殘余勢力 的英文怎麼說

中文拼音 [cányúshìlì]
殘余勢力 英文
remaining forces
  • 殘 : Ⅰ形容詞1 （不完整; 殘缺） incomplete; deficient 2 （剩餘的; 將盡的） remnant; remaining 3 （兇惡...
  • 余 : Ⅰ動詞（剩下） remain; leave: 9減4 余 5。 nine minus four is five ; four from nine leaves five ; i...
  • 勢 : 名詞1 （勢力） power; force; influence 2 （一切事物力量表現出來的趨向） momentum; tendency 3 （自...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 勢力 : force; power; influence
  1. In the majlis these consist of a rump of khatami - style reformists and a larger block of people who travel under the “ conservative ” banner but who are pragmatic in their approach and oppose mr ahmadinejad ' s brand of what many outsiders have come to call “ neoconservatism ”

    在伊朗議會中，這些聯盟組成部分主要有哈塔米派改革家的小部分殘余勢力，另外一大部分則是那些打著保守主義旗號但在行事中注重實效，這些人反對艾哈邁迪內賈德先生的做派?許多外國人都稱之為「新保守主義」 。
  2. After the gate has been secured, fenix and the new praetor artanis shall lead our surviving brethren to shakuras

    在那之後，菲尼克斯和新上任的裁決官阿爾坦尼斯會將我們的殘余勢力帶到沙庫拉斯。
  3. The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased

    本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。
  4. The basic physical and mechanical properties, mineral composition, micro structures, swelling potential, consolidated drained triaxial shear strength, parameters of constitutive model and residual strength of the soft clayey rocks were tested in laboratory with a large number of natural samples. the changing trend of the strength about these rocks is obtained by modeling the condition of softening due to immersion. from the principles of modern soil mechanics, the structural and swelling characteristics of soft clayey rocks were analyzed systematically

    本文通過現場調查，查明風化泥質軟巖的宏觀結構特徵，利用現代試驗測試手段，取原狀土系統進行特殊土室內土工試驗，測定土的基本物理力學特性、礦物成分及微觀結構、膨脹性、三軸排水剪強度及本構模型參數、軟化殘余強度，並模擬土體在長期浸水軟化后的強度變化趨勢，測試該類土的浸水軟化殘余強度。
  5. Residual stresses of bst thin films are tensile stresses, grain size and stresses increase with annealing temperature

    Bst薄膜殘余應力表現為張應力且隨著薄膜晶化溫度升高，薄膜的晶粒變大，殘余應力呈變大的趨勢。
  6. Finally, the technic route for the research of milling distortion is proposed. in chapter 4, the effect of tool path and clamping schemes on residual stresses as well as machining distortion are analyzed by using three - dimensional elastic - plastic fem ( finite element method ). the distortion variation tendency under four typical tool paths, the pressing - plate clamping and stretched fixation is obtained respectively

    第四章基於上述理論基礎，利用三維彈塑性有限元技術分析了走刀路徑和裝夾方案對銑削加工殘余應力分佈和變形的影響，得到了四種典型的走刀路徑以及壓板式裝夾和拉伸裝夾對加工變形的影響趨勢。
分享友人
分享到 Line

分享到臉書