橫向長度比尺 的英文怎麼說

中文拼音 [héngxiàngzhǎngdùbǐchǐ]
橫向長度比尺 英文
lateral length scale
  • 橫 : 橫形容詞1. （蠻橫; 兇暴） harsh and unreasonable; perverse 2. （不吉利的; 意外的） unexpected
  • 長 : 長Ⅰ形容詞1 （年紀較大） older; elder; senior 2 （排行最大） eldest; oldest Ⅱ名詞（領導人） chief;...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 比 : Ⅰ動詞1 （比較; 較量高下、 長短、距離、好壞等） compare; compete; contrast; match; emulate 2 （比...
  • 尺 : 尺名詞[音樂] （中國民族音樂音階上的一級 樂譜上用做記音符號 參看「工尺」） a note of the scale in ...
  • 橫向 : broadwise; infeed; crossrange; abeam;transverse; transverse direction; cross; crosswise; lateral;...
  • 長度 : length; longitude; size; extent; footage
  1. With plating time going on, the nano - polycrystal gathering grows in two dimensions, and the new nano - polycrystal layer appears simultaneously on the formerly formed nano - polycrystal surface. because the boundary and defect densities in quenched and tempered 45 steel is higher than those in annealed steel, the nano - polycrystal gatherings formed at its surface at the beginning of electro - deposition are more concentrated, and then their size is smaller. the microstructure of the ni - p alloy coating has closed relation with its phosphorus content with the increase of phosphorus content, the microstructure of coating turns from nano - crystalline to the amorphous

    隨著施鍍時間的延長，納米晶聚晶體在橫向二維生長的同時，在納米晶聚晶體的表面上也進行著三維方向的新的一層聚晶體的生長；在調質態45鋼表面，由於其具有比較高的晶界和缺陷密度，因此在沉積初期，納米晶聚晶體的成核密度也較大，從而在二維方向聚晶體的尺度較小，鍍層沉積初期表現為緻密細小的鱗片狀組織。
  2. After comparing between the finite - element analysis and experimental results, the author verified the fem. then according to the chinese code, the nonlinear finite model of the beam - to - column is established which are made of different size components. the responses of beam - to - column web moment connections which are made of different size components are compared and analyzed from three facets, and the conclusions about the joints behavior are drawn : thicken the connection plate, lengthen the connection plate or use a back - up stiffer can improve the connection behavior, consist of improving the behavior of load - supported and reducing the stress convergence in the flange moment plates

    本文根據我國規范的有關規定，自行建立了12個不同構件尺寸的樑柱腹板連接的三維有限元模型，對不同構件尺寸的樑柱腹板剛性連接節點在單向荷載作用下的反應進行了研究，從結構的mises應力等值線示意圖、梁端加載處的荷載? ?位移曲線、翼緣連接板兩端的mises等效應力以及翼緣連接板與柱相連接的三邊的mises應力等值線示意圖四方面進行了比較與分析，從而得出了不同構件尺寸的樑柱腹板剛性連接的在受力行為上的結論：增加翼緣連接板的厚度、增加翼緣連接板的長度以及採用柱的橫向加勁肋均可以改善節點的受力性能：提高節點的承載能力；減小翼緣連接板內部與柱翼緣邊的的應力不均勻現象，從而避免試件過早地發生破壞。
分享友人
分享到 Line

分享到臉書