油罐設計 的英文怎麼說

中文拼音 [yóuguànshèjì]
油罐設計 英文
tank design
  • 油 : Ⅰ名詞1 （脂肪; 油脂） oil; fat; grease 2 （姓氏） a surname Ⅱ動詞1 （用桐油、油漆等塗抹） apply t...
  • 罐 : 名詞1. （罐子） jar; jug; pot; tank; tin 2. （煤礦用裝煤車） coal tub
  • 設 : Ⅰ動詞1 （設立; 布置） set up; establish; found 2 （籌劃） work out : 設計陷害 plot a frame up; fr...
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 設計 : devise; project; plan; design; excogitation; layout; layout work; styling
  1. It is pointed out that the immersible pump - based fuelling process can realize the multi oil gun on the one pump basis under the condition of positive pressure, which makes the design of fuelling station more flexible and is a development tendency in modern fuelling station

    指出採用自吸泵型加油機的加油工藝存在弊端，而採用潛油泵加油機的加油工藝，可以實現一泵多槍，油罐正壓出油，技術先進，工藝簡單，使加油站設計更加靈活，是現代化新型加油站的技術發展趨勢。
  2. Design of a monitoring system for an oilcan based on kingview

    基於組態王的油品罐區監視系統設計
  3. Modbus transducer is the key device in the system and is used to offer power supply of pressure and temperature sensor, to collect signal, to linearizate and compensate temperature, to calculate density, volume and mass, to transmit data to modbus network, and display the data. so the modbus transducer is a multi - parament measurement, intelligent control device which can manage multi - signal

    變送器是系統的核心設備，其作用是為油罐溫度、壓力、液位、可燃氣濃度等傳感器供電，採集傳感器信號並進行線性化、溫度補償等處理，完成密度、體積和質量等參數計算，將數據輸出到modbus現場總線測控網路，根據需要現場顯示計測量參數。
  4. Design methods for tanks of tank cars

    油罐車罐的設計方法
  5. Through consulting lots of relevant references, present research of direct drive volume control hydraulic servo system is summarized in this paper, the principle and character of this system are expatiated, the principle of vector control is introduced. at the same time, the mathematical model of ac asynchronous motor is set up based on the vector control theory. the mathematical models of both the pump controlled motor and pump controlled cylinder are set up and simulated in this paper

    在查閱大量國內外相關文獻的基礎上，本文綜述了國內外對該系統研究概況，闡述了該類系統原理和特點;闡述了矢量控制的基本原理，並基於這一原理建立交流異步電動機的數學模型;分別建立了泵控馬達系統和泵控缸系統的數學模型，並給出了模擬分析;設計了用於泵控馬達系統的集成閥塊，加工了密閉壓力油罐;針對現有直驅式電液伺服裝置所存在的問題，本文主要針對系統工作過程中所產生的噪音與爬行問題進行了一定的研究。
  6. Design of the double floating suction in 10 000 m3 inner floating roof tank

    3內浮頂油罐雙浮動吸油裝置設計
  7. Road tankers in reinforced plastic. symbols used for design

    增強塑料制公路油罐車.設計用符號
  8. Code for design of sphere tank foundation in petrochemical enterprises

    石油化工企業球罐基礎設計規范
  9. Welded steel tanks for liquefied petroleum gas - road tankers - design and manufacture

    液化石油氣焊接鋼罐.槽罐車.設計和生產
  10. Fini air treatment systems for the woodworking industry are composed of refrigerating dryers, filters for separating impurities, condensate drain cocks, water - oil separators, tanks, and all other components necessary for adapting the compressor room to the needs of the sector

    木工行業的fini空氣處理系統由冷藏乾燥器組成，分開雜質的過濾器，直立式排水道，水油分離器，氣罐和其他組成部分都為適應壓縮機房的需要而設計。
  11. Our specialties are supply equipment, tanks, instrumentations, control system, piping and design for petrochemical product use

    我們的專業為，供應石油化學產品所需之設備、儲罐、電器儀表、控制系統、工業渠道及工程設計。
  12. Analyzed and discussed the project design of larger oil tank and its ground treatment with cots of project instances, and put forward a design method of larger oil tank and some practical experience about ground treatment

    摘要結合工程設計實例，對大型油品儲罐基礎及其地基處理的工程實例進行了分析探討，提出大型油品儲罐基礎設計方法及其地基處理方面的實踐經驗。
  13. Static welded cylindrical tanks, serially produced for the storage of liquefied petroleum gas having a volume not greater than 13 m3 and for installation above ground - design and manufacture

    安裝在地面上的儲存容量不超過13m的成系列生產的液化石油氣儲存用固定焊接圓柱形氣罐.設計與製造
  14. Static welded steel cylindrical tanks, serially produced for the storage of liquefied petroleum gas having a volume not greater than 13 m3 and for installation above ground - design and manufacture

    安裝在地面上的儲存容量不超過13m的系列生產的液化石油氣儲存用固定焊接鋼制圓柱形氣罐.設計與製造
  15. Abstract : an analysis on the damage of flame arrester of oil tank has been made from its structure as well as daily care. countermeasures against its disability have been presented, that is, casting the two semi - casing into one piece, leaving out the intermediat flanges, thickening the casing, and increasing the casting round - angle between the flanges and casing. in this way, the strength of casing can be enhance and local stress will be decreased. in addition, in order to enlongate the service life, the operating frequency of flame arrester should be properly reduced in daily care

    文摘:從設計結構及維護保養的角度分析了儲油罐阻火器損壞的原因，並提出了相應的改進措施，即在結構方面可以將阻火器外殼鑄為一體，省去中間法蘭，增加殼體厚度，加大法蘭與殼體之間的鑄造圓角，以增加強度減少局部應力:在維護保養方面，應適當減少操作次數，延長阻火器的使用壽命。
  16. An example of data acquisition from mass meters in tankfarm in refinery with radio modem is introduced. the systems hardware and software are described

    介紹了一個利用無線遙測方法對煉油廠罐區質量流量計實現數據採集的實例。描述了該系統的硬體組成和軟體設計方法。
  17. It is demonstrated by geologic survey data that the bearing capability and deformation of natural foundation are out of the scope of the required values, which means the natural foundation has to be treated

    地質勘測資料表明天然地基不能滿足油罐設計的承載力與變形要求，必須進行處理。本論文選題密切結合這項大型工程建設項目。
  18. Design specification for safety of liquefied hydrocarbon spherical tanks

    石油化工液化烴球形儲罐設計規范
  19. Code for design of vertical cylindrical welded steel oil tanks

    立式圓筒形鋼制焊接油罐設計規范
  20. Design specification for oil removal tank

    除油罐設計規范
分享友人
分享到 Line

分享到臉書