橫縫焊接 的英文怎麼說

中文拼音 [héngfénghànjiē]
橫縫焊接 英文
welding of transverse seam
  • 橫 : 橫形容詞1. （蠻橫; 兇暴） harsh and unreasonable; perverse 2. （不吉利的; 意外的） unexpected
  • 縫 : 縫名詞1. （接合處） seam 2. （縫隙） crack; crevice; fissure; slit
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  1. As an application of this fem preprocessing system, the simulation on the welding process of missile ’ s oil box was performed, in which the effects of the welding sequences of four web plates and welds on each web plate are primarily analyzed. the simulation results show that the deformations under varied welding sequences are almost the same. downward deflection deformation is obtained along the weld longitudinal direction in the structure as well as upward deflection deformation along the weld traverse direction

    對于某型號導彈油箱結構焊接過程的數值模擬計算，主要考察了每塊立板上各段焊縫焊接順序的調整、四塊立板之間不同的焊接順序以及焊接起始端的選擇對結構焊后變形的影響規律，模擬結果表明:壁板在各種焊接順序下的整體變形規律基本相似，即焊後壁板沿焊縫縱向發生了向下的撓曲變形，中部向下變形量最大;沿焊縫橫向發生了向上的撓曲變形，壁板兩端部變形量較大，且壁板前端變形大於壁板後端。
  2. Welding of transverse seam

    橫縫焊接
  3. Welding position : if the configuration collocation of weld is symmetry and the welding sequence is reasonable, the longitudinal contraction and transverse lateral contraction deformation are usually produced, incontrast, the bending deformation is usually produced

    焊接位置：如果焊縫在結構布置對稱，焊接順序合理時，則主要產生縱向收縮和橫向收縮變形，反之，則要發生彎曲變形。
  4. The other way, theoretical analysis of weld tracking system with a leading sensor is stated, based on the analyzing of movement process of the tracking system, a loop control structure diagram is presented, the deuce vision feedback system is used and realized the repeated and automatic tracking in multiplayer seam and controlling of system of tracking and system of motion

    同時就傳感器超前檢測式焊縫自動跟蹤系統進行了深入的理論分析，在分析該系統跟蹤過程運動關系的基礎上，建立了系統的閉環控制關系圖，並提出了其系統數學離散控制結構簡化圖。採用兩點式視覺伺服反饋系統，實現機器人在多層多道焊接時的重復自動跟蹤以及跟蹤機構的控制和焊炬橫向調節機構的控制，並使之協調聯動，滿足焊接過程的要求。
  5. Ys automatic girth welder ( ys - agw - i / ii ) is mainly used in horizontal girth inside / outside welding of large tanks 、 vessel etc. the welder applies submerged arc welding

    型埋弧自動橫焊機採用埋弧橫向焊接工藝，主要用於大型儲罐、容器等內外環縫的焊接
分享友人
分享到 Line

分享到臉書