注射模塑法 的英文怎麼說
中文拼音 [zhùshèmósùfǎ]
注射模塑法
英文
injection molding- 注 : Ⅰ動詞1 (灌入) pour; irrigate 2 (集中) concentrate on; fix on; focus on 3 (用文字來解釋字句)...
- 射 : Ⅰ動詞1 (用推力或彈力送出) shoot; fire 2 (液體受到壓力迅速擠出) discharge in a jet 3 (放出) ...
- 模 : 模名詞1. (模子) mould; pattern; matrix 2. (姓氏) a surname
- 塑 : 動詞(塑造) model; mould
- 法 : Ⅰ名詞1 (由國家制定或認可的行為規則的總稱) law 2 (方法; 方式) way; method; mode; means 3 (標...
- 注射 : injection; inject; get a shot
-
Plastics - injection moulding of test specimens of thermoplastic materials - small plates
塑料.熱塑性材料試樣的注射模塑法.小板Fibre - reinforced plastics - methods of producing test plates - injection moulding of bmc and other long - fibre moulding compounds - small plates
纖維增強塑料.試驗板的生產方法. bmc和其他長纖維化合物的注射模塑法.小型試驗板Fibre - reinforced plastics - methods of producing test plates - injection moulding of bmc and other long - fibre compounds - general principles and moulding of multipurpose test specimens
纖維增強塑料.試驗板的生產方法. bmc和其他長纖維化合物的注射模塑法.多用途試樣的一般原則和模製Fibre - reinforceds plastics - methods of producing test plates - part 10 : injection moulding of bmc and other long - fibre moulding compounds - general principles and moulding of multipurpose test specimens
纖維增強塑料.試驗板的生產方法.第10部分: bmc和其他長纖維化合物的注射模塑法.多用途試樣的一般原則和模製Plastics piping systems - injection - moulded socket fittings for solvent - cemented joints for pressure piping - test method for resistance to a short - term internal hydrostatic pressure
塑料管道系統.壓力管道溶劑膠粘接頭的注射模塑承口連接管件.短期內部液壓壓力的試驗方法Abstract : the molding method, process, and the equipment of thermoset runnerless injection molding have been discussed in this paper
文摘:論述了無流道熱固性塑料注射成型的方法、工藝、設備和模具設計方面的問題。3d modeling of plastic injection mould for box type parts
箱體類塑件注射模三維造型方法In order to help engineers solving the difficult problem of spatial layout in injection molding design, the adaptive and reconfigurable design methodology for injection molding was put for - ward, whose kernel was the mapping model of injection unit requirements to functional units to structural units based on constraints of reconfiguration
摘要針對復雜注塑模設計過程中的空間布局難題,提出了以重構約束的注塑成形單元需求功能元結構元映射模型為核心的注塑模適應性重構設計方法。This method requires two set of molds and two injection machines to use the stablise the pre - cast hard plastic materials inside the cavity of the second mold in the way of inserts. then, it reaches the effectiveness of multi - colour and multi - materials by injecting tpe on the hard plastic materials
此方法需利用兩套模具以及兩臺注塑機,將預制的硬膠件以鑲件形式固定於第二套模具的模腔內,再把tpe注射到硬膠件上,以達致多色多物料的效果。The methods and feasibilities by which the filling simulation software of plastic injection molding can be adjusted for mim have been discussed
探討了修改塑料注射成型充模流動模擬軟體作為金屬注射成形充模流動模擬的可能性及方法。Method of specifying thermoplastics injection mouldings - general requirements
熱塑性塑料注射模製品規定方法.第1部分:一般要求Method of specifying thermoplastics injection mouldings - additional requirements for polycarbonate, polyamide and polyethylene mouldings
熱塑性塑料注射模製品規定方法.第2部分:聚碳酸酯,聚酰胺和聚乙烯模製品的附加要求A new method for calculating the cavity dimensions of the injection mould for plastic gears, namely, modulus - varying method, was put forward. and two typical processing technologies were introduced
提出了一種計算塑料齒輪注射模型腔尺寸的新方法,即變模數法,並介紹了兩種典型的加工工藝。分享友人