汽化曲線 的英文怎麼說

中文拼音 [qìhuàqūxiàn]
汽化曲線 英文
vaporization curve
  • 汽 : 名詞1. （由液體或某些固體變成的氣體） vapour2. （水蒸氣） steam
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 汽化 : [物理學] vaporization; evaporation; carburate; boil off; nebulization汽化計 atmidometer; evaporat...
  • 曲線 : [數學] curve; bight; bought; profile; net曲線板 french curve; irregular curve; curve board; splin...
  1. Using the thermodynamic conditions describing the coexistence of two phases and the stability conditions of equilibrium state, we have calculated the normalized temperature and the normalized pressure of the triple point ( t1, p1 ), the melting curve, vapouring curve and the sublimation curve. the whole phase diagram of the 2d monatomic l - j system is obtained

    和杜宜瑾等人的方法類似，我們先給出了系統在相變點時的一些參數的數值，在此基礎上，考慮占據率q的因素，利用相平衡的熱力學條件及平衡態的穩定性條件，得到了二維單元l - j系統的熔化曲線、汽化曲線、升華曲線以及三相點的位置，從而給出了該系統的完整的三相圖。
  2. Some testing devices are of advanced ones, such as scanning electronic microscope, microfocus circular radioscope, water - immersed ultrasonic flaw detector, 3 - axis measuring machines, large - sized projector, etc. for the production of non - aero products, there are large - sized die - casting equipment, and nearly 100 pieces of specialized gear machine tools including worm - gear grinding machine, etc. it has some specialized production lines for piston, crankshaft, cylinder and housing, etc., as well as 4 flexible production lines advanced at home for motorcycle engine, and a complete set of automatic inspection test eqiuipment for motorcycle engine

    計算機輔助設計輔助加工技術正在普遍使用。在非航空產品生產方面有大型壓鑄設備殼型鑄造，包括鍋桿輪磨在內的輪專用機床100多臺，以及活塞曲軸汽缸殼體等專業化生產線。此外，還建成了具有國內領先水平的4條摩托車發動機柔性生產線，以及成套的摩托車發動機檢測設備，可進行測試數據分析，改進檢定測試方法等。
  3. A calculation example is presented, and the maxi mum dynamic deflection of the beam bridge under the conditions of different speeds, different weights and different lengths of a vehicle is calculated

    分別分析了一輛汽車以不同車速、不同車重及通過不同跨徑橋梁時的情況，並給出了相應情況下的簡支梁橋跨中動位移的變化曲線。
  4. Based on these, the 200mw turbine unit of panxian thermal power plant is selected, and the key problems are analyzed, such as, selection of cool medium, flow path of medium, thermal stress during fast cooling etc. the cfd software is adopted, and the maximal thermal stress, the optimum cooling model and system, and the autocontrol scheme during fast cooling, are gotten. in the end, the results are applied in the site. the optimum cooling model and system, and the autocontrol scheme would be provided reference as the other similar units

    於此，本文以盤縣發電廠200mw汽輪機為研究對象，對發電廠汽輪機組空氣冷卻裝置及系統現狀深入分析基礎上，應用cfd軟體數值模擬了不同工況時汽輪機缸壁溫度變化情況，對200mw汽輪機快冷過程中控制指標進行分析，優化機組的快速冷卻過程，合理快冷設備、系統，優化控制曲線，分析最大熱應力值及最佳冷卻方式選擇，同時，對現有盤縣發電廠汽輪機組快速冷卻系統進行優化改進，並進行了實驗與實施。
  5. In this paper, the author improved the design of v trough of port plate by studying the automobile power steering pump ( apsp ) produced home and abroad and analyzing the different reasons of their noise from the stator transition curve, which could reduce the noise of apsp effectively

    本文以國內和國外生產的汽車動力轉向泵為研究對象，從定子過渡曲線的角度分析了它們噪聲不同的原因，並對配流盤v形尖槽進行了優化設計，可以有效地降低汽車動力轉向泵的噪聲。
  6. 3. bring forward a new idea : the ideology of synergetics used in atomic simulation and multi - scale simulation of materials design. on the basis of this, next tasks were put forward : ( 1 ) analyzing the changes of stress - strain curves of the interphase before and after pre - treatment ; ( 2 ) the efficient of the coupling effect of o2, na2s04 and h2o stream on the oxidation and erosion resistance of interphase ; ( 3 ) the methods of improving environment performance of interphase above 1273k

    提出將協同學的思想用於原子級模擬及跨尺度模擬的思路，並在此基礎上，提出下一步的工作設想： （ 1 ）分析熱處理前後界面相區域應力-應變曲線的變化； （ 2 ）航空發動機模擬環境中，氧、硫酸鈉蒸汽及水蒸汽耦合效應對界面相抗氧化性、抗腐蝕性的影響； （ 3 ） 1273k以上界面相環境性能提高的方法。
  7. Comparing the simulation curves with experiment curves, we found that they are similar. therefore, the dynamic mathematical model of the boiler steam - water system and its corresponding simulation model are valid

    通過模擬曲線與實驗曲線對比可知，模擬曲線與實驗曲線變化趨勢基本一致，說明所建立的船用鍋爐汽水系統數學模型以及基於該模型的模擬符合實際系統。
  8. First, the step response of the steam temperature process is obtained by experimentation, and the transfer function of the controlled process is calculated out using the step response data of the process. then, the pid parameters of the control system are optimized using the obtained process transfer function. finally, simulations are carried out to show the performance of the optimization - before system and optimization - after system

    首先通過現場試驗獲取過熱汽溫過程的階躍響應曲線，再根據試驗得到的過程階躍響應數據求取相應過程的傳遞函數模型；然後，根據傳遞函數模型進行控制系統pid參數的優化整定；最後，對優化前後的控制系統性能進行了模擬研究。
  9. Taking yangtian cxq3090 dump trucks as an example, this paper makes a detailed analysis on the situation of liquid - press oil - jar ' s swing angle and draws a diagram of curves to show the relationship of and according to the computer ' s data processing results

    摘要以揚天牌cxq3090型自卸車汽車為例，通過計算機數據處理，時其液壓油缸的擺動角度情況進行了詳細分析，並繪制出擺角與舉升角的變化關系曲線圖。
分享友人
分享到 Line

分享到臉書