比例控制器 的英文怎麼說

中文拼音 [bǐlìkòngzhìqì]
比例控制器 英文
proportional controller; controller
  • 比 : Ⅰ動詞1 （比較; 較量高下、 長短、距離、好壞等） compare; compete; contrast; match; emulate 2 （比...
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 比例 : 1. （長度上縮小和放大的倍數） scale; scaling 2. （比率） proportion; ratio; proportionality
  • 控制器 : controller; regulator; monitor; pilot; keyer; manipulator; control unit; control device; [自動化]...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. The main substance of the part is the designing of four types of fuzzy controller : fuzzy controller of pd type, fuzzy controller of pd type - proportion multiple controller, fuzzy model reference learning controller and double stage fuzzy controller, and made emulation study of their controlling fruitage

    這部分的主要內容是設計了pd型模糊控制器、 pd型模糊-比例復合控制器、模糊模型參考學習控制器和二級模糊控制器等四種模糊控制器，並對它們的控制效果進行了模擬研究。
  2. Lem two axis leveling control for proportional valves

    自動找平控制器lem700兩軸比例輸出自動找平控制器
  3. The electrical section contains the solid-state proportional temperature controllers and solenoid valves.

    電子控制室內有固體線路的比例溫度控制器和電磁閥。
  4. The results of experiments have show that electro - hydraulic proportional control system and its core controller of the auto crane ’ s performance are satisfied. it has the advantage of easily using and low cost, then it is worthy of further developing

    核心控制器樣機的試驗情況表明，本文所設計的汽車起重機電液比例控制系統具有簡潔實用、成本低廉的優點，證明了本文研發成果的有效性和實用價值，為產品的產業化開發打下了良好的基礎。
  5. Based on general fuzzy controller, the thesis gives how the controller ' s performance is influenced by factors of proportionality, membership function and defuzzification method

    以常規模糊控制器設計為基礎，探討了量化因子和比例因子、隸屬函數、非模糊化方法等對控制器控制性能的影響。
  6. The stability of electric power system has been being focused for a long time toprevent a power system from losing synchronism after sudden fault ， researchers have done much work and got many accomplishments this paper applied the direct feedback linearization ( dfl ) technique on the power system ， a strong nonlinear system simulation results by matlab proved this method efficiency main works and results are as follows ： this paper compared some existing methods in excitation control ， fast valve control and coordinated control respectively, analyzed the developments and actuality of nonlinear control research in brief, illustrated why ransient stability could be greatly improved by using the fast valve control in chapter 3 ， indicated the importance of coordinated control farther this paper introduced the inverse system theory, based on which ， discussed the dfl theory, pointed out which had consistency with the inverse theory, expanded the dfl theory combined the idiographic model equations ， made which adapt to the model of a single machine - infinite bus power system this paper referenced abundance articles and educed a set of equations ， which could describe the dynamical process of excitation and fast valve control for synchronous generators in the equations ， there were several very important parameters of power system - - rotor angle ( ) ， rotor speed ( ) ， generator q axis voltage ( eq ) ， transient voltage ( e ' q ) ， active power ( pe ) ， mechanical input power ( pm ) ， valve opening ( ) ， generator terminal voltage ( vt ) ， based on the model ， nonlinear coordinated controller and terminal voltage optimal controller have been designed by using the expanded dfl theory and lq optimal control theory the simulation results showed that the controller could keep power system transiently stable under the effects of a symmetrical 3 - phase short circuit fault ， which achieved better postfault regulation compared with another two routine methods ， one is the proportion excitation controller and proportion fast valve controller, the other is the proportion excitation controller and the optimal fast valve controller, which could exert good performance when met 1ittle disturbance either

    在介紹逆系統理論的基礎上，詳細介紹了dfl理論，通過比較闡明了dfl理論其本質是逆系統方法的一類，並結合具體課題推導出的模型方程將dfl理論進行了擴展，使之適應于電力系統這個強非線性對象。通過參考大量的書籍文獻推導出一套實用的可將大型汽輪發電機勵磁與汽門綜合起來進行控制的模型方程，此模型方程涵蓋了電力系統中特別引人注目的幾個量- -轉子角、轉子轉速、發電機q軸電勢eq 、暫態電勢e ' q 、有功功率pe 、機械功率pm 、汽門開度、機端電壓vt ，在此基礎上建立了實用的電力系統簡化的數學模型，並將擴展的dfl理論應用於此模型系統，結合線性二次型最優控制理論設計出大型汽輪發電機的非線性綜合控制器及機端電壓最優控制器，通過模擬實驗與採用常規的按電壓偏差進行調節的比例式勵磁控制器+汽門比例控制及採用常規的按電壓偏差進行調節的比例式勵磁調節器和基於二次型性能指標設計的最優快控汽門（考慮發電機的飽和因素）進行了對比，證實了採用此種控制器可以有效地提高電力系統的暫態穩定性，並且在電力系統遭受小干擾時同樣具有良好的調節性能。
  7. Remote control construction machinery will be more and more widely used along with development of technique and perfection of function of wireless control system and electro - hydraulic control system. the remote controlled trimming dozer is remotely controlled by signal that is transferred by electromagnetic wave and sent into driver - electro - hydraulic control system

    隨著無線電控制系統和電液控制系統的技術發展和功能完善，遙控型工程機械應用范圍將越來越廣泛，遙控型推耙機通過電磁波傳輸控制信號並將控制信號送入驅動執行器?電液比例控制系統以實現遠距離控制。
  8. Electric - pneumatic proportion control technology is the core of the pneumatic to control part of virtual instrument system. the hardware regards two high - performance data collecting card pcl - 818ls as the core. the software regards visual basic6. 0 as the developing platform, uses dynamic link library technology to realize the control on hardware of the virtual instrument, it realizes to be soft interrupt and dma data gather, make single channels data gather frequency up to 40 khz at most under windows system

    本套虛擬儀器系統的氣動控制部分以電?氣比例控制為核心，硬體以兩塊高性能數據採集卡pcl - 818l為核心，軟體以visualbasic6 . 0為開發平臺、使用動態連接庫技術來實現虛擬儀器對硬體的控制，並且實現了在windows系統下軟中斷和dma數據採集，使單通道最大數據採集頻率達到40khz 。
  9. Dcw proportional amplifier introduced in this paper is used in the double ways control system. it can control tow electromagnetic iron at the same time

    本論文所介紹的dc - w型雙向電液比例控制器是用於雙通道控制型比例閥中，可控制兩個比例電磁鐵。
  10. This system captures the rack position signal and rotate speed signal of the fuel injection pump, and calculates the circulating fuel injection quantity by programming the computer. then the computer is programmed to control the daq board to generate a certain width pulse. finally, controlled by the pulse, the alcohol injection system injects a certain quantity alcohol into inlet manifold according to a setting diesel / alcohol proportion

    該系統採用了在labview平臺上開發的pc總線?插卡式虛擬儀器系統，系統通過採集噴油泵的供油拉桿位置信號和轉速信號，利用計算機計算得出柴油的循環噴油量，再根據程序設定的柴油/酒精比例控制數據採集卡發出一定寬度的脈沖，控制低壓酒精噴射系統按比例將酒精噴入進氣歧管。
  11. Methods of evaluating the performance of time proportioning controllers for use in industrial - process control systems

    工業過程式控制制系統用時間比例控制器性能評定方法
  12. First, an ip position controller is designed according to the estimated plant model to match the time - domain command tracking specifications

    文中首先依據系統模型在時間領域下，符合命令追隨之規格來設計積分比例控制器。
  13. This paper analyses the type, function and characteristics of usual proportional control valves and raises a new modificative version in the light of their drawback. that is, basing on the principle of flow amplification and electrical feedback and throughout calculation and analysis on flow closed loop control and pressure flow combination., determination of the minimum controlled pressure difference as well as flow controlling range and structure of main valve and research of the dynamic and static characteristic, the paper puts forward control principle of " flow - load pressure change - displacement revision " and pressure / flow double closed loop, and further expounds that using a proportional controller and a electric mechanical transducer can separately serve the control function of pressure or flow as well as flow pressure combination

    本論文分析了目前常用比例閥的類型、功能、特性，並針對其不足提出新的改進方案，即：以流量放大，電反饋兩個原理為基礎，通過對流量閉環控制及壓力流量復合的計算分析、確定上最小控制壓差及流量控制范圍，確定主閥結構、功能特性研究等，提出了「流量? ?負載壓力變化? ?位移修正」的控制原理和壓力流量雙閉環控制原理，並進一步論述了利用一個比例控制器和一個「電?機械轉換器」就可完成獨立的壓力或流量控制功能以及流量壓力復合控制功能。
  14. This paper introduced the principle and realization method as well as control characterristics of the electrohydraulic servo proportional control system of the vrc robot. its nationality are also been discussed

    介紹了vrc機器人電液伺服/比例控制系統的原理、實現方法與控制特點，為該技術國產化進行了理論探討
  15. Expect for the design of the amplifier, the emphases is to test the static state and dynamic characteristic of the control system and provide a great deal reference data so that the system can work well

    論文中除了對放大器的電路做了介紹外，重點是對放大器在比例控制系統的運行中做了大量的靜態、動態參數測試，為比例電磁閥的良好工作提供了一系列的參考數據。
  16. One reason is that poor of technical level, most civil manufacturers ’ products are based on the imported electro - hydraulic proportional controller which is act as the core, as a result, the cost become higher and lost the advantage of lower cost

    在我國由於起步晚，技術水平低，汽車起重機生產廠商往往需要從國外引進電液比例控制系統核心控制器，以提升自身產品的競爭力。
  17. According actual situations, a system design pattern called “ double cpu share memory ” is adopted for such a kind of electro - hydraulic proportional controller. so in the third part, the concrete realization is presented to show the efficiency of the system design pattern, in the middle of which it emphatically give out the design of the hardware driving model

    針對怎樣實現汽車起重機電液比例控制系統核心控制器問題，即系統的設計問題，本文從整體上研究和比較了多種方案，最終選擇了雙處理器共享內存的體系結構模式，並且從硬體和軟體上完成了核心控制器的詳細設計。
  18. Gas air ratio controls for gas burners and gas burning appliances - part 1 : pneumatic types ; amendment a1 ; german version en 12067 - 1 : 1998 a1 : 2003

    燃氣燃燒器和燃氣裝置用燃氣空氣比例控制器.第1部分
  19. The connections and characteristics of electric current, force and displacement of the proportion electromagnetism had been studied and tested. in the meantime, the proportion controller of the electromagnetism had been improved

    再對比例電磁鐵的電流、力和位移三者之間關系和特點進行了試驗研究，同時對其控制器電子比例控制器進行了改進。
  20. The objective of this dissertation is a kind of press - high speed numeric control oil - press. with a theoretical analysis and study about proportional control system, this paper sets up the mathematical model of proportional valve controlled non - symmetry hydraulic cylinder via the hydraulic system model building. then analyzes and modifies the model based on the matter of this study, and simulates the model with matlab software to confirm pid parameters, thus designs the pid controller

    本學位論文針對一具體的研究項目?高速數控壓機的開發，對比例控制系統進行理論分析與研究，通過對液壓系統的精確建模，建立起比例閥控非對稱液壓缸的數學模型，然後根據所研究問題的實際情況對模型進行必要的分析和修正，再運用模擬軟體matlab分析系統模型及確定pid控制參數，設計出pid控制器，使得控制系統的設計具有更多的可靠性和靈活性，最後運用pic單片機實現此控制，並結合整機調試試驗驗證了pid控制的成功。
分享友人
分享到 Line

分享到臉書