氣體壓力焊接 的英文怎麼說

中文拼音 [qìtǐyālìhànjiē]
氣體壓力焊接 英文
gas pressure welding
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 體 : 體構詞成分。
  • 壓 : 壓構詞成分。
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 氣體 : gas; gaseous fluid
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  1. Standard qualification procedure for gas pressure welding technique

    氣體壓力焊接技術合格鑒定標準程序
  2. The paper mainly discussed the reasons of stress from liquid ammonia pressure vessel causing crack through examing data and experimental results and analysing relevant referential documents and materials, taking 1200 ammonia vessel ' s crack and leaking in a certain fertilization company as an example : there existed remaining welding, stress in the equipment ; there existed a stress decaying surrounding, i. e., moisture 0. 2 %, and temperature > - 5 with o2 or co2 inside ; the higher the intensity of raw materials, more possible it was to have stress decaying crack

    摘要以某化肥公司1200氨冷器殼體開裂泄漏的失效分析為例，通過對檢驗數據和結果及有關文獻資料的分析研究，探究了液氨介質壓力容器產生應力腐蝕裂紋的原因：設備中存在較高的焊接殘余應力；液氨介質具備應力腐蝕環境，即含水量0 . 2 % ，且有空氣（ o2或co2 ）污染（或摻入） ，使用溫度高於零下5 ；母材強度越高，應力腐蝕裂紋產生的傾向就越大。
  3. By using diffusion welding method ( under certain welding parameters such as temperature, pressure, time and atmosphere, etc ) and employing rational structural control technique, a kind of 93w - ofc - tc4 - a1 - mb2 system flier - plate with good parallelism, planeness and high densification was prepared, which met the needs of initial design and the basic requirement of flier - plates

    利用平面擴散焊接法（控制一定的溫度、壓力、時間、氣氛等條件） ，同時採取合理的結構控制方法，成功實現了93w - ofc - tc _ 4 - al - mb _ 2的整體連接，得到了平面性好、平行精度高、整體緻密的波阻抗梯度飛片，滿足了設計結果和梯度飛片的基本結構要求。
  4. Acceptance tests for co2 - laser beam machines for welding and cutting - part 3 : calibration of instruments for measurement of gas flow and pressure

    Co2激光束焊接機和切割機的驗收試驗.第3部分:氣體流量和壓力測量儀的校準
  5. Acceptance tests for co2 - laser beam machines for high quality welding and cutting - calibration of instruments for measurement of gas flow and pressure

    高質量焊接和切割用co2激光束機的驗收試驗.氣體流量和壓力測量儀的校正
  6. To meet the growing demand of china and asia market, chart invested 4 entities in china successively since 1995. adopting the advanced equipment, technologies and management from charts headquarter, chart china is able to provide china and asia market with various cryogenic equipment, such as liquid cylinders, bulk tanks, trailers, vacuum insulated pipe systems, according to the international codes as well as chinese code and regulations, and better service and technical support for customers of these regions

    為了適應中國及亞洲地區經濟高速發展的市場需求，查特mve從1996年起先後在中國投資建設了4家公司，應用美國查特公司總部的先進設備技術和管理，按照國際相關標準及中國壓力容器現行規范和標準進行深冷設備的生產製造，為國內及亞洲地區的客戶提供世界一流品質的焊接絕熱氣瓶真空絕熱管道大型深冷貯罐低溫液體槽車等各種深冷設備，同時為客戶提供更及時周到的服務與支持。
  7. Transportable gas cylinders - specification for welded pressure drums up to 1000 litre capacity for the transport of gases - design and construction ; german version en 14208 : 2004

    可運輸氣瓶.氣體運輸用容量在1000升及以下的焊接壓力
  8. Answer : ( 1 ) prevent to splatter the metal is caused burnable with fire ; ( 2 ) avoid the harm of electric arc ray radiation to human body ; ( 3 ) prevent certain and harmful gas toxic ; ( 4 ) soldering when pressure vessel, should prevent to solder produce explosion ; ( 5 ) when headroom works, want to take safety belt and safety helmet ; ( 6 ) the attention prevents accident getting an electric shock

    答： （ 1 ）防止飛濺金屬造成灼傷和火災； （ 2 ）防止電弧光輻射對人體的危害； （ 3 ）防止某些有害氣體中毒； （ 4 ）在焊接壓力容器時，要防止焊接發生爆炸； （ 5 ）高空作業時，要帶安全帶和安全帽； （ 6 ）注重避免觸電事故。
  9. Transportable gas cylinders - specification for welded pressure drums up to 1000 litre capacity for the transport of gases - design and construction

    可移動式儲氣瓶.氣體運輸用容量最高達1000升的焊接的壓力桶規范.設計和建造
分享友人
分享到 Line

分享到臉書