油井停抽 的英文怎麼說

中文拼音 [yóujǐngtíngchōu]
油井停抽 英文
bumoff a well
  • : Ⅰ名詞1 (脂肪; 油脂) oil; fat; grease 2 (姓氏) a surname Ⅱ動詞1 (用桐油、油漆等塗抹) apply t...
  • : Ⅰ名詞1 (從地面往下鑿成的能取水的深洞) well 2 (形狀像井的東西) sth in the shape of a well 3 (...
  • : Ⅰ動詞1 (停止) stop; halt; cease; pause 2 (停留) stay; remain; stop off [over]: 船在錨地停了一...
  • : 動詞1 (把夾在中間的東西拉出; 提取) take out (from in between) 2 (從全部里取出一部分; 騰出) ...
  • 油井 : oil well
  1. Rational control of the pump ' s work and rest time is the key to solve the problem of void pumping. this essay gives theoretical analysis and cost comparison of every detective method, considers power detection as the most effective method, and puts forward several ways of power consumption and effectiveness power consumption at the same time. the designed electricity saving controller integrate all the above four methods, and it can work with different methods by switch between automatic and manual to broaden its accommodation

    解決現象的關鍵是合理控制開機時間與機時間長度,本文對各種檢測方法進行了理論分析及成本比較,認為功率檢測最行之有效,同時提出了功率檢測的幾種實現方法,即瞬時功率法、人工電耗法、設定功耗法及效益功耗法,所設計的節電控制器集以上四種方法於一身,可通過自動手動切換採取不同的功率檢測方法,使其適應范圍增寬。
  2. As crude oil is extracted continuously in oil field, there are more and more low yield oil wells in old oil field, and the problem of void pumping is becoming more serious. rational control of the pump ' s work and rest time can save electricity, prevent the break of beam hanger caused by beating liquid, and reduce attrition of the pump

    隨著田原的不斷開采,老田的低產越來越多,現象也越來越嚴重,合理地控制機的開機時間與機時間長度,可以達到節電、防止擊液引起的桿斷裂以及機磨損減少的目的。
  3. To prevent pumping system stopping working, working without efficiency and being destroyed, so it is very important to monitor oil - well. the thesis dissertates the process of developing displacement - load sensor which collects displacement data and load data to form the indicator diagrams, researches the means based on rbf neural network of recognizing fault types, designs parts of hardware and software of the mainframe of the oil - well monitor and control system, and debugs the entire oil - well monitor and control system

    為了防止機故障機、無、不法分子的蓄意破壞等情況的發生,因此對工況進行實時監控顯得尤為重要。本文論述了採集用於形成示功圖的位移和載荷數據的傳感器的研製,包括硬體電路和軟體的設計,對基於rbf神經網路的工況模式識別方法進行了研究,對監控系統主機的部分硬體電路及相應的軟體進行了設計,並對整個監控系統進行了聯調和測試。
分享友人