油罐壓力計 的英文怎麼說

中文拼音 [yóuguànyālìjì]
油罐壓力計 英文
tank pre ure gauge
  • 油 : Ⅰ名詞1 （脂肪; 油脂） oil; fat; grease 2 （姓氏） a surname Ⅱ動詞1 （用桐油、油漆等塗抹） apply t...
  • 罐 : 名詞1. （罐子） jar; jug; pot; tank; tin 2. （煤礦用裝煤車） coal tub
  • 壓 : 壓構詞成分。
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  1. Modbus transducer is the key device in the system and is used to offer power supply of pressure and temperature sensor, to collect signal, to linearizate and compensate temperature, to calculate density, volume and mass, to transmit data to modbus network, and display the data. so the modbus transducer is a multi - parament measurement, intelligent control device which can manage multi - signal

    變送器是系統的核心設備，其作用是為油罐溫度、壓力、液位、可燃氣濃度等傳感器供電，採集傳感器信號並進行線性化、溫度補償等處理，完成密度、體積和質量等參數計算，將數據輸出到modbus現場總線測控網路，根據需要現場顯示計測量參數。
  2. Through consulting lots of relevant references, present research of direct drive volume control hydraulic servo system is summarized in this paper, the principle and character of this system are expatiated, the principle of vector control is introduced. at the same time, the mathematical model of ac asynchronous motor is set up based on the vector control theory. the mathematical models of both the pump controlled motor and pump controlled cylinder are set up and simulated in this paper

    在查閱大量國內外相關文獻的基礎上，本文綜述了國內外對該系統研究概況，闡述了該類系統原理和特點;闡述了矢量控制的基本原理，並基於這一原理建立交流異步電動機的數學模型;分別建立了泵控馬達系統和泵控缸系統的數學模型，並給出了模擬分析;設計了用於泵控馬達系統的集成閥塊，加工了密閉壓力油罐;針對現有直驅式電液伺服裝置所存在的問題，本文主要針對系統工作過程中所產生的噪音與爬行問題進行了一定的研究。
  3. Based on comparison of several technical schemes, the method of sand bedding pre - elevating and step water - filling pre - compressing is adopted. so the dissertation is consist of two parts : ( 1 ) the applicability study for the method of sand bedding pre - elevating and step water - filling pre - compressing, including numerical analyses for the thickness of sand bedding, the consolidation, settlement and stability of foundation, drainage, possibility of foundation liquefaction under seismic loading, et al. ( 2 ) monitoring at construction stage and checking the effect of foundation treatment, including the measurements of the settlement velocity and non - uniform settlement of ring beam under the tank, pore pressures and horizontal displacements in foundation, the pressure distribution at the bottom of oil tank and the strength increase of soils

    通過多種技術方案比較，最終選擇了技術先進的砂墊層預抬高分級充水預壓法，論文工作主要由以下兩部分組成： （ 1 ）砂墊層預抬高分級充水預壓法的適用性研究，其中包括砂墊層厚度、地基沉降與固結度、地基穩定性、降水、地震作用下砂土液化的可能性等方面的計算分析； （ 2 ）施工監測與地基處理效果檢驗，其中包括油罐環梁基礎沉降速率與不均勻沉降程度、各分級充水加載階段地基超靜孔壓與深層水平位移、油罐底板壓力分佈及地基土強度增長等方面的實測與數據分析。
  4. Based on the request in 99 version of supervisory code and the example of stress corrosion crack appeared in the liquefied oil tank, the problem of the metal local corrosion involved in the design of pressure vessels was discussed in this article

    本文結合99版「容規」的新要求，以液化石油氣儲罐所涉及的應力腐蝕開裂為例，討論了化工壓力容器設計中涉及的金屬局部腐蝕問題。
分享友人
分享到 Line

分享到臉書