油櫃泵 的英文怎麼說
中文拼音 [yóuguìbèng]
油櫃泵
英文
oil tank pump-
Inside engine room frame # 14 # 16 portside, starboard side there is sea chest at each side, they are connected by main sea pipe, the sea water pump of main engine, auxiliary engine, general bilge pump, ballast pump, firefighting pump, condensator cooling water pump, and sea water pressure tank can suck sea water from them
機艙內# 14 # 16左、右舷設有海水閥箱各一個，用海水總管相連，可供主機、輔柴油機的海水泵、艙底總用泵、壓載泵、消防泵、冷凝機組冷卻水泵及海水壓力水櫃吸水。Turbine driven cargo oil pump lubricating oil tank
汽輪貨汪泵潤滑油櫃Automated teller machines ( atms ), pumps at gas stations, and fast - food outlet terminals are closed down because of unforeseen software snafus
自動櫃員機、汽油站的加油泵、快餐店終端機會因無法預見的軟體錯誤而崩潰。This system includes fuel oil tank, fuel oil pump, fuel oil hand pump, auxiliary engine daily service tank, piping and valves
本系統由燃油艙、燃油駁運泵、燃油手搖泵、輔機日用油櫃、管路及閥件等組成The second chapter simply introduces the development of alternate asynchronous inverter technology and retrospects some types of energy - saving systems for hydraulic elevators. then the working principles of the project are discussed and analyzed at four different working status, i. e. light load upwards, heavy load upwards, light load downwards and heavy load downwards. and the chapter focus on the introduction of structure design of pump station, calculation and type selection of pump / motor reversible units, research on oil leakage principles of accumulator circuit, design of accumulator - pump / motor pressure - energy transformer and integrated valve blocks, etc. the last but not the least, the electrical wiring of vector inverter control cabin and design of computer control and data acquisition system are introduced
論文第二章首先簡單介紹了交流異步電動機變頻調速技術的發展概況，在回顧電梯液壓控制系統節能技術的基礎上，介紹了本課題研製的「採用蓄能器的液壓電梯變頻節能控制系統研究」的基本原理，分析了動力系統在電梯轎廂輕載上下行、重載上下行等四種典型工況下的基本工作狀態和工作方式；詳細地介紹了本課題節能系統液壓動力泵站的結構設計和參數設計，重點研究了液壓動力泵站的結構設計、液壓泵馬達可逆性問題及其選型設計計算、蓄能器迴路泄漏油損失機理的研究及其補償裝置的設計、蓄能器-泵馬達壓力能量轉換裝置的設計、多功能集成控制閥組的設計等內容；最後簡單介紹了本課題矢量控制變頻控制櫃的外部附件電氣接線、計算機控制及數據採集系統的硬體設計等內容。Based on this method, design the system oil circuit and constant - pressure hydraulic power station as well as the hydraulic manifold block, measuring platform, electrical cabinet and reclaiming oil tank
在此油源方案的基礎上，設計出測量系統油路、油源泵站系統，同時進行了液壓集成塊、測量臺架、電氣控制櫃和漏油回收油箱的設計。分享友人