泵壓過器 的英文怎麼說

中文拼音 [bèngyāguòqì]
泵壓過器 英文
pump filter
  • 泵 : 名詞（吸入和排出流體的機械） pump
  • 壓 : 壓構詞成分。
  • 過 : 過Ⅰ動詞[口語] （超越） go beyond the limit; undue; excessiveⅡ名詞（姓氏） a surname
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  1. Part of the electronic apparatus, medical equipment, spare part production and maintenance of the automobile, motorcycle, engine, aeroplane, metal press piese, oil, pump glib, compressor part and spinneret and washing, filtration of core of chemical fibre industry

    電子電器零件、醫療器械、汽車、摩托車、機車、飛機零部件的生產與維修，金屬沖壓件、油泵油嘴、壓縮機零件及化纖行業的噴絲板與過濾芯的清洗。
  2. Water wave pump combines the functions of air wave charger and water hammer pump to show fine performance, where the total energy of inflow is redistributed to heighten the presure of a part of the the flow to the desired level whereas for the rest of flow a low level of pressure is maintained, which causes moving water with high energy to reach to a higher place

    水波泵是一種巧妙地綜合氣波增壓器和水錘泵功能的全新的水泵，它通過合理利用水波動力的特殊性質，將來流中的總體能量進行重新分配，使一部分來流水提高到所需的高壓力，而其餘部分水則降到較低的壓力，即完成一個大多數能量向部分來流水轉移的過程。
  3. The pressure switch is suitable for almost all liquid and gaseous mediums and is used in vacuum technology pump control, refrigeration technology compressor control, gas technology stock monitoring, leakdetection, filter monitoring dirt detection, level measurement overfill protection, dry - running protection, aswell as a whole variety of measurement tasks in hydraulics and pneumatics, in machine, equipment and plantconstruction, in process technology and in building technology

    壓力開關幾乎適用於所有液體和氣體介質，可以用於真空技術氣泵控制製冷技術壓縮機控制氣體技術貯存量監測泄露探測過濾監測灰塵探測，液位測量過量保護空運行保護，也用於過程技術和建造技術的機器機械和設備製造中的所有液壓和氣壓測量任務。
  4. The system follows carnot cycle principle. driven by electricity, its working substance absorbs the latent heat in the air or other low - temperature heat source, and waste heat let out of living or industry, compresses it to heat by compressor, exchange, exchange heat with water to higher the water temperature ( 55 warm ). it a new water heating apparatus, used in home heating, and influenced by environment runoff and the heat exchang of working substance. this system is more used in southem china

    根據逆卡諾循環原理，採用電能驅動，通過工質吸收空氣中或其他低溫熱源中無法被利用的太陽能潛熱、生活及工業排放的廢熱，通過壓縮機壓縮升溫，再與水換熱，使水溫升高，獲得（ 55 ）熱水，是一種新型的熱水製造設備，應用於家庭和熱水系統，受到環境溫差和工質換熱的影響，熱泵熱水器/熱水系統更多適合南方地區應用。
  5. The air thermal cnergy water heater creates the new generation hot water cquipments. it makes use of the negative card promise successfully, drieing a hot pump with the elcctrie power. equiping through a hot pump medium of compesing parts evaporate a machine. hot pump, congealed machine and inflate valve, urge the work quality completes evaporationt absorb calories within air continuously compress compress congealed reduce expenses evaporate of the thermody name energy cirenlation proess, transfer the calories in the environment to the water thus in, transfer the in great quantities free calories in the air to the life to use a water in

    空氣節能熱水器是創新一代熱水設備，它成功地運用逆卡諾原理，用電能驅動熱泵，通過熱泵裝置中的構成部件-蒸發器，熱泵，冷凝器和膨脹閥，促使工質不斷完成蒸發（吸收空氣中的熱量）壓縮冷凝節流蒸發的熱力循環過程，從而環境的熱量轉移到水中，將空氣中大量免費的熱量轉移到生活中水中
  6. ( 5 ) taking full of advantage of the ado. net and asp. net technology under the. net platform. it construct a powerful remote control and monitor system and meet the reqirment of the users. in order to achieve real - time control, it design a front environments built on the asp. net structure, from which the system can fulfill the real - time function. due to the characteristic of drain off water pump station remote control and monitor system ( big pump station need high voltage ( 6000v ) and great power ), so now do n ' t adopt the ways that client _ end controls it. in addition, the server - end design a database to manage from which the system could tackle users information and online users log in the form of winform and strengthen the safety of the system

    Net平臺下的ado . net與asp . net技術，發揮兩者的武漢理工大學碩士學位論文優勢，構造了功能更強的遠程監控系統，更好的滿足用戶的需要。系統設計中以asp . net架構為前臺環境，實現了客戶端通過ie瀏覽器來實時的監控到排水泵站的運行情況，使系統達到了實時監視，但由於大泵機工作電壓高（ 6000v ）功率大（ 100okw ）的特點，暫不採用客戶端控制系統。在服務端，設計了數據庫，並且以winform的形式來管理網路管理員和用戶的信息以及在線用戶的日誌，加強了系統的安全性。
  7. To tune up the frequency of power supply by the transducer in the system, this adjusting make the speed of electromotor and performance curve of pump change. at last, it make the status of a pump alter

    在變頻調速恆壓供水系統中，單臺水泵工況的調節是通過變頻器來改變電源的頻率f來改變電機的轉速n ，從而改變水泵性能曲線得以實現的。
  8. After the coke being puted into the coke - quenching device, the lid of the device should be shut at once. while the suction pump, refrigeration compressor, high pressured water circuling pump are started, the subpressure will be produced by the burning coke. then, in the vacuum, the coke will be extinguished in a flash. the burning of the coke instantly, still, produces a large quantity of heat which can be taken away by circulating water in refriger and the interlayer, after that, the temperature will fall to 60oc, even lower. in this condition, the coke will be pushed out to be stored, thus, the coke won ' t rekindle

    當焦炭推上攔焦車進入熄焦器后，立即關閉罐蓋，同時啟動真空泵、冷凍機、高壓循環水泵，這時，燃燒著的焦炭就會因真空泵把熄焦器內抽成負壓，由於缺氧，使焦炭熄滅，雖然煤炭在瞬間被熄滅，但由於焦炭生成過程中所產生的大量的熱量還存在，這時，冷凍機和夾層中的循環水的工作就會把焦炭中的熱量帶走，使之在短時間內將溫度降到60以下，在這種狀態下把焦炭從熄焦器內推出入庫，焦炭就不會復燃。
  9. A test - bed of dg45 - 80 10 hypo - pressure feed water pump is designed, based on which the general on - line performance testing system is developed and the thermodynamic method is introduced to measure the efficiency of the pump. a new programming technology combining vc + + with matlab is presented by which the vibration monitoring system of boiler feed water pump is developed successfully to perform data analysis after on - line acquisition

    本文首先進行了次高壓鍋爐給水泵dg45 80 10實驗臺的設計，在此實驗臺設計成功並安裝調試通過的基礎上，開發了鍋爐給水泵通用性能試驗系統，包括測點的布置、各型測量儀器的選購，設計，安裝和調試以及軟體平臺開發。
  10. In the third chapter, the mathematical models of project system have been established, and simulation has been done on the simulink enviroment of matlab software kits. the simulation focus on the effects of main parameters on the dynamic characteristics of speed control system, and the main parameters include viscosity damp coefficient and friction torque of electrical motor shaft, internal leakage coefficient of pump / motor of hydraulic circuits, gas volume of pressure accumulator, viscosity damp coefficient of cylinder piston and different running building floors, etc. at last, theoretical research effects of the flow and pressure pulsation of pump / motor on car speed and oil volume leakage theory are discussed. the fourth chapter of this thesis concerns the research on the key items about hydraulic power control system according to the ens 1 - 2 and other hydraulic elevator standards

    論文第三章針對組成系統的各個模塊進行了機理建模，並且通過matlab軟體中的simulink圖形化模擬環境進行了本課題系統的模擬研究，主要針對影響系統特性的主要參數變化，動態分析系統的輸出特性，在上下行工況中，分析了電機軸系粘性阻尼系數、軸系摩擦力矩、主迴路蓄能器迴路液壓泵馬達內泄漏系數、蓄能器氣體容積、液壓缸柱塞粘性阻尼摩擦系數以及不同運行樓層工況等參數對系統特性的影響；最後對軸向柱塞泵馬達的流量壓力脈動對電梯轎廂速度的影響和蓄能器內油液體積損失機理進行了理論研究。
  11. Its main products include : hydraulic pumps, motors, valves, tanks, electronic products, complete sets of filters and systems

    其主要產品包括：液壓泵馬達閥油缸電子產品過濾器以及成套系統。
  12. Based on examples, the problems in reinstallation process of oil pump, tap - changer and bushing after transformer maintenance overhaul are analyzed. the measures to prevent the problems are presented

    摘要以實例分析了變壓器大修后潛油泵、無勵磁分接開關、套管回裝過程中存在的問題，提出了防止類似問題發生的措施。
  13. The suitable oil flux during the circulating of transformer could be defined according to the difference of temperature between the oil and wind in the inlet and the cooling capacity of the wind cooling system ; besides the oil flux can be determined by ultrasonic, it can be estimated whether the oil is flowing equably by determining the oil flux in the branch pipes ; reducing the oil flux of the oil pump could be realized by controlling to change its frequency, which could not only save the energy, reduce the wastage, but benefit the transformer ' s circulating safely

    變壓器運行中可根據進口油溫和進口風溫之差、風冷卻器的冷卻容量來確定合適的油流量；油流量可以通過超聲波法進行測量，測量油的分管流量還可判斷油流的均勻情況；降低潛油泵流量可通過潛油泵的變頻控制來實現，不僅節能降耗，對變壓器的安全運行也有著重要意義。
  14. Objectives : to make up an irrigating machine for firearm wound so as to improve the successful rate of immediate treatment and reduce the infection rate of firearm wound. methods : the machine is made of pump, pressure adjuster, heater, nozzle, shield, and so on

    方法：與華南理工大學合作，用由不銹鋼或無毒塑料製成的水泵、壓力調節器、加熱器（ ht ） 、噴槍、防護罩等配件，製作一臺火器傷清創沖洗機，並通過動物實驗檢測其效能。
  15. The body of filter adopts anti - block unidirection press valve, avoiding from the pump ' s breakdown when the pipe and papercore is stuffed, from the idle running and damage on motor

    過濾器本體採用防堵單向壓力式閥門，避免了管道，紙芯堵塞后悶泵現象，有效防止水泵空轉，損壞電機。
  16. Secondly, based on the account of hydraulic dynamic factor ( hydro - capacitance and hydro - inductance ) and the analysis of each component ' s math model, the system ' s math models of three situations are established

    其次，在充分考慮液壓系統的動態因素（液容和液感） ，並對各液壓元器件建模分析的基礎上，分別建立了速閉閘液壓控制系統在泵或蓄能器作用下開啟、關閉閘門過程的數學模型。
  17. At the same time, experiment data of the prototype are compared with those of the conventional system and the flash - tank throttle system to test the correctness of the theory. at last, exergy of the quasi two - stage compression heat pump system coupled with ejector is analysed, such as exergy loss, exergy efficiency and exergy loss distributing, and compared with those of the flash - tank throttle system

    通過實驗數據來分析該系統的性能，驗證和修正理論分析的方法與結果，並與相同工況下單級系統及閃發器節流系統的實驗數據進行比較，從而得出準二級壓縮?噴射復合熱泵系統低溫適應的優越性，驗證了理論分析的正確性。
  18. Sg140 type truck is equipped with advanced high / low pressure pump and flexible windlass. high pressure water vapour through multifunction gun can kill the fire of appliance equipment

    Sg140型裝配技術先進的高低壓泵和靈活的機動卷盤，通過多功能槍的高壓霧化水還具有撲滅電器設備火災的功能。
  19. By using the hydraulic torque converter to drive the mud pump, both the prime motor and the working machine can be protected, and the pump pressure can be controlled in the whole course of drilling if the rated rotary speed of the diesel engines is kept

    通過液力變矩器驅動鉆井泵可同時保護原動機和工作機；在保持柴油機額定轉速的條件下，可實現泵壓的全過程式控制制。
  20. 3. through experiment using sensor and technique of dynamic measurement, the data of the pump pressure, pressure of upper and nether cavity of hydraulic vat and punching power has obtained synchronously. then exact figure and corresponding relation of these parameter also some relationship between these parameter is got by means of technology of signal processing during elevating, falling and pressure - retaining. 4

    在液壓打樁錘實驗裝置上利用傳感器和動態測試技術得到油泵出口壓力、液壓缸上、下腔壓力和樁錘下打力的同步實測數據，再利用信號處理技術分析上述參數在上升、下打和保壓過程的精確值及對應關系，獲取了液壓系統動力學參數與打樁錘力學特性關系的設計知識。
分享友人
分享到 Line

分享到臉書