波形測試 的英文怎麼說

中文拼音 [bōxíngcèshì]
波形測試 英文
waveform testing
  • 波 : Ⅰ名詞1 （波浪） wave 2 [物理學] （振動傳播的過程） wave 3 （意外變化） an unexpected turn of even...
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 波形 : [物理學] wave form; shape; wave pattern; wave profile
  • 測試 : test; testing; checkout; measurement
  1. When measuring the magneto performance parameter ， we find that the instrument which use to measure voltage and current is still the simple voltmeter and amperemeter in the national standard ， and the form of wave that we observed is anomaly. based on the measure principles, it obviously ca n ' t be used to do quantitative analysis ； because the discharge process of ignition system is quite complex, accompanies with very strong electromagnetism interference, and the ignition current and voltage are variable ， it make the measure of ignition energy become a difficult thing of ignition system performance detection

    在磁電機常規測量時，發現在國家標準中用於測量電壓、電流的儀器仍然是普通的電壓、電流表，而觀測到的波形多為不規則的形狀，根據測量原理，顯然不能用其來做定量的分析；由於點火系統的放電過程比較復雜，伴隨著很強的電磁干擾，點火電流、點火電壓都是變量，使得點火能量的測量成為點火系統性能測試的一個難點。
  2. Given the abilities of generating all kinds of ideal and not ideal signals, it has been widely used in the domains of communication, radar, navigation and astronavigation

    它可以產生各種理想及非理想的波形信號，是電子工程師、生產線以及教學科研的重要測試設備，廣泛用於通信、雷達、導航、宇航等領域。
  3. This paper discusses the designing and making of the dynamic testing systems of engine electronic control system. base on the construction and operation principle of santana 2000gsi m3. 8. 2 engine electronic control systems, design and manufacture led circuit of dynamic testing and fault imitating electronic control unit. on the inspect board, design and equip with motronic 3. 8. 2 ecu i / o measuring joints, design and set up obd - ii diagnostic communication link, design and install fuel pressure inspecting meter. depend on the obd - ii diagnostic communication link and ecu i / o measuring joints, this dynamic testing system can inspect engine electronic fuel injection system, distributorless ignition system, idle speed control system and evaporative emission control system, and can inspect m3. 8. 2 sensors, ecu and actuators, and can interrogate fault memory and erase fault memory ; and can analyse data stream ; and can carry out fault imitating. besides, this paper analyses sensors and actuators typical fault w aves

    2電控單元電路連接器設計製成輸入輸出電子控制檢測端子，並在檢測面板上布置了obd -診斷插座和燃油壓力表。使該動態測試系統能實現對電噴發動機的燃油系統、直接點火系統、怠速控制系統和燃油蒸氣排放控制系統的動態檢測；並通過obd -診斷座、 ecu輸入輸出檢測端子和故障模擬處理單元實現對電噴發動機電控系統各傳感器、電控單元、執行器進行故障碼讀取與清除；動態數據讀取和波形測試和故障模擬等。此外，本論文還分析了傳感器和執行器典型故障波形。
  4. According to the system technology require, adopting singlechip realize open loop digital control of hdclsm ; using v / f conversion and complex key - control method realize digital setting of system parameter, such as velocity ; using micro - stepping control insure the motor running more smoothly ; adopting debasing speed control method to eliminate the mechanical impact of distance termination effectively ; at the same time, analyzing main power circuits drive circuit and protect circuit of system, completing hardware design and facture and software programming and debugging ; at last, making a whole test in hybrid rotary step motor. the experiment result indicates that this control system reaches the qualities required and run smoothly also

    根據系統技術要求，採用單片機實現了混合式直流直線步進電動機的開環數字控制；利用v f變換和復合鍵控方法實現了系統轉速等參數的數字設定；利用細分控制技術保證了電機運行的平穩性，並進行了波形分析和理論研究；採用單片機軟體降速控制策略解決直線步進電機行程末端的機械沖擊問題；同時對主功率電路、驅動電路和系統保護電路進行了分析，完成了硬體設計、製作和軟體編程、調試，最後在混合式旋轉步進電動機上進行了全面測試。
  5. In order to reduce time in this procedure, we realize a fast cyclization algorithm based on the hash table. experimental results show that this approach is efficient and automated in test vector translation

    實驗結果表明，在此波形格式基礎上的測試向量轉換，不僅在速度上得到提高，同時針對大容量的測試向量集合，也能獲得較高的壓縮結果。
  6. The experiment apparatus has been developed, which is based on software ( labview ) and hardware ( pci board ni 6024e ). the displacements and generative force at the tip of the ipmc actuators were measured with respect to the different voltages, frequents and various waveforms which include square, sinusoidal, and triangular wave

    實驗選取了不同電壓幅值，不同頻率的方波、三角波、正弦波三種波形作為電激勵信號，利用高速攝像記錄ipmc的位移變形，並通過力傳感器實測了ipmc試樣末端的輸出力。
  7. The function of ppi ( programmable parallel interface chip ) 8255 is realized through emulating the key waves and testing a chip

    通過波形模擬、下載晶元的測試，完成了計算機可編程并行接晶元8255的功能。
  8. First, this paper gives a method, which is utilized by baseband system according to wcdma system capability requirements, using asic + dsp to realize raker, using dsp + dsp to realize symbol process. the hardware structure of asic + dsp and dsp + dsp is designed from the whole design view. then, the discussion is made of the main function module of ic2001 and dsp, hi module, dsp peripherals on chip such as hpi, edma and emif

    文章首先結合wcdma系統性能要求提出了基帶系統所採用的方案，由asic + dsp實現rake接收機功能和dsp + dsp實現符號級處理功能;然後從總體規劃的角度設計出asic + dsp和dsp + dsp系統硬體結構，對ic2001和dsp的主要功能模塊， hi模塊， dsp片上外設hpi口、 edma和emif總線作了分析，並結合基帶處理功能開發了系統驅動;最後由信號源發出測試數據進入系統，進行功能實現后輸出數據繪制出波形圖，對所設計的基帶系統驅動方案進行驗證分析。
  9. Therefore rath may be used as an exploratory tool to test a given equation has solutions of the assumed form

    因此rath可作為一個測試非線性演化方程是否擁有雙曲正切多項式形式的孤波解的有效實用的工具。
  10. This paper starts the research of the liquid floated pendulous accelerometer testing system according to the engineering. at first, this paper gives the brief introduction of the history and present status of accelerometer and its testing technology, the working principium and math model of the liquid floated pendu - lous accelerometer, and then, decides the binary width pulse force retrim loop as the design proposal of testing system, researches the transfer function of every part in the system emphasizly, analyses the stability of the whole accelerometer testing system from the angle of control theoretics by the open loop transfer function of system, and designed the correcting net, analyses the basal problems such as resolution, sampling restraint, precision and so on, designs the hardware testing circuits such as preamplification, band - pass filter, alternating amplifier, phase sensitive demodulatorn, pulse - width modulation, frequency scale circuit, moment current generator. finally, using the graphics program language labv - iew which is designed for testing field especially by ni accomplishes the solfware design of testing system, realized the testing functions

    首先對加速度計及其測試技術的發展歷史和現狀，液浮擺式加速度計的工作原理和數學模型等作了簡要的介紹，然後確定了以二元調寬脈沖再平衡測試迴路為設計方案，並從控制理論的角度進行了分析，著重研究了系統中各部分的傳遞函數，利用系統開環傳遞函數分析了系統的穩定性，同時設計了系統的校正網路;分析了二元調寬脈沖再平衡測試迴路的解析度、采樣約束以及測試精度等基本問題，並按照系統分析的結果設計了包括前置放大、帶通濾波、交流放大、相敏解調、脈寬調制、頻標電路以及力矩電流發生器等測試系統各部分硬體電路，驗證了電路的正確性，最後按照測試系統的要求，採用了美國ni公司專為測試領域所開發的虛擬儀器工具? ? labview作為測試軟體開發工具，利用該圖形化編程語言完成了測試系統軟體部分的設計，實現了測試功能。
  11. Nowadays, the ways to detect the piles are various, and all of them are limited in some aspects. for instance, coring test do large scathe on the piles, and static load test will waste much time, money and energy, while some ways are hard to operate as the limitation of the length and the diameter of the piles, and the special condition on the spots, such as high - strain, low - strain, and so on. furthermore, the result can only be gained under the complex analysis of the collected wave, and under the validation of the coring test

    目前，工程中常用的樁基檢測方法很多，但都存在著一些弊端：有的對樁破壞性嚴重，例如抽芯檢測；有的耗時、耗財、耗力，例如靜載荷試驗；還有的如低應變、高應變等檢測技術由於受到樁長、樁徑以及現場一些特殊情況的限制，操作很不方便，而且採集到的波形要經過比較復雜的處理分析方能得出結論，而這個結論卻還要輔助取芯手段加以驗證。
  12. Based on mono - pulse radar system and the analysis of terrain echoes, a geometrical model of air to ground ranging is constituted. by using the signals received from the sum and difference channels of terrain follow radar, a group of the expressions for terrain echoes are educed and characteristics of these echoes are obtained. according to the characteristics of the echoes, the theory and method of pass zero detection of difference channel and its applications are discussed in detail

    針對一維單脈沖雷達體制，分析了地形目標回波特性；建立了地形跟隨雷達空地測距的幾何關系；利用雷達收發信號，導出了地形跟隨雷達和差接收通道的回波信號表達式，進行了波形模擬，得到了地形跟隨雷達的地面散射產生回波在時域中的特性；根據和差回波特性，闡述了差信號過零點檢測測距的原理和方法及工程實踐中的應用，並給出了真實雷達對外輻射試驗的結果，驗證了文中的模擬。
  13. The new general signal source, represented by arbitrary wave generator, is widely used in the mordern testing field

    以任意波形發生器為代表的新型通用信號源，是現代測試領域內應用最為廣泛的通用儀器之一。
  14. This article in detail elaborates supply power and breakdown type and the test methed, how to scientifically grasp the different breakdown electric cable meter test profile analysis as well as the breakdown localization method, and introduces how to solve the problems appeared in the scene test

    摘要介紹了供用電企業中電纜的各種故障類型和故障測試方法，對不同故障電纜儀測試的波形進行了分析，闡述了電纜故障點的定位和現場測試中通過波形判斷故障的方法。
  15. Thirdly, in the environment of labview, several kinds of vis used for sensor signal test are designed, including wave generation, time domain measurement, filter disposal, frequency analysis, etc. after that, wavelet analysis in the application of one - dimensional signal de - noise is studied, threshold and translation invariance wavelet de - noise are realized, and wavelet de - noise vi for zero drift signal of the fiber optic gyro in fcs is designed using labview

    接著，在labview環境下開發了多種用於傳感器信號測試的虛擬儀器，具有波形發生、時域測量、濾波處理、頻譜分析等多種功能。隨后，研究了小波分析在一維信號消噪中的應用，實現了labview環境下的閾值法和平移不變量法小波消噪，並利用labview設計了飛控系統中光纖陀螺零漂信號的小波消噪儀。
  16. In this paper, the drive theory of the large ratio friction transmission is studied ; a new type elliptical cam wave generator is designed ; the large ratio friction transmission prototype is designed and manufactured ; based on the ansys finite element method software, structure of the elliptical cam is analyzed ; precision index of the manufactured large ratio friction transmission prototype, such as transmission accuracy, least step, stability of the least step, load capacity is measured by the absolute rotary encoder. by analyzing the measurement data and research content, it is think that the new elliptical cam wave generator could overcome a good many problems brought by processing errors, facilitate size precision adjustments, input moment can be achieved in the form of a pure force couple importing ; through this study, " the large ratio friction transmission prototype " could apply in practical engineering basically

    本文研究了大速比摩擦傳動的傳動理論;設計了新型橢圓凸輪波發生器，設計製作了大速比摩擦傳動樣機;用軟體ansys對所設計的橢圓凸輪結構進行了有限元分析;用19位絕對式編碼器測試了大速比摩擦傳動機構的傳動精度、最小步距、最小步距的穩定性以及帶負載能力等各項精度指標;對測量數據和研究內容進行了歸納和整理，認為新型橢圓凸輪波發生器克服了加工誤差帶來的諸多問題，新型橢圓凸輪波發生器可以進行尺寸精度調整，能夠達到輸入力矩以純力偶的形式輸入;通過本項研究，基本可以使「大速比摩擦傳動機構」在工程中得以應用。
  17. It can make the analysis report on the basis of the abstract nation standard. based practical analog analysis in some partial power net, obtain the harmonic oscillation characteristic curve, and verify the software is right

    通過對某局域電網的實例模擬分析，結果表明，獲得了諧波諧振特性曲線，還根據實際測試數據，恢復了電網實際電壓電流波形，驗證了軟體的正確性。
  18. At last we present the result and data in visualization, including main menu and online display window, initialization window, data processing record window, analog signal scale and result examining window, wave testing window etc

    包括主菜單及實時顯示窗口、初始數據輸入窗口、斷火次數顯示窗口、數據處理記錄窗口、模擬量的標定及查看標定結果窗口、波形測試窗口等。
  19. This paper designs a device of testing the arc shield voltage in the vacuum interrupter, and makes a study of the arcing and after - arcing recovery characteristics of the arc shield by measuring the arc current, the arc voltage, the recovery voltage and the arc shield voltage

    本文設計了真空滅弧室屏蔽罩電壓測量裝置，並對真空滅弧室在燃弧和弧后介質強度恢復過程兩個階段的電弧電流、電弧電壓、恢復電壓和屏蔽罩電壓進行了全面、系統的波形測試，研究了真空滅弧室蒸汽屏蔽罩在燃弧和弧后介質強度恢復過程的特性。
  20. Waveform measurement function

    波形測試功能
分享友人
分享到 Line

分享到臉書