水淬火 的英文怎麼說
中文拼音 [shuǐcuìhuǒ]
水淬火
英文
water quenching-
In this paper, 6013al / sicp / gr metal matrix composite ( mmc ) was produced by spray codeposition, by means of changing the medium of quenching, influence of five types of heat treatment system ( furnace cooling, air cooling, water quenching, dry ice quenching, liquid nitrogen quenching ) and different aging temperature on the damping was studied systematically
本文採用噴射共沉積方法制備了6013al sicp gr金屬基復合材料( mmc ) ,通過改變淬火介質,較為系統地研究了五種熱處理制度(爐冷、空冷、水冷、乾冰冷及液氮冷)以及不同時效溫度( 120 、 150 、 170 、 190及210 )對6013al sicp grmmc阻尼性能影響。He had seen them shape the knives from white-hot metal, temper them in cold water, then hone them to glistening sharpness.
他見到過他們把白熱的金屬做成刀,在冷水裡淬火,然後再把它們磨得鋒利鋥亮。Over 310, liquid nitrogen quenching and water quenching show higher damping capacities
當溫度大於310 , - 195淬火與水淬試樣表現出較高的阻尼性能。Testing of ceramic materials ; determination of resistance to thermal shock ; water quenching method for refractory bricks
陶瓷材料的試驗.測定耐熱沖擊抗性.耐火磚水淬法Analysis of quenching cracks of pump axle
水泵泵軸淬火裂紋分析Over a 100 to 270 temperature range, the damping capacities are ranked from great to small as follows : sample cooled in furnace, sample cooled in the air, sample quenched at - 70 ( sample quenched at - 195 ) and sample quenched in water
在100 270范圍內,不同熱處理態材料阻尼能力的大小以次為:其爐冷空冷70淬火- 195淬火水淬。超過270 ,由於阻尼性能測試出現第二個內耗峰,不同熱處理態試樣阻尼性能的大小沒有明顯的規律性。Standard test method for determination of thermal shock resistance for advanced ceramics by water quenching
用水淬火法測定高級陶瓷製品耐熱沖擊性的標準試驗方法Advanced technical ceramics - monolithic ceramics - thermomechanical properties - determination of resistance to thermal shock by water quenching
高級工業陶瓷.單片陶瓷.熱機械性能.水淬火法測定耐熱沖擊Advanced technical ceramics - methods of testing monolithic ceramics - thermomechanical properties - part 3 : determination of resistance to thermal shock by water quenching
高級工業陶瓷.單片陶瓷的試驗方法.熱機械性能.第3部分:水淬火法測定耐熱沖擊性Pit remediation & slop oil, industrial water, cutting & cooling oils, hexavalent chromium, acid & alkali with heavy metal content, steel mill & electro filter dust, spent catalysts, tempering salts, solvents recovery and recycling, sludge treatment and minimization, fuel - blending, thermal desorption and transfer centres
廢漿池和廢油、工業污水、巖屑和冷卻油、六價鉻、含重金屬成分的酸堿、鋼廠和電過濾器粉塵、反應過后的催化劑、淬火鹽、溶劑還原和回收、油泥處理和最小化、燃料混合、熱吸附和轉運中心。The lath width of martensite can be fined noticeably by pre - strained quenching at non - dynamic recrystallization to approach nanometer magnitude ( the average width is 120nm )
採用非動態再結晶溫度下的預應變-淬火,提高馬氏體相變形核率,可以超細化馬氏體的板條晶片寬度,使之接近納米量級水平(平均寬度達到120nm ) 。By plunging the hot metal into water, oil, or brine ( quenching ), the desirable characteristics are retained
將灼熱金屬插入水中或鹽水(淬火) ,還會保持理想的特性。Test method for determination of cooling characteristics of aqueous polymer quenchants by cooling curve analysis with agitation tensi method
通過攪拌冷卻曲線分析測定含水聚合淬火劑冷卻特性的方法Guide for evaluation of aqueous polymer quenchants
含水聚合淬火劑的評估指南Standard guide for evaluation of aqueous polymer quenchants
評價含水聚酯淬火劑的標準指南Test method of characteristics on polymer quenchants
有機物水溶性淬火介質性能測定方法分享友人