泡沫分選 的英文怎麼說

中文拼音 [pāomòfēnxuǎn]
泡沫分選 英文
froth separation
  • 泡 : 泡Ⅰ名詞1 （氣泡） bubble 2 （像泡一樣的東西） sth shaped like a bubble Ⅱ動詞1 （較長時間地放在液...
  • 沫 : 名詞（沫子） foam;froth; lather
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 選 : Ⅰ動詞1. （挑選） select; choose; pick 2. （選舉） elect Ⅱ名詞（挑選出來編在一起的作品） selections; anthology
  • 泡沫 : foam; froth; spume; yeast; bead
  1. Classification and froth flotation of fly ash for producing high - quality pozzolan

    採用分級和泡沫浮選從飛灰中生產高質量白榴火山灰
  2. Methods for froth flotation testing of hard coal - laboratory procedure

    硬煤泡沫浮選試驗方法.第1部分:實驗室規程
  3. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
  4. This thesis preliminarily researched drilling technology of applying foaming dth hammer into hydrology and waterwell drilling beginning with analyzing foaming dth hammer ' s structure characteristics and working principle and joining together with the indoor experiment with respect to the fitting of drilling equipments, designing of grouting system, selecting of drilling program parameters and so on

    從分析泡沫潛孔錘的結構特點和工作原理出發，結合室內實驗，在鉆進設備的配套、灌注系統的設計、鉆進規程參數的選擇等方面，對泡沫潛孔錘應用於水文水井鉆探的鉆進工藝進行了研究。
  5. An image segmentation of flotation froth based on watershed transformation

    基於分水嶺變換的浮選泡沫圖像分割
  6. Concentration distributing mathematical model of continuous foam separation tower in whole tower

    連續式泡沫浮選分離塔全塔濃度分佈的數學模型
  7. In the paper, three methods of evaluation of cushioning properties and energy - absorption capability of low density porous material are discussed, and a mew method of evaluation of damping of vibration is introduced, taking silicone rubber foam as an example, the use of these methods in rational choice materials and priority design is expounded

    摘要本文對低密度多孔介質緩沖吸能特性的三種評估方法進行了分析，進而提出了評估其減振特性的剛度曲線方法，並以泡沫矽橡膠為例，具體闡述了上述評估方法在合理選材、優化設計中的應用。
分享友人
分享到 Line

分享到臉書