般格構理論、剛性橫梁法、彈性支承連續法、桿件結構的分析方法；第三類為實用計演算法，荷載橫向分佈的計算方法如g ? m修正法、格構梁的簡易法、 ghali表格系數法等。
  12. With the actual locale incestigating, the actual locale testing and the theories analyzing of the reason of the diseases producing of the exceed limit of horizontal swing and steel pole ' s break, and summaried the reinforcing measure of the top bear armor plate beam

    通過對京廣線鄭州黃河大橋40米上承式鋼板梁橫向擺動嚴重超限及鋼梁桿件斷裂等情況的現場調查、現場測試和理論分析及病害原因產生的機理，總結提出了上承式鋼板梁的加固措施。
  13. Firstly, for the system of moulding board and support frame in construction the side pressure and screws are analyzed. the material and structure form of support frame are discussed. the design of support frame uses the method of limited state, and also it analyses the integer stability, part stability, and single stability, and then proposes the load analysis of multi - level support frame

    首先，針對轉換層梁模體系及支撐架施工，重點分析了轉換層結構現澆混凝土對模板側壓力值及模板對拉螺桿的計算；討論了轉換層支撐體系的形式及構造，詳細論述了基於極限狀態設計的支撐架計算方法，包括縱橫向水平桿的強度驗算、立桿的整體穩定性、局部穩定性、單肢桿件穩定性等驗算，並提出了多層支撐架的施工荷載計算方法。
  14. The influence upon the fatigue stress of longitudinal bracing rods due to the transverse vibration of steel bridges

    橫向振動對鋼板梁橋聯結桿件疲勞應力的影響
  15. Based on the perturbation riccati transfer matrix method, the calculating program are developed. the program can be used to the perturbation analysis and the sensitivity analysis of the real and complex, the single and repeated eigenvalues and eigenvectors for lateral vibration of rod and beam structures, especially suitable to the perturbation analysis and the sensitivity analysis of eigenvalues and eigenvectors for rotordynamic systems ; 2. the perturbation riccati transfer matrix method was applied to identify the parameters of the rotor for a boiler supply pump, and the accurate dynamic model of the rotor was archived

    該程序可以對桿、梁結構橫向彎曲振動的實數、復數的孤立和重頻特徵值問題進行攝動分析和靈敏度分析，特別是適合於轉子動力學系統特徵值和特徵向量問題的攝動分析和靈敏度分析； 2 、用攝動riccati傳遞矩陣方法解決了某電站鍋爐給水泵轉子的參數識別及動力模型修改的問題，並給出了該種型號的給水泵轉子的更準確的力學模型，為進一步的轉子動力學分析與設計奠定了可靠基礎； 3 、給出了攝動理論在相關領域如隨機特徵值分析、隨機振動響應分析、可靠性分析、靈敏度分析、優化設計以及參數識別中的應用公式。
  16. Lateral buckling analysis of thin - walled members by finite member element method

    橫向荷載作用下薄壁桿件穩定分析的有限桿元法
  17. The kinematic performance of the macpherson suspension on a real vehicle is studied, and the changes of the front wheel alignment and the motion of the front wheel in the longitudinal and the transversal directions are figured. based on the requirements of general layout, a constrained optimization design model is set up with the steering cross rod ball joint position as the optimization variables ( design parameters ), and the sum of steering cross rod length interference while the left front wheel turning and bouncing as the objective function. and the optimization results are worked out by programming on computer

    針對一種實際車型上的麥弗遜式懸架，計算分析了轉向輪跳動時前輪定位角和車輪橫向、縱向滑移量的變化情況，並根據實際車型上麥弗遜式懸架的空間布置要求，建立了以轉向橫拉桿斷開點空間位置坐標為優化變量，轉向橫拉桿斷開點空間布置坐標可變化范圍為約束條件，車輪轉向和跳動時轉向橫拉桿長度干涉量為目標函數的約束優化設計模型。
  18. The influence analysis is achieved for maneuverability and stability of the coach - bus while the angel stiffness of it ' s lateral stable pole or the position of gravity center is changing

    並討論了橫向穩定桿角剛度變化、重心位置變化對大客車操縱穩定性的影響。
  19. Especially for the longitudinal heat checking of tool joint, the hoop toughness criterion of tool joint material was put forward to prevent the heat checking. based on analysis for field failure cases, minimal hoop impact work by means of mechanical calculation has been obtained, which can be used to modify the relevant contents of api rp7g

    特別針對鉆桿接頭縱向熱裂問題，提出了控制接頭材料的橫向韌性判據，並以現場失效案例分析為基礎，經力學計算初步確定了最低橫向沖擊功要求，可用於完善修訂apirp7g推薦做法的有關內容。
  20. To solve the problem the technology used by the elements of the program are : vertical flat steel welding between the horizontal poles of a number of encryption steel, the steel mesh grid formation plate

    解決該問題所採用的技術方案要點是：縱向的扁鋼之間的橫向桿上焊接若干加密鋼條，形成網狀的鋼格板。
分享友人
分享到 Line

分享到臉書