泵弧 的英文怎麼說

中文拼音 [bènghú]
泵弧 英文
mercury arc
  • 泵 : 名詞（吸入和排出流體的機械） pump
  • 弧 : 名詞1. [數學] （圓周的任意一段） arc2. （古代指弓） bow
  1. The sources of these internal transients are everyday items, such as air compressors, arc welders, pumps, elevators, switching power supplies and other inductive loads

    這些內部電涌的根源是每天都會使用的設備，如空氣壓縮機，電弧焊接機，泵，電梯，開關電源和其他的感應負載。
  2. Mjc : the sources of these internal transients are everyday items, such as air compressors, arc welders, pumps, elevators, switching power supplies and other inductive loads

    這些內部電涌的根源是每天都會使用的設備，如空氣壓縮機，電弧焊接機，泵，電梯，開關電源和其他的感應負載。
  3. To overcome the disadvantage of tatsuno combined pumps and to improve the characteristics of the pumps, a new kind of pump with the fixed transmission ratio is proposed, the teeth of which are circle - arc and its envelope

    針對tatsuno雙圓弧組合泵存在的不足，提出了該泵中的一對齒輪副採用定傳動比的圓弧及其包絡線齒輪副的方案，以改善泵的性能。
  4. The tooth shape of gear pump has important influence on machining and characteristics of pumps, such as flow rate, fluctuation rate and noise etc. first, the working principle of tatsuno combined pumps is analyzed in this article

    齒輪泵的齒形對泵的加工、性能（如：流量、脈動率、噪聲）等有很大的影響。本文首先分析了進口tatsuno組合泵的工作原理，並進一步分析了其採用一對雙圓弧齒輪的優缺點。
  5. Although the flux per revolution of the optimized pumps is a little smaller than that of tatsuno combined pumps, other characteristics, such as fluctuation rate, maximum pressure angle and velocity fluctuation rate etc, are much better. the methods to cut gears are proposed in the theory for the practical produce in the future

    雖然，在體積相等的條件下，優化出來的外圓弧包絡線內嚙合齒輪泵的排量略小於tatsuno組合泵的排量，但其它性能（如：流量脈動率、最大壓力角、速度波動量）都更優。
  6. After thoroughly analyzing the influence of each pump parameters on the gear pump performance, the paper developes the criterion for optimum gear parameters, which can be utilizied in practice easily for gear manufacturing using normal involute gear hob with two - fillet type. the conclutions studied by the paper are : 1. both the addendum coefficient and the deddendum coefficient of the pump gear should be 1. 125

    以目前國內普遍使用的雙圓弧頭全齒高為2 . 5倍模數漸開線標準滾刀作為泵齒輪的加工刀具，通過對齒輪加工原理的分析，提出了欲使泵齒輪參數達到最佳，泵齒輪的齒頂高系數和齒根高系數都為1 . 125 ；對變位系數的確定應考慮到泵齒輪的根切、齒頂厚、重合度以及側隙因素；泵齒輪為避免過渡曲線干涉，必然要存在根切現象。
  7. In the first part, the method of velocity coefficient was used to design a 100mm diameter impeller with five single - arc - cylinder blades, and the method of velocity moment was applied to design the volute " s cross - section. the volute " s cross - section is a rectangle, which was designed as a whole structure with the front shroud of the pump. a special lighting window was designed on the side

    在第一部分工作中，設計了一個帶半開式葉輪的微型泵：葉輪外徑100mm 、共5片單圓弧圓柱形葉片；蝸殼採用速度矩法設計，內為矩形斷面，和泵殼前蓋板為一整體、透明結構，側面專門設計一個打光窗口。
  8. Gear form is precisely, plotted by portray point. for friendly user interface, the dialog - box is given, using dcl language to compile dialog box program. because the given program can not only output all the optimum basic parameters of pump gear, but also simulate the meshing process of a pair of pump gears, gear pump can be designed and manufactured economically

    精確繪出泵齒輪的輪齒幾何形狀，尤其精確繪制出了標準齒輪滾刀切出的齒根過渡曲線，演示了國標雙圓弧頭標準滾刀加工泵齒輪的過程，並實現了泵齒輪副的嚙合模擬，這些對檢查輪齒干涉以及確定齒輪泵的卸荷槽位置和形狀提供了依據。
  9. The parameters of inner meshed gear pump with external circle - arc and its envelope teeth are optimized by the method of the genetics algorithms

    利用遺傳演算法對外圓弧及其包絡線內嚙合齒輪泵的參數進行優化。
分享友人
分享到 Line

分享到臉書