活塞連桿 的英文怎麼說

中文拼音 [huósèliángǎn]
活塞連桿 英文
piston rod
  • 活 : Ⅰ動詞1 （生存; 有生命） live 2 [書面語]（救活） save （the life of a person）:活人無算 （of a goo...
  • 連 : Ⅰ動詞1 （連接） link; join; connect 2 （連累） involve （in trouble）; implicate 3 [方言] （縫） ...
  • 桿 : 桿名詞（桿子） pole; staff
  • 活塞 : plunger; stop; bibb cock; bib（b）; [機械工程] piston; gas piston; headed piston活塞桿 piston rod...
  • 連桿 : [機械工程] link; connecting rod; perch; go between; column; connecting bar; crank guide; link lev...
  1. One machinery makes wen zhoudong limited company is to be engaged in research, development, production, sale is domestic and international the gas a powerful person of all sorts of medium compressor, a powerful person piece, lever of annulus of bedspring, piston, piston, piston, sealing ring, crosshead, crosshead is sold, copper is covered, bolt of connecting rod, connecting rod,

    溫州東一機械製造有限公司是從事研究、開發、生產、銷售國內外各種介質壓縮機的氣閥、閥片、彈簧、活塞、活塞環、活塞桿、密封圈、十字頭、十字頭銷、銅套、連桿、連桿螺栓、軸瓦、曲軸、缸體及缸蓋、缸套、凈化設備及部件、冷卻器等壓縮機配件的專業技術型企業。
  2. In the simulation, the mpc technique of msc. nastran is used to simulate the mechanical behavior of contact between the interfaces of piston pin and bearing of small end, crankpin and big end bearing, connecting rod body and bearing cap ; also constraints are applied to the connecting rod reasonably

    分析中採用了patran中的多點約束（ mpc ）技術，有效地模擬了活塞銷與小頭孔內表面、曲柄銷與大頭孔內表面以及連桿體與大頭蓋接觸面的力學接觸狀態，並對連桿進行合理的約束。
  3. It is applied to sorts of locomotive engine, in course of revolving of crank and connecting rod mechanism, there are revolving of the crankshaft, swinging of the connecting rod and reciprocating motion, so its motion state is complex, and periodic unbalanced force, by a few components, is great

    曲柄連桿機構在高速運轉過程中，有曲軸的轉動、連桿的擺動及活塞的往復運動，其運動狀態復雜，各個部件所產生的周期性不平衡慣性力大，是引起發動機振動的主要原因。
  4. The connecting rod is attached to the piston by the piston pin.

    連桿與活塞的連接是採用活塞銷。
  5. As the piston descended, a ratchet engaged the piston rod and engine shaft and thus power was transmitted.

    當活塞下行時，棘輪連接活塞桿和發動機軸，因此將功率輸送出去。
  6. The piston end of the rod is attached to the piston by the piston pin, or wrist pin.

    連桿的活塞端用活塞銷或銷軸安裝在活塞上。
  7. There is no clutch, gearing, oil changes, smog check, pistons, rings, valves, crankshaft, flywheel, rods, wrist pins, etc., etc

    沒有離合器，傳動裝置，機油變化，尾氣檢查，活塞，活塞環，閥門，曲軸，飛輪，連桿，肘節銷，等等。
  8. The reassigned smoothed pseudo wigner - ville distribution ( rspwvd ) is introduced, which has less interference and higher resolution than other time frequency distributions like wigner - ville, choi - williams etc. it is used to detect the multi - knocking of engine such as cylinder, piston pin, valve, crank bearing, connecting rod bearing and jib knocking. a new fault diagnosis technique based on the rspwvd for the engine multi - knocking problem is proposed. by comparing the bispectrum and bicoherence of the gear vibration signals, it is demonstrated that bispectrum has an advantage over bicoherence for feature extraction of such signals

    第四章首次引入一種重分配方法，得到干擾項少而解析度高的重分配平滑偽魏格納維爾分佈（ rspwvd ） ；對發動機曲軸主軸承響、連桿軸承響、活塞銷響、活塞敲缸響、氣門響和挺桿響等常見機械異響故障振動信號特徵進行了全面地比較分析；通過對各種異響故障特徵信號的分析研究，提出基於rspwvd的發動機多異響故障診斷策略，利用該策略可以準確識別不同的發動機異響故障。
  9. The piston pin joins the piston to the connecting rod

    活塞銷把活塞和連桿連接起來。
  10. Piston and connecting rods are crack tested in accordance with test equipment instructions

    根據監測設備要求對活塞與連桿作裂縫檢測。
  11. The reconditioned piston and rod assembly is lubricated protected against damage and foreign matter and lapelled to ensure identification

    翻新的活塞與連桿總體已經潤滑以防止損壞或異常情況發生。
  12. Calculates the piston displacement, speed, acceleration, and analyzes the forces burden of the piston - joint - shank - framework

    2 、計算了活塞位移、速度、加速度，分析了活塞連桿機構的受力。
  13. More often than not the combustion noise refers to the noise radiated from the cylinder cap, piston, rod, crankshaft to the engine body propelled by the pressure vibration generated out of the combustion inside the cylinder

    燃燒噪聲和機械噪聲很難嚴格區分，通常將由於氣缸內燃燒所形成的壓力振動通過缸蓋、活塞-連桿-曲軸-機體向外輻射的噪聲稱之為燃燒噪聲。
  14. 4 ) have studied the natural vibration characteristic of the piston - connecting rod - crankshaft while keeping in touch with the condition each other adopting systematic methods.,

    4 ）採用系統的方法研究了活塞-連桿-曲軸三者在相互接觸條件時，在不同轉角下的固有振動特性。
  15. This thesis, on the basis of modern theories of vibration, ked analysis and finite element method, sets up a kinetic model of piston - linkage mechanism of diesel engine, by i - deas software of sdrc usa, which involves the effect of joint clearance in mechanism. by the presumption of " transient structure " in ked analysis, the mechanism " s dynamic responses in every transient structure conditions are calculated, and it provides a reliable theory basis for the optimization design of diesel engine

    本課題基於現代機械彈性動力學理論以及有限元分析方法，利用美國sdrc公司的- deas軟體，對含運動副間隙的柴油機的活塞、連桿機構建立了動力學模型；運用ked分析中的「瞬時結構」假定，計算出了機構在各瞬時結構條件下的動態響應，從而為柴油機優化設計提供了可靠的理論依據。
  16. Piston and rod assembly

    活塞連桿總成
  17. An inspection is completed on pistons and connecting rods and a report on the feasibility of repair is given to the supervisor

    活塞連桿曲軸的檢驗報告已經出據，並維修的可行性報告已交付給相關的監督人員。
  18. Piston - linkage mechanism, as the mechanism to transfer the power of engine, bearing the heavy gas - explosive force, inertial force etc, is easy to arise vibration and noise. besides, the joint clearance in mechanism could also irritate the vibration and worsen the dynamic properties of mechanism

    作為內燃機動力傳遞機構的活塞連桿機構，由於在周期性的工作循環中，承受著強大的氣體作用力，往復慣性力、離心慣性力等的沖擊，極易引起振動和噪音；同時由於運動副間隙的存在加大了振動的影響，惡化了機構的動態性能。
  19. Complex displacement simulation of piston - linkage mechanism of diesel engine

    活塞連桿機構的復合變形模擬
  20. The main research is as follows : analyze and research the characteristic of the crank - connect rod mechanism of the single - cylinder internal - combustion engine, the mathematical model of three - mass point has been established and the program of its inertia force and moment has been designed

    研究工作主要包括以下內容:針對單缸內燃機活塞-連桿-曲柄機構的特點，運用運動學和動力學理論對其進行分析，建立了單缸內燃機的兩質點和三質點模型，推導出單缸內燃機不平衡慣性力和慣性力矩的數學模型。
分享友人
分享到 Line

分享到臉書