止裂設施 的英文怎麼說

中文拼音 [zhǐlièshèshī]
止裂設施 英文
crack arrester
  • 止 : Ⅰ動詞1. （停止; 攔阻） stop; cut out 2. （截止） close; end Ⅱ副詞（僅; 只） only; just Ⅲ名詞（姓氏） a surname
  • 裂 : 裂動詞[方言] （東西的兩部分向兩旁分開） open
  • 設 : Ⅰ動詞1 （設立; 布置） set up; establish; found 2 （籌劃） work out : 設計陷害 plot a frame up; fr...
  • 施 : Ⅰ動詞1 （實行; 施展） execute; carry out 2 （給予） exert; impose 3 （施捨） give; hand out; best...
  • 設施 : installation; facilities
  1. In this paper, the reason and process of hot tear forming for the investment steel castings are analysed, the technological method of preventing hot tear is discussed, and the designing method of the self - cut - gate for shifting hot tear is introduced

    分析了熔模鑄鋼件熱裂產生的原因和過程，論述了防止熱裂的工藝措施，並介紹了自割內澆口轉移熱裂及其設計方法。
  2. Used to concrete seam and arbitrarily shape seam in component. in the condition of the expanding being favorable limited, attain satisfied stop - water effect and manage the concrete interstitial leaking. at the same time, it can be also used to shipping and engine etcindustrial equipment

    適用於現場澆注的混凝土施工縫和嵌入構件任意形狀的接縫內，在其膨脹受到良好限制的條件下達到滿意的止水效果，治理混凝土裂縫的漏水，同時也用於船舶、機車等工業設備的防水密封。
  3. In the article, we simply discuss the situation of deaerator vessel weld cracking in the power plant and analysize the reason of deaerator vessel weld cracking in detail. in the end, we discuss the problems that should be paid attention to give some ideas to prevent from cracking of the weld

    簡述了目前火電廠中除氧器水箱焊縫裂紋的特點，分析了裂紋產生的原因，並提出了在結構設計、安裝製造及運行管理中應注意的問題和採取的防止措施。
  4. Abstract : the article analyzes the influence of failure of heat treatment process and equipment for mn13 steel join, and offeres the method of preventing the part slitting and brittle cracking

    文摘:分析了熱處理工藝和設備對高錳鋼端頭缺陷的影響，提出了防止高錳鋼端頭脆性開裂的措施。
  5. Then the formu1a of computing the maxima1 top shear stress in designing masonry bui1dings and the method of checking computations of cracks are brought forward in this paper on the basis of the theoretica1 deduce and the data of these tests and experiments. a1so, the practica1 construct methods and the requirements of preventing such cracks in the aspects of the construct rate. the strength and modulus of e1asticity of the masonry bui1dings are put forward

    隨后，本文在理論推導和試驗數據的基礎上，提出了在砌體結構設計中計算頂層最大剪應力的公式和是否開裂的驗算方法，並且從施工進度、砌體的強度及彈性模量、構造柱和圈樑的設置等方面提出了防止此類裂縫開展的具體施工方法和要求。
分享友人
分享到 Line

分享到臉書