水平土壓力 的英文怎麼說

中文拼音 [shuǐpíng]
水平土壓力 英文
horizontal earth pressure
  • : 名詞1 (由兩個氫原子和一個氧原子結合而成的液體) water 2 (河流) river 3 (指江、河、湖、海、洋...
  • : Ⅰ形容詞1 (沒有高低凹凸 不頃斜) flat; level; even; smooth 2 (高度相同; 不相上下) on the same l...
  • : 壓構詞成分。
  • : Ⅰ名1 (力量; 能力) power; strength; ability; capacity 2 [物理學] (改變物體運動狀態的作用) forc...
  • 水平 : 1. (跟水面平行的) horizontal;level2. (達到的高度) standard; level
  1. After analyzing the soil stress, flexure moment data of central section of the sheet, and the flections data of two kinds of holding sheet models which are different on span, the paper gets the horizontal and vertical soil stress distribution rules and compares the result of the exam with calculating result of classic soil stress theory

    通過對兩種跨度的擋板模型的、擋板跨中彎矩、擋板跨中撓度值的分析總結,得到了擋板後沿高度及方向的分佈規律,並在分佈形式及數值大小與經典理論作了比較。
  2. Abstract : this paper analyzes causal factors of flood in the middle reaches of changjiang river. due to neglection of environmental management, soil erosion in the upper and middle reaches of the changjiag river, lake sedimentation, large - scale reclamation of marshes, the flood regulation capacity of the lake was descended, and flood stage was risen and prolonged. consequently more and more river levees and lake dikes were reinforced almost every year to prevent the disasters, which made flood level go up and flood period last for more days. the frequency of flood and waterlogging disasters rose and their damage was enlarged. several proposals for flood prevention including agricultural modernization are put forward

    文摘: 1998年長江大洪后開始實施的「垸行洪,退田還湖」的地利用調整方案,從長遠來說應尋求農業安全且收入逐漸提高條件下的地利用,長江中游地區應積極推進農業現代化,提高農業勞動生產率,轉移,減少分蓄洪區的人口,移民建鎮,對區內的地要促進其規模經營,由優秀的有文化的農民經營,時只有少量的直接從事農業生產的經營管理人員,農忙時則大量地使用季節性合同工或實現機械化,大洪時退田還湖,減輕長江幹流大洪,減少分洪與特大洪災時的損失,這樣還可促進避洪、冬季農業等的發展,也有利於長江中上游地區陡坡耕地的退耕還林,還可在糧食充足時進行休耕,在旱災、糧食緊張時擴大糧食生產?
  3. Now some universities and institutes of china have made some samples of the lunar rovers and theirs wheels, but until now the wheel ’ s mechanical performance is seldom researched and tested. this paper will analyze the mechanical performance of the wheel and design a test - bed to test the performance of the lunar rover ’ s wheel. firstly, the mechanical characters of the soil are separated to press - sinkage character and shear character based on bekker ’ s theory, and common press - sinkage and shear models are introduced and the theory of lankine passive earth pressure is also introduced

    根據bekker半經驗法的基本思想,將壤的學特性分解為方向的剪切特性和豎直方向的承特性,闡述了地面學中常見的壤的承、剪切等學模型,並引入了朗肯被動理論,為建立車輪在松軟壤中前進和轉向的學模型奠定了基礎,同時進行了實驗壤的剪切實驗,測量了壤的內聚和內摩擦角等參數。
  4. Finally, we suggest we should observe the horizontal and vertical deformation and water press in soil in construction, in order to avoid the huge accident and ensure the quality of construction. through the practice of binhai road in shenzhen, the studies result was further confirmed

    最後本文提出,在濱海軟路基施工中,對軟地基的、豎向變形以及中孔隙必須進行監控以保證軟路基施工的質量和預防重大事故的發生,並強調以現場原位試驗來確定軟工程學性質,將更符合工程實際。
  5. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造,設計了四種類型矩形鋼管混凝柱與鋼梁連接節點,包括常規栓焊( wfp )節點、翼緣全螺栓連接( bfp )節點、雙t板連接( dst )節點以及加勁端板連接( sep )節點,進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究,比較了不同軸比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵,主要結論有: 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈,沒有或略有捏攏現象,耗能能強; 2 、軸比對節點滯回曲線有顯著影響,全部節點都有顯著的剛度退化; 3 、位移與轉角骨架曲線在峰值荷載後有較長的或下降段,具有良好的延性性能; 4 、從整體抗震性能上看,翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點,可在實際工程中加以推廣。
  6. In this test, a special bolt - jack is used to exent of prestressing force to brace angles as the whole structure is under dead - load. in this state brace angles withstand partly load before twice - load and the stress and strain of concrete are decreased. in this way the aim of removal of load and strengthening can be reached

    本試驗中採用專用螺栓千斤頂在恆定荷載下對混凝柱角鋼撐桿施加預,使外包角鋼在二次受前即分擔部分荷載,使混凝和應變降低,達到卸載與加固同步進行的目的。
  7. This paper sets up a fuzzy optimum math - model of the prestressed degree for prestressing bundle disposition of prestressed concrete continuous beam bridges, which is transformed into a clear math program by - level cut - set. by the solution of the clear math program, a succession of reasonable prestressing moments can be obtained. then it is convenient to dispose the prestressing system by only taking account of geometric factors of all controlling sections. based on this, a theory of automatic disposition of the prestressing bundles is proposed and an engineering example is given to demonstrate it

    建立預應混凝連續梁橋預應度的模糊優化問題,按-截集解法,將模糊優化問題轉化為確定性的數學規劃問題.求得一較合理的消彎矩后,只需按控制截面的構造進行預應體系設計.在此基礎上提出了配束自動化的基本思想,並以一實例說明其理論應用
  8. Abstract : this paper sets up a fuzzy optimum math - model of the prestressed degree for prestressing bundle disposition of prestressed concrete continuous beam bridges, which is transformed into a clear math program by - level cut - set. by the solution of the clear math program, a succession of reasonable prestressing moments can be obtained. then it is convenient to dispose the prestressing system by only taking account of geometric factors of all controlling sections. based on this, a theory of automatic disposition of the prestressing bundles is proposed and an engineering example is given to demonstrate it

    文摘:建立預應混凝連續梁橋預應度的模糊優化問題,按-截集解法,將模糊優化問題轉化為確定性的數學規劃問題.求得一較合理的消彎矩后,只需按控制截面的構造進行預應體系設計.在此基礎上提出了配束自動化的基本思想,並以一實例說明其理論應用
  9. Firstly, for the system of moulding board and support frame in construction the side pressure and screws are analyzed. the material and structure form of support frame are discussed. the design of support frame uses the method of limited state, and also it analyses the integer stability, part stability, and single stability, and then proposes the load analysis of multi - level support frame

    首先,針對轉換層梁模體系及支撐架施工,重點分析了轉換層結構現澆混凝對模板側值及模板對拉螺桿的計算;討論了轉換層支撐體系的形式及構造,詳細論述了基於極限狀態設計的支撐架計算方法,包括縱橫向桿的強度驗算、立桿的整體穩定性、局部穩定性、單肢桿件穩定性等驗算,並提出了多層支撐架的施工荷載計算方法。
  10. Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating

    箱梁製造由鋼筋工程、模板工程、混凝工程、預應工程、移存梁工程、孔道漿工程、梁體封端工程、橋面防層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋,分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模;拆裝式和液式兩種模板的設計、製作要求和使用方法;綜合考慮、優化混凝配合比,混凝灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板分層、附著式振搗為主、插入式搗固為輔的施工工藝,蒸汽養護的方法和規定;應應變雙控制確保預應施工質量的施工技術;採用重物移運器有效移梁的施工方法;漿、封端、橋面防層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法,並可為以後類似施工作借鑒。
  11. On current projections, substantial parts of the world risk being left uninhabitable by rising sea levels, reduced freshwater availability or declining agricultural capacity. this will exacerbate existing migratory pressures from rural areas to cities, from unproductive land to more fertile land, and across international borders

    從目前的狀況來看,海面的上升、淡資源的減少以及農業生產能的下降,將使世界上絕大多數地區淪為不適宜人類居住的不毛之地,這將進一步加劇從鄉村到城鎮、從地貧瘠地區到豐腴地區乃至跨國界的移民潮所帶來的
  12. According to the new concrete code, the calculation formula are put forward concerning the load - carrying capacity during construction, the load - carrying capacity of cross - section bending, longitudinal shearing, the inclined - section shearing and part shearing during the application of the continuous composite floor slab, which provide the design proofs for the continuous composite floor slab

    摘要根據新混凝規范,給出了連續跨型鋼板與混凝組合板施工階段的承載計算公式及使用階段的正截面抗彎承載、縱向抗剪承載、斜截面抗剪承載和局部抗沖切承載計算公式,為連續組合樓板的設計提供了依據。
  13. Pressure grouting has made piles and soil combinaion closely at the same tiine, the piles liave hand load capacity more than ever currenly, the design and calculation of root piles have been short of a sult of fledged theory aner referencing the application of root piles in underpinning engineering and basing on the intrinsic cbaraer of root piles in thes paper the authr has ehabshed mle constitutive relative of root piles and soil in correctin slopes, researched the slope edility aller correcang slopes and safety factr of slopes

    樹根樁可以看作是一種摩擦樁,它不僅可以承擔豎向荷載,而且還可以承擔荷載,用注漿可以使樁與體緊密結合,使樁具有較大的承載。當前,對樹根樁的設計計算卻沒有一套成熟的理論,本文在參考了樹根樁應用於托換工程的設計計算方法后,根據樹根樁的實際特徵,詳細推導了樹根樁加固邊坡后樹根樁與均質化復合「體」的本構關系,研究了樹根樁應用於邊坡加固后的穩定性情況。
  14. Then it follows that under stable seepage the water pressure outside the foundation pit is reduced with a little change of the total horizontal pressure, while the water pressure inside the foundation pit is increased with a great change of the total horizontal pressure

    針對這一情況,利用流網分析了在基坑周圍存在穩定滲流時支護結構上的變化,並對其變化進行了分析與對比計算,得出繞支護結構的穩定滲流減小了主動側的,但總的變化不大;被動側的有所增加,但總的減小較多。
  15. The in - situ testing includes surface deformations, sub - surface movements, earth pressures, pore water pressures, underground water levels, spt, stresses of pipes and pipe - soil contact stresses. in addition, the total jacking forces, deviations in line and level of the pipe line and earth pressures in the earth pressure balance machines ( epbm ) are also recorded. the results of field - testing are analyzed, and the variety of testing datum include earth pressures, pore water pressures and underground water levels during the course of the shield through it are studied

    現場測試內容包括地面變形、深層體變形、變化、孔隙變化、地下位變化、體標準貫入試驗、管道內變化、管接觸應變化以及頂管施工現場記錄(包括頂面偏差、高程偏差等) 。
  16. Through the analysis and calculation the conclusion can be made that during the process of the timbering of excavation, the magnitude of soil stress decreases with the increase of the displacement on the base of the still earth pressure, and the earth pressure distribution varies from the triangular distribution of the still earth pressure to other distribution with the displacement of the timbering structure. the thesis introduces the bedding coefficient in the horizontal direction varying with the soil displacement from soil - structure interaction mode, therefore calculation can be made to get more rational calculation result using elastic foundation finite element method which is the same to timbering structure both upwards and under excavation surface

    通過分析計算可以得出,在基坑支護過程中,的大小在靜止值的基礎上隨支護結構向坑內側位移增大而減小;的分佈由靜止的三角形分佈隨支護結構位移變化成其它分佈;由-結構共同作用模式引入隨體位移變化的向基床系數,使支護結構在開挖面以上部分同以下部分一樣,均可採用彈性地基有限元法進行計算,得出更為合理的計算結果。
  17. The flexible retaining structure is another important retaining structure in soft soil. the integrated numerical analysis of this retaining structure ( including the methods and theory of calculating active earth pressure under sorts of conditions as well as the calculating method of horizontal stiffness coefficient of bracing structure and the method of deciding boundary condition etc. ) was gived. the effect of all parameters on the characteristics of retaining structure was discussed using methods of sensitivity - analysis

    本文針對目前常用的彈性支點法,給出了完整的數值分析方法,包括各種條件下的墻後的計算方法和原理、支撐系統(或錨拉系統)剛度系數的計算、邊界條件的確定方法等,並以此為基礎採用靈敏度系數分析方法討論了各參數對圍護結構形態的影響,指出體側向基床比例系數是影響圍護結構變形的最主要的參數。
  18. According to calculating and analysis, educes the distributing laws and their correlations of horizontal displacement and stress of stabilizing pile, anchor pull and earth press in two sides of pile, including the distributing of point repel force and internal force of pile at the terminal state, providing full theoretical basis for anchor cable and stabilizing pile structure design, strength check, stability check and determination of anti - slide force for a single stabilizing pile

    通過計算分析,得出了抗滑樁的位移、樁身應、錨索拉和樁側的分佈規律和它們之間的相互關系以及極限狀態時的樁的結點抗和樁的內分佈規律,為錨索樁的結構設計、強度校核、穩定性校核和單樁抗滑的確定提供了充分的理論依據,同時也提出了錨索抗滑樁計算分析的一種新方法。
  19. Besides, the dissertation introduces the general formula to calculation horizontal earth pressure on projecting conduit and trenching conduit

    同時還簡要介紹了上埋式管道和溝埋式管道水平土壓力的一般計算公式。
  20. Based on the routine test of rockfill, built indoor model experiment of it under the process of vibration compaction, the flat panel vibration machine was used to vibrate and compact the layered rockfill, the level instrument was used to observe the settlement of rockfill after vibration compaction, dynamical soil manometer was used to observe the pressure variety in the rockfill layer

    摘要在進行填石料常規工試驗的基礎上,建立填石料振動實的室內試驗模型,採用板振動器對填石料分層進行振動實,利用準儀觀測填石料在振動實中的沉降量,利用動計觀測填石層內的變化。
分享友人