油計量系統 的英文怎麼說

中文拼音 [yóujìliángxìtǒng]
油計量系統 英文
oil-metering system
  • 油 : Ⅰ名詞1 （脂肪; 油脂） oil; fat; grease 2 （姓氏） a surname Ⅱ動詞1 （用桐油、油漆等塗抹） apply t...
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 統 : Ⅰ名詞1 （事物間連續的關系） interconnected system 2 （衣服等的筒狀部分） any tube shaped part of ...
  • 計量 : calculate; estimate; meterage; metering; batching; measure
  • 系統 : 1. （按一定關系組成的同類事物） system 2. （有條理的;有系統的） systematic
  1. This thesis described fuel management system theory and system reliability design to set forth system fuel management general design thought. many technical details are discussed in the thesis such as : fuel quantity measurement, fuel mass character calculation, fuel density measurement, the accuracy of fuel quantity measurement, the optimum location of fuel gauge probes in the fuel tank. the author brings forward a new method which is based on the software of catia to calculate fuel mass character

    本文對燃油管理系統的工作原理和可靠性設計等問題進行研究，以明晰燃油管理系統的總體設計思路；並對數字式燃油量測量、燃油質量特性計算、燃油密度測量、提高燃油量測量精度的措施、油箱油量傳感器安裝位置優化等具體技術展開研究；提出了一種基於catia軟體的燃油質量特性計算方法；論文最後探討了燃油管理系統的未來發展方向。
  2. The gascat gips / gdps series of automatic shutoff valves are used as the main safety device for transmission, distribution and measurement of natural gas or lpg gas system protection, and for non - corrosive gas systems in general

    升壓感應關斷型?與gdps ?降壓感應關斷型?系列自動關斷閥適用於天然氣或液化石油氣之輸送、配氣與計量系統，還有一般無腐蝕瓦斯氣體系統保護的主要安全設施。
  3. A practical measurement for oil tank storage

    一種實用的油罐儲量計量系統
  4. Error analysis and improvement for oil tank measure system

    儲油罐計量系統中精度的分析及提高
  5. There is many a method to measure oil concentration, but the commonly used one is infrared absorbance luminosity method, so firstly the article illustrates fundamental of absorbance luminosity method for quantitative analysis - lambert beer law, and puts up with the basic model for system measurement, and then designs measure logic of system

    關於水中油含量的檢測有多種方法，最常用的是紅外吸光光度法，本文對吸光光度法在物質定量分析中的基本理論? ? lambert - beer定律做了簡要介紹，並以此提出了系統測量的基本模型，進而設計了系統的測量邏輯。
  6. The system uses the pc and the at89c52 as the control center of the system. the pc optimizes the control parameters as the calculation control unit. the at89c52 receives the various parameters by serial communication with the power measurement system and the fuel consume measurement system and the emission measurement system and the ecu and so on, then sends into pc by sharing the ram with the pc as the communication control unit

    該系統採用pc機和單片機at89c52為上位機，以pc機作為計算控制單元，對發動機控制參數進行優化；單片機作為通訊控制單元，與作為下位機的測功器加載系統、油耗測量系統、排放測量系統以及發動機電控單元ecu等子系統進行串列通訊接收各參數，並通過與pc機共享ram送入pc機。
  7. Fist ly, use mass equivalent method to predigest the original rotor system. secondly, use transfer matrix arithmetic to have finished the relative program to calculate the critical speed of flexible multi - tray rotor bearing system by matlab language. thirdly. finish program the unbalance response using riccati - transfer matrix arithmetic and finity buck arithmetic. fourthly, answer to the high vibration of uncontroled system when cross the critical speed, come out to adopt changing clearance damper bearing to control the viberation

    本文對多柔盤轉子-支承系統的振動現象做了以下初步探索：用質量離散化方法把原轉子系統簡化；採用matlab語言編制了對傳遞矩陣法計算多柔盤轉子-支承系統的臨界轉速；用matlab語言對riccati傳遞矩陣法和有限元法編制了程序計算系統的不平衡響應；並針對其過臨界轉速時振動較大的現象，提出採用變間隙控制油膜剛度和阻尼，從而使原系統的在特定轉速（臨界轉速）的一段范圍內不平衡響應減小；並從被動控制與主動控制兩方面進行數值模擬，取的了較好的控制效果。
  8. The oil loading system and the management of oil bin in the oil - bin area is intensive and the measurement method is under - developed at present time. in order to resolve this problem and realize the automatic management, this thesis analyzed the demands of the system, and then integrated the optical fiber sensing technology, the advanced computer technologies of hardware and software, the technologies of intelligent instrument, auto - control and communication ; finally a distributed and intelligent monitoring system of the automatic oil - loading system was developed. the thesis contains hardware design, software design and communication design

    為了解決罐區裝車手動付油與油罐手工檢尺測量勞動強度大，方法落後以及油庫安全性要求非常高的問題，提高油庫自動化和信息化管理水平，本文從監控系統用戶需求與功能分析入手，結合當前飛速發展的光纖傳感技術、計算機軟體、硬體技術、智能儀表技術、自動控制技術和通訊技術，開發了一套用於石化行業的基於光纖傳感技術的集自動付油管理及儲油液位、溫度等安全檢測功能於一體的油罐庫區自動付油管理系統。
  9. Then the paper estimates the parameter of the model with different techniques such as econometrics and emulates the seaborne volume system of china petroleum exports and imports in 2010 with vensim

    然後應用經濟計量學等多種方法對模型參數進行估計，並運用vensim模擬語言對2010年中國石油進出口海運量系統進行模擬模擬。
  10. Meanwhile, the paper analysis shortage of the methods commonly used heating insulating oil, investigate principles of traditional pid control and fuzzy control, integrats the advantage of two control algorithms, makes use of fuzzy + pid control algorithm to control insulating oil temperature, and has designed fuzzy + pid controller. through matlab simulation, validates that wavelet hard threshold vale de - noise method can effectively reduce the impact of random disturbance

    同時，論文分析了常用加熱絕緣油方法的不足，在研究傳統pid控制和模糊控制原理基礎上，綜合兩種控制演算法的優點，在絕緣油介損測量系統中，提出採用模糊+ pid控制演算法對絕緣油溫度進行控制，並實現了模糊+ pid控制器的設計。
  11. To meet the requirements of engineering and after reviewing the previous results, the author deeply researches measurement of water ratio in oil - water two phases system based on the principles to analyze two phases fluid. with present mature computer technology a system to measure water ratio in oil - water two phases is successfully developed and the procedure is worth introducing here according to the data from relative experiments

    本文從實際工程需要出發，查閱並繼承了前人研究的理論成果，運用兩相流動基本分析方法，進一步對油品含水測量進行深入研究，結合當前成熟的計算機技術，成功研製出將油品含水率測量系統。
  12. Based on this method, design the system oil circuit and constant - pressure hydraulic power station as well as the hydraulic manifold block, measuring platform, electrical cabinet and reclaiming oil tank

    在此油源方案的基礎上，設計出測量系統油路、油源泵站系統，同時進行了液壓集成塊、測量臺架、電氣控制櫃和漏油回收油箱的設計。
  13. Discharge coefficient is the important factor of influencing sucker rod pump performance. the discharge coefficient is calculated, and the main influencing factors are analyzed

    本文對有桿抽油泵的排量系數進行了詳細的計算，系統地分析了影響排量系數的主要因素。
  14. The results of the experiments has shown : the lpg / diesel dual fuel engine has kept its high power performance and reduced its emissions, especially the soot and nox after the fuel - supplied system has been set up ; the fuel economy performance has been improved at some degree when high load ; however, when lpg ratio increased, the engine showed the trend of violence for high compression ratio

    試驗結果表明：在採用了自行設計的聯動式燃油供給系統后， lpg柴油雙燃料發動機在保持原機高功率的同時，排放量，尤其是碳煙和no _ x有大幅度的降低；在高負荷時，其燃油經濟性也有相當的提高。但當lpg的摻燒比加大到50以上時，會出現工作粗暴的傾向。
  15. So it could be used for level control and measurement of flammable and explosive oil and other chemical liquids, specially for the precise measurement of liquid level in small tanks

    該傳感器可廣泛應用於石油化工系統的多種液體的液位控制和測量，特別適用於小型容器的液位精確計量。
  16. The kdd ( knowledge discovery from database ) technology is used to mining the design coefficient to support the model - based design

    由於燃油噴射系統的復雜性，設計模型中存在大量的經驗系數。
  17. The defects can be improved by using digital fuel management system which is based on fuel management computer to perform fuel quantity gauging, fuel system control and data management. digital fuel management system is the future of aircraft fuel system

    採用以燃油管理計算機為核心的數字式燃油管理系統，對燃油系統實施油量測量、系統控制和數據管理，很好地解決了模擬式系統的缺陷，是飛機燃油系統發展的必然趨勢。
  18. In this paper, it firstly expatiated on the application of decision support systems in domestic and international, introduced the basic theory of decision support systems, raised the main models of the output and cost optimal allocation, focused on the system analysis, system design and system deployment base on the unified modeling language, and then listed some running instance of the dss

    文中首先闡述了決策支持系統在國內外及油田企業的應用現狀，介紹了決策支持系統的基本理論，給出了應用於產量成本優化配置的主要模型，並重點闡述了基於uml的產量成本優化配置決策支持系統的系統分析、系統設計和系統部署的建模，然後給出了系統的運行示例。
  19. The main target of the research is to design and manufacture a cat ( computer aided test ) system of joint internal thread, in order to improve the measuring accuracy and quality of the joint internal thread of bao steel inc. this paper analyzes the success and limitation of the former design, and introduces a double probe system

    本文目的是研究開發一套接觸式油管接頭內螺紋計算機測量系統，滿足寶鋼公司提出的內螺紋檢測的要求。論文在分析前人研究設計中的成功經驗和不足的基礎上，提出了雙針測量的系統方案，並對測量系統的數字濾波、演算法模型和誤差分析進行了深入的研究。
  20. Fuel metering system

    燃油計量系統
分享友人
分享到 Line

分享到臉書