活塞組件 的英文怎麼說

中文拼音 [huósèzǔjiàn]
活塞組件 英文
piston assembly
  • 活 : Ⅰ動詞1 （生存; 有生命） live 2 [書面語]（救活） save （the life of a person）:活人無算 （of a goo...
  • 組 : Ⅰ名詞1 （由不多的人員組成的單位） group 2 （姓氏） a surname Ⅱ動詞（組織） organize; form Ⅲ量詞（...
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  • 活塞 : plunger; stop; bibb cock; bib（b）; [機械工程] piston; gas piston; headed piston活塞桿 piston rod...
  • 組件 : assembler
  1. Based on the hydromechanics principle, the hydraulic equipment can push compressive oil into actuators by the pressure and direction control circuits. the piston of actuator translates distributed pressure into centralized force of piston rod

    液壓加載根據液壓流體力學原理，利用液壓元件組成的壓力和方向控制迴路，將一定壓力的油液輸入液壓缸，由液壓缸內的活塞把分佈的油壓轉變為集中力，最後經活塞桿輸出。
  2. Barrel buffer piston rod assembly

    槍管緩沖器活塞桿組件
  3. Methods the heat stroke model was established under circum stances of dry buld temperature ( 34. 5 0. 5 ) and ( 60 5 ) % relative humidity. 40 mice were randomly divided into five groups including reduping group, xihuangqijiao group, dexamethasone group, heat strike group and normal group and the increased rate of temperature, subsistence time and the number of diarrhea of experimental animals were observed

    方法在干球溫度（ 34 . 5 0 . 5 ） ，相對濕度（ 60 5 ） %的條件下建立小鼠中暑模型，將40隻小鼠隨機分為熱毒平組、西黃芪膠組、高溫中暑組、地塞米松組和正常對照組，觀察動物的肛溫上升速率、存活日寸間和致瀉作用。
  4. Heat transfer boundary condition and thermal load of combined - piston for locomotive diesel engines

    機車柴油機組合活塞的換熱邊界條件及熱負荷
  5. Piston is the key parts of engine of tank and chariot, whose shape is convex and variable ellipse. the piston was made up of separate parts. the different part used different material

    活塞是坦克、戰車等發動機的關鍵件，其形狀是個「中凸變橢圓」的異形回轉體，是由2 3種不同材料加工的分體零件組合而成的，而且在機械切削加工完成之後又在外表面噴塗了一層石墨。
  6. Reciprocating displacement pumps and pump units ; requirements and testing

    往復式活塞泵和泵組件.第1部分:要求與試驗
  7. To solve the heat transfer boundary problem among the piston, liner, coolant and body parts, especially the temperature and heat transfer among the coolant, liner and body

    摘要為解決發動機活塞組缸套冷卻水機體之間傳熱邊界條件難以確定的問題，尤其是冷卻水和缸套、機體之間的流固邊界的溫度和換熱系數，將這幾個部件作為一個耦合系統進行傳熱研究。
  8. Detailed discussion on fea methods used in the coupling model of ic engine piston assembly and cylinder with the combination of the theoretic of fea, and theoretical foundation for two - and three - dimensional fea analysis of holistic coupling system of combustion chamber components

    結合有限元理論知識，詳細論述了在內燃機活塞組與缸套耦合模型中會用到的有限元方法。並為燃燒室部件整體耦合系統的二維、三維溫度場有限元分析奠定了理論基礎。
  9. In the paper, in accordance with the thermal power torpedo propulsion system using hap tri - component fuel, with the i - deas software, applying the cad technology and the fem, the research of simulation on the piston - one of key parts of engine was proceeded and the paper presented the whole analysis process of the piston including thermal analysis. in the paper, the question of the boundary condition in the complicated engineering was explored and the temperature field. the stress field and the deformation of the piston were computed and analyzed under a new kind of fuel ( hap )

    本文針對三組元魚雷熱動力系統，應用i - deas軟體，利用cad技術和三維有限元方法（ fem ） ，對發動機的關鍵零件? ?活塞展開模擬研究，對活塞進行了包括熱分析在內的全過程的模擬計算，探索了復雜工程中邊界條件的處理問題，分析計算了魚雷發動機活塞在新型燃料（三組元燃料）工作下的穩態溫度場、應力場與變形情況，最後，根據分析結果對其結構提出了改進意見。
  10. 1the connecting lever is employd trundleing the needle with maintains a module chiefly to be used the motor. the compressor is with else crank connecting instrument, oad and the composition mould style fixs the necessary demand on the basis of the motorcycle in home and abroad, consider to exchange and the current demand, fix that the crank annuls that the use trundles the needle with maintains module kzk and a piston to annul in the way of kbk mould

    1連桿用滾針和保持架組件主要用於發動機，壓縮機和其它曲柄連桿機構上，外形尺寸和結構型式的確定根據國內外摩托車的配套要求，考慮到互換和通用的要求，確定了曲柄銷用滾針和保持架組件kzk和活塞銷用kbk型。
分享友人
分享到 Line

分享到臉書