比例控製程序 的英文怎麼說

中文拼音 [kòngzhìchéng]
比例控製程序 英文
ratio controller
  • : Ⅰ動詞1 (比較; 較量高下、 長短、距離、好壞等) compare; compete; contrast; match; emulate 2 (比...
  • : 動詞1 (告發;控告) accuse; charge 2 (控制) control; dominate 3 (使容器口兒朝下 讓裏面的液體慢...
  • : 名詞1 (規章; 法式) rule; regulation 2 (進度; 程序) order; procedure 3 (路途; 一段路) journe...
  • 比例 : 1. (長度上縮小和放大的倍數) scale; scaling 2. (比率) proportion; ratio; proportionality
  • 程序 : 1 (進行次序) order; procedure; course; sequence; schedule; ground rule; routing process 2 [自動...
  1. Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc

    本文根據大量的國內外文獻,對研配液壓機的工作原理及設計結構進行了簡介;對位置同步的制方法進行了較分析,提出閥和伺服閥復合制的閉環結構來對非對稱雙缸進行同步制電液同步制方案;在此基礎上著重對非對稱缸建模,最後得到位置制系統的總體數學模型,從理論上對同步系統動態特性進行了分析,並用pid制器進行參數整定,減小雙缸同步誤差、提高系統的動態響應性能;其中制性能的分析藉助于matlab軟體中的simulink工具箱,由已建立的數學模型形成模擬模型,得到可視化的模擬結果,從而利於交互方式下調整參數,了解不同的參數對系統的影響,優化同步系統的動態性能;在深入了解系統的動作特性后,對plc制研配液壓機的原理進行了探討,針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃,編制出研配液壓機動作,在編中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid制在plc上的實現及bcd碼撥盤輸入的植入問題。
  2. The design of high - voltage circuit based on pwm technology is briefly described. the closed - loop current control theory using analog instruments is fully discussed, followed which is that using digital instruments. it is an important part that the hardware and software design of the single chip - two arms and two chips - two arms current control circuits with a new chip applicable to digital current control system

    簡單介紹了基於開關電源技術的高壓電路設計;詳細講述了模擬穩流電源的閉環穩流原理,並在此基礎上討論了利用數字電路實現穩流的原理及可能性;選擇出適合數字穩流系統的新型晶元,完成了單片雙路穩流系統、雙片雙路穩流系統的軟硬體設計;給出了一種簡單易實現的?積分
分享友人