泵小齒輪 的英文怎麼說

中文拼音 [bèngxiǎochǐlún]
泵小齒輪 英文
pump pinion
  • 泵 : 名詞（吸入和排出流體的機械） pump
  • 小 : Ⅰ形容詞1 （體積、面積、數量、強度等不大） small; little; petty; minor 2 （年紀小的; 年幼的） youn...
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 齒輪 : gear [rack; toothed] wheel; （toothed） gear; wheel gear
  1. If the coefficient of engagement overlap decreases, the flow aggrandize, trapping volume and the flow pulsating ratio decreases

    隨著齒輪嚙合重合系數的減小，齒輪泵的流量增大，困油容積和流量脈動率減小。
  2. An optimization example showed that the method was valid and satisfied the design requirement of some related structure and performance parameters on the conditions of minimum volume, concordant gears and rotors cavity structure

    實例分析證明，該方法可以在保證泵體積小、齒輪腔與轉子腔結構協調的情況下，滿足有關結構和性能參數的設計要求。
  3. The following is the detail design of the pump, and a optimum mathematical model are presented to mostly reduce the helical gear pump flow pulse

    在此基礎上進行了斜齒齒輪泵的結構設計，通過建立斜齒齒輪泵齒輪的優化數學模型，優化計算出使輸出流量脈動最小的斜齒輪參數，製造出斜齒齒輪泵樣機。
  4. The researchful results indicate that the flux pulse ration of ordinary helical gear pump without clearance is less than that of the gear pump with clearence under the condition that the main parameters are same, and the flux pulse ration of ordinary helical gear pump is less than that of whole profile meshing helical gear pump

    研究結果表明：在主要參數相同的情況下，普通斜齒齒輪泵無側隙時流量脈動率小於有側隙時的流量脈動率；全齒廓嚙合斜齒輪泵比普通斜齒輪泵的流量脈動略小。
  5. 4. based on the viscous hydrodynamics, the leakage characteristics of newton liquid that is transmitted by helical gear pump are researched for the aim of the least power loss, and the leakage model is founded, the mathematic models of the radial and the axial leakage are gained. at the same time the optimal radial leakage and axial leakage are got, and the numerical calculation is achieved

    基於粘性流體力學，以功率損失最小為目標，首次對牛頓流體在斜齒齒輪泵中的漏流特性進行了研究，建立了泄漏模型，分別得到了斜齒齒輪泵的徑向和軸向泄漏的數學計算模型；同時得到了斜齒齒輪泵最佳徑向間隙和最佳軸向間隙，並在此基礎上進行了數值計算。
  6. It also indicates that this kind of gear pump can be made domestically ; accordingly cost will be greatly reduced for domestic users. the market for this product is promising in china

    對于國內即將投資興建的新的聚酯生產裝置，該齒輪泵可以替代進口產品，除可以降低投入成本外，還可以減小各種維護方面的費用。
  7. Although the flux per revolution of the optimized pumps is a little smaller than that of tatsuno combined pumps, other characteristics, such as fluctuation rate, maximum pressure angle and velocity fluctuation rate etc, are much better. the methods to cut gears are proposed in the theory for the practical produce in the future

    雖然，在體積相等的條件下，優化出來的外圓弧包絡線內嚙合齒輪泵的排量略小於tatsuno組合泵的排量，但其它性能（如：流量脈動率、最大壓力角、速度波動量）都更優。
  8. Taking a rotor shape parameter as a variable, the minimum volumes of rotor cavity and pump flow as the design objectives, as well as some constraints on rotors and gears cavity structures, an optimization design model of un - contact rotor pump was constructed

    摘要以轉子形狀參數為變量，以流量和轉子腔體積最小為設計目標，考慮齒輪腔和轉子腔結構的有關約束，建立了非接觸式轉子泵的優化設計模型，給出了優化設計步驟。
  9. At last considering the flow pulsation as objective function, optimization of the parameters of the gear using ga method is brought forward and an optimum model is presented to achieve the optimal parameters of the gear that make the flow pulsation lowest

    最後以流量脈動為目標函數，採用遺傳演算法對齒輪泵結構參數進行了優化設計，建立了齒輪泵參數優化數學模型，給出了使輸出流量脈動最小的齒輪泵最優參數。
  10. As external gear pump has the most serious problem of flow pulsation, how to analyze the flow pulsation of gear pump and to optimize the construction parameters of gear pump is especially important for the design and performance improvement of gear pump

    在液壓泵中，以外嚙合齒輪泵的流量脈動最大，因此對齒輪泵流量脈動進行分析，以減小流量脈動為目標，對齒輪泵的結構參數進行優化設計，從而為齒輪泵的設計及齒輪泵性能的提高提供理論基礎。
分享友人
分享到 Line

分享到臉書