水霧噴嘴 的英文怎麼說

中文拼音 [shuǐwùpēnzuǐ]
水霧噴嘴 英文
hydraulic spray nozzle
  • 水 : 名詞1 （由兩個氫原子和一個氧原子結合而成的液體） water 2 （河流） river 3 （指江、河、湖、海、洋...
  • 霧 : 名詞1. （水蒸氣凝結成的小水點） fog 2. （像霧的許多小水點） fine spray
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  • 水霧 : spray
  1. As to the work about theory analysis, at first, the paper describes the atomizing and humidifying process of the centrifugal nozzle with firing pin type, high pressure and little aperture and liquid physical properties. later, combining with the structure characters of this kind of nozzle, the paper studies on the theory of the atomizing and humidifying process by three phases, which is water film forming phase, water film falling into pieces phase, and heat and mass transfer between water and air phase in turn

    理論工作方面，首先描述了撞針型高壓小孔徑離心式噴嘴的霧化加濕過程和液體的物理性質，然後結合撞針型高壓小孔徑離心式噴嘴的結構特點，將其霧化加濕過程分三個階段進行機理上的研究，這三個階段依次為液膜形成、液膜初次破碎及二次霧化、水與空氣的熱濕交換。
  2. Based on the theory analysis and experiment work, the paper studies the humidifying property of the centrifugal nozzle with firing pin type, high pressure and little aperture. compared with the traditional air washer, the high efficiency and energy saving character of this kind of nozzle is stood out

    課題從理論和試驗兩方面分析研究了撞針型高壓小孔徑離心式噴嘴的霧化加濕性能，並將其與傳統噴水室加濕系統進行能耗比較，突出了撞針型高壓小孔徑離心式噴嘴高效節能的特點。
  3. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  4. Integrated the work on theory and experiment, the paper provides technical performance material at large about the automating and humidifying character of the centrifugal nozzle with firing pin type, high pressure and little aperture to the manufacture and user. with the valuable reference during the selecting the equipment and ascertaining the parameters, the users could select and control the humid parameter

    課題的理論與試驗兩方面工作相結合，為撞針型高壓小孔徑離心式噴嘴的霧化加濕性能提供了較為詳細的技術性能資料，為生產廠家和用戶在設備選型和參數選擇過程中，提供了有價值的參考，便於用戶正確而經濟地選擇、控制濕度參數，有效調節噴嘴孔徑、噴水初溫和噴水壓力的大小。
  5. For some minutes it puffed away without speaking, but at last it unfolded its arms, took the hookah out of its mouth again, and said, so you think you re changed, do you

    有好幾分鐘，他只是噴著煙霧不說話。最後它松開胳膊，把水煙管從嘴裏拿出來，說： 「你認為你已經變了，是嗎？ 」
  6. The spray nozzles are designed to produce a dense spray at a predetermined angle.

    噴嘴是按預定角度產生稠密水霧來設計的。
  7. With gelatin liquor as adhesive and wheat meal as granulation material, the effects on spray granule ' s strength of fluidizing gas velocity, bed temperature, nozzle air pressure and adhesive concentration were studied experimentally in a batch conical fluidized bed spray particle generator

    本文在一間歇錐形流化床噴霧造粒器中，以食用小麥澱粉為原料，以明膠的水溶液為粘結劑，實驗研究了流化氣速、床層溫度、噴嘴霧化空氣壓力、粘結劑濃度對噴霧造粒顆粒強度的影響。
  8. Based on the induction phenomenon caused in gas hydrate formation, the influential rules of its gas entrance mode, temperature, pressure, water resources and nozzle on the induction time are analyzed by means of experimental study on the induction time of gas hydrate formation obtained by water spray and enhancement

    摘要以氣體水合物形成過程中的誘導現象為基礎，通過對噴霧強化方式制取天然氣水合物的誘導時間進行試驗研究，考察分析了系統進氣方式、溫度、壓力、水源及噴嘴等因素對誘導時間的影響規律。
  9. Quantitatively analyses the concrete influences on atomizing humidifying performance of the nozzle aperture, initial temperature and the pressure of spray water and the water - air ratio through a single factor experiment

    通過單因素試驗定量分析了噴嘴孔徑、噴水初溫、噴水壓力以及水氣比對霧化加濕的具體影響。
  10. Agricultural irrigation equipment - centre - pivot and moving lateral irrigation machines with sprayer or sprinkler nozzles - determination of uniformity of water distribution

    農業灌溉設備.有噴嘴或噴霧咀的橫向移動排灌機械和中心軸.水分配均勻性的測定
  11. Its atomized parcel is so small that no drip is separated out. this kind of centrifugal nozzle has high humidifying efficiency and low energy cost, which could be used in many situations in textile factories such as directly humidifying in workshop and humidifying in air pipeline

    撞針型高壓小孔徑離心式噴嘴的霧化粒子細小、無水滴析出、加濕效率高、耗能少，可直接向車間加濕，適用於紡織廠等多種應用場合。
  12. As to the work about experiment study, at first, the paper makes certain the prominent affecting factors to the automating and humidifying property of this kind of nozzle by orthogonal experiment. by jicha analysis method and fangcha analysis method, the paper got that the nozzle aperture, the initial water temperature and the spraying pressure have prominent effect to the humidifying property while the effect of the original air state is small

    試驗工作方面，首先通過正交試驗確定對撞針型高壓小孔徑離心式噴嘴霧化加濕性能影響顯著的因素，運用極差分析法和方差分析法，得到噴嘴孔徑、噴水初溫和噴水壓力對噴嘴的加濕性能影響顯著，而待加濕空氣初狀態的影響相對較小。
  13. Senninger irrigation is a manufacturer of high - quality irrigation components including sprinklers, spray nozzles and pressure regulators

    描述:色聶灌溉公司是一家高質量灌溉設備的製造商，其產品包括：灑水裝置，噴霧嘴，壓力調節器等。
  14. Water mist nozzle

    細水霧噴嘴
  15. The dehydration time is square of the droplets diameter so the small diameters of the droplets can cut down the drying time then reduce the height of the drying chamber. to the combined spin - flow pressure spray drying, the diameters of droplets are small and the dehydration rate is higher so keeping the qualities of the dried products we can increase the speed of the inlet wind and reduce the temperature of the outlet wind thus can improve the evaporation intensity of the drying chamber and the average energy utilization of the drying equipment

    因霧滴的脫水時間與其直徑的平方成正比，減小液滴直徑有利於縮短乾燥脫水時間，可有效降低乾燥塔的高度；由於旋流式組合壓力噴嘴霧化滴徑的減小，脫水速度明顯加快，在不影響乾燥物料性質的前提下，適當提高進風溫度，同時有效地降低排氣溫度，有利於提高幹燥塔的蒸發強度，也有利於提高幹燥設備的平均能源利用率。
  16. Experiment shows that when the gas hydrate is obtained by spray, its induction time is generally shorter, its phenomenon is not obvious, setting of initial temperature and pressure with an autoclave has certain influence on induction time, but not obvious, water resources and spray nozzle have bigger influence on the induction time

    試驗表明，噴霧方式制取天然氣水合物時，誘導時間普遍較短，誘導現象不明顯；反應釜設定初始溫度和壓力對誘導時間有一定影響，但不是很明顯；水源和霧化噴嘴對誘導時間的影響較大。
  17. Water injection system includes pulverization system and controlling system of water quantity. pulverization system includes air resource, water resource and gas - mist nozzle ; controlling system of water quantity includes booster, controlling circuits. water quantity is decided by hydraulic pressure and gas pressure

    噴水系統包括霧化系統及水量控制系統，其中霧化系統包括空氣源（空氣壓縮機） 、水源（加壓水）及氣?霧噴嘴；水量控制系統包括比例調壓閥、控制電路部分。
  18. Standard for safety for water mist nozzles for fire - protection service

    消防設備用水霧噴嘴的安全標準
  19. Test procedure for determining the uniformity of water distribution of center pivot, corner pivot, and moving lateral irrigation machines equipped with spray or sprinkler nozzles

    裝有噴霧器和噴嘴的中心旋轉軸彎頭旋轉軸和橫向移動的灌溉機噴水均勻性測定試驗程序
分享友人
分享到 Line

分享到臉書