油管靜壓 的英文怎麼說

中文拼音 [yóuguǎnjìng]
油管靜壓 英文
sthp
  • : Ⅰ名詞1 (脂肪; 油脂) oil; fat; grease 2 (姓氏) a surname Ⅱ動詞1 (用桐油、油漆等塗抹) apply t...
  • : Ⅰ名詞1 (管子) pipe; tube 2 (吹奏的樂器) wind musical instrument 3 (形狀似管的電器件) valve;...
  • : Ⅰ形容詞1. (安定不動; 平靜) still; calm; motionless 2. (沒有聲響; 清靜) silent; quiet Ⅱ名詞(姓氏) a surname
  • : 壓構詞成分。
  • 油管 : [石油工業]1. (輸油管道) oil pipe 2. (井架用的油管) oil tube
  1. Its current products include : top oscillation electrical precipitator, side electrical oscillation precipitator, magnetism controlled static electricity precipitator, wet electrical precipitator, honeycomb electric catching tar instrument, high - pressur silicon rectifier equipment and plc low - pressure controlling system, blast furnace gas impulse precipitator, high concentration pulverized coal collector, coke oven and boiler flue gas low pressure impulse precipitator, blower fan inhaler, crossing piping gas cooler, high temperature fume cooler, gyre - orientation impulse hop - pocker and all sorts of molded sections

    目前主要產品有:頂部振打臥式電除塵器、側部振打電除塵器、磁控電除塵器、濕式電除塵器、蜂窩電捕焦器、高硅整流裝置及plc低控制系統、高爐煤氣脈沖除塵器、高濃度煤粉收集器、焦爐及鍋爐煙氣用低脈沖除塵器、風機空氣過濾器、橫式煤氣冷卻器、高溫煙氣冷卻器、回轉定位脈沖大布袋及加工各種冷彎型鋼。
  2. A noise control in static hydraulic test for tubing

    試驗系統的噪聲控制
  3. Air filtration portfolio, air filters, valve, oil mist machine, filter valve, oil mist separator, micro - mist separator, stability activated solenoid valve, pressure gauge, micro - valve and vacuum valves, links the release of the closure - pressure valves, and pipe connection, a one - way valve, t - shelves, shelves, brackets, diaphragm - type flow switches, blades type flow switches, further growth actuator, the valve lock, precision valve, pressure switches, mechanical pressure switches, pneumatic control ratio positioning devices, and electric - gas ratio positioning devices, and telecommunications - pressure converters, electro - pneumatic proportional valve, filter valve, shuttle valve, gas - electric relay and gas indicator, delay pneumatic valve and cylinder fcl, plumbing fcl, mufflers and exhaust cleaner, the excess flow valve with silencer, a one - way valve, rapid valve, rapid joints, rapid valve with fcl, rapid joint sub - cluster gas, micro joints, gas pipes, pipe from the devices, and helical coils, pipes, channels, scissors, multiple fastener, high - speed rotary joint, 10000 threaded joints, and insert the tube joints, rotary joints began, 68. 25 rapid joints and hoses, hose fittings and rapid non - electrostatic

    空氣過濾組合空氣過濾器減霧器過濾減霧分離器微霧分離器穩定啟動電磁閥力表微型減閥減氣閥三通釋放式截流閥力開關接頭單向閥t型隔板隔板托架膜片型流量開關漿葉型流量開關增速繼動器鎖定閥精密減力開關機械式力開關氣控比例定位器電-氣比例定位器電訊號-氣轉換器電-氣比例閥過濾減閥梭動閥氣-電繼電器氣源指示器氣動延時閥氣缸限流器道限流器消聲器排氣潔凈器限流閥帶消聲器單向止回閥快速排氣閥快速接頭快速排氣閥帶限流器快速接頭集束分氣微型接頭氣喉脫離器螺旋道剪刀多扣件高速旋轉接頭萬用螺紋接頭插入式接頭旋式緊鎖接頭難燃性快速接頭和軟不帶電快速接頭和軟
  4. Methods of test for rubber and plastics hoses and hose assemblies - hydraulic pressure tests - hydrostatic tests for oil suction and discharge hose

    橡膠和塑料軟組件的試驗方法.第102部分:液試驗.第10節:吸和放試驗
  5. The construction of conical nozzle is used by pump ' s delivery - valve, making use of the dynamic characteristics of conventional. short pipe to enhance injection pressure. there are three parameters of fuel injection system : response pressure, injection - advanced angle, injection valve bulge high degree, the best match was found by adjusting them

    泵出閥端,採取漸縮結構措施,利用路動態效應提高噴力;對于噴系統參數:噴力、態供提前角和嘴凸出高度,三個參數進行調整試驗,找到它們的最佳匹配。
  6. Finally, the paper expatiates the realization process of this design, including the rotation equipment management, the static equipment management, examines and service project management, the electrical management, the meter computer management, the water quality management, the lubricating oil management, the static seal management, the craft pipeline management, the bearing management, the pressure vessel

    最後,文章對系統的設計實現過程進行了闡述,分別對大慶石化總廠設備理系統的轉動設備理、設備理、檢維修計劃理、電氣理、儀表計算機理、水質理、潤滑理、密封點理、工藝理、軸承理、力容器理、安全閥理進行重點描述。
  7. This way is still a practical approach to measure static pressure in horizontal wells, though needed to be im proved, producing mechanically with deep & deeper pay zones

    這一方法還有待進一步完善,但它不失為一種塔里木田目前機采深層水平井測的實用方法。
  8. Let the air dissolve for over 2 minutes. after the pressurized saturated liquid is fully mixed with the wastewater in the stagnant mixer, discharge the mixture into the floatation tank for solid and liquid separation and achieve the goal of grease and waste removal

    分鐘以上,經加之飽和污水于態攪拌中與待處理之污水充分混合後排入浮除槽進行固液分離,而達到去除脂或其他污物之目的。
分享友人