殘余功率 的英文怎麼說

中文拼音 [cángōng]
殘余功率 英文
residual power
  • : Ⅰ形容詞1 (不完整; 殘缺) incomplete; deficient 2 (剩餘的; 將盡的) remnant; remaining 3 (兇惡...
  • : Ⅰ動詞(剩下) remain; leave: 9減4 余 5。 nine minus four is five ; four from nine leaves five ; i...
  • : 名詞1 (功勞) exploit; merit; meritorious service [deed]: 戰功 military exploits; 立功 render me...
  • : 率名詞(比值) rate; ratio; proportion
  1. The nonlinear filtering for nbi estimate - subtract assumes that the prediction error is dominated by spread spectrum signal and the background noise power is far below spread spectrum chip power, this assumption promises the low error ratio of chip decision but may not be attainable to digitalized dsss receiver in military communication environment, and does not coincide with the principle of dsss communication that decreases bit error ratio ( ber ) depending on spread spectrum gain, not on chip power

    在干擾估計抵消濾波中,以往的非線性濾波要求干擾抵消濾波后擴頻信號遠大於噪聲,進而假設碼片判決的誤碼片基本為零,這一要求對軍用擴頻通信是不利的,而且也不符合擴頻通信利用擴頻增益降低誤碼的原則。
  2. A new method is put forward on thermodynamics combustion model to make imitating research on egr - a software is made to calculate the amount of no from the gasoline by connecting with the practical condition in our country, starting with thermodynamics and experiment at the same time make a system research to influence by the exhaust gas returning system on the gasoline, such as exhaust gas, fuel economy, and power, finally a new thought is afforded for optimizing all the egr parameter in chapter 6

    第五章採用上述診斷和預測模型對bj492q發動機進行了模擬計算和實驗研究,並探討了點火提前角、廢氣系數、燃空比、壓縮比和火花塞位置對發動機性能的影響。第六章提出了基於熱力學燃燒模型對egr進行數值模擬的方法,系統地研究了車用汽油機加裝egr系統后對排放、油耗、的影響,並結合排放標準。提出了egr參數的全局優化的新思路。
  3. ( 3 ) there are many flaws in direct laser metal sintering, such as the high remnants stress, micro - hole and micro - crack in sintering parts. in order to solving those problems, the programming of scanning paths is put forward, and several parts are prepared with different scanning paths respectively. the following conclusion is educed : the parts produced with short - side scanning path and same scanning direction have the minimum structure, the rigidity of parts prepared by short - side and same direction scanning path is highest, and the density of parts produced with the vertical scanning path is maximal

    ( 3 )針對採用大激光直接燒結鎳基高溫合金成形金屬零件存在的問題,如較大的應力,製件中存在著微裂紋、微孔洞等缺陷,初步提出掃描路徑的規劃,並採用幾種不同的掃描方式進行燒結試驗,發現採用短邊掃描路徑和同向掃描能夠獲得更加細小和分佈均勻的組織結構,採用短邊同向路徑制備的試樣其顯微硬度最高,而採用變向掃描(垂直)路徑制備的試樣緻密性最好。
  4. Combined with the adaptive modulation and coding technology, this algorithm reallocates the residual power by effectively utilizing the discrete modulation orders according to the different priorities of sub - channels under the limitation of quality of service over the block fading channel

    在滿足服務質量要求的前提下充分利用星座圖尺寸的離散性,將殘余功率按照各子通道的不同優先級進行二次分配,並結合自適應調制編碼技術改善低信噪比時的系統吞吐量。
  5. Proposes a novel algorithm of power allocation, called re - allocation of residual power ( rarp ), in the spatial multiplexing scheme of multiple input multiple output ( mimo ) system

    摘要研究空間復用多輸入多輸出系統的分配問題,提出一種新的分配演算法殘余功率再分配。
分享友人