流速噴嘴 的英文怎麼說

中文拼音 [liúsùpēnzuǐ]
流速噴嘴 英文
flow nozzle
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  • 流速 : [機械工程] velocity of flow; strength; [水文] current velocity; current speed; flow rate流速管 pi...
  1. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  2. The effect of the height between nozzles and ground plate, the distance between the nozzles, the inlet velocity of the nozzles, and the velocity of the cross flow on the flowfield structure were studied one by one

    分別就噴嘴距地面高度、噴嘴間距、噴嘴出口速度、橫向流等，對噴射垂直撞擊平板流場的影響，逐一討論。
  3. According to rigorous procedures, an experimental study was carried out to investigate the effects of jet exit velocity, flow direction, fluid subcooling and nozzle diameter on hysteresis of boiling heat transfer with impinging circular submerged jets of highly - wetting liquids

    摘要系統地研究了液體在圓形斷面噴嘴浸沒射流作用下沸騰熱滯后與射流沖擊速度大小、液體流動方向、液體過冷度和噴嘴直徑等因素的影響。
  4. With gelatin liquor as adhesive and wheat meal as granulation material, the effects on spray granule ' s strength of fluidizing gas velocity, bed temperature, nozzle air pressure and adhesive concentration were studied experimentally in a batch conical fluidized bed spray particle generator

    本文在一間歇錐形流化床噴霧造粒器中，以食用小麥澱粉為原料，以明膠的水溶液為粘結劑，實驗研究了流化氣速、床層溫度、噴嘴霧化空氣壓力、粘結劑濃度對噴霧造粒顆粒強度的影響。
  5. Focusing on the performance evaluating and the design of tripropellant injector, adopting the cold test rig with background pressure supply, malvem particle analyzer, ccd photography system, tripropellant hot test - bed, numerical simulation software and auxiliary theoretical a nalysis, the d ischarge c haracteristic a s w ell a s a tomization p erformance o f the injector and the combustion performance as well as the mode - transition characteristic of thrust chamber are studied detailedly based on the 3 different structures of coaxial tripropellant injector, large numbers of important conclusions are gained

    本文圍繞三組元噴嘴的性能評定及設計方法。採用反壓冷試臺、馬爾文測粒儀、 ccd高速攝影系統、三組元發動機熱態試驗臺、數值模擬程序及輔助理論分析等多種技術手段和研究方法，對三種結構的同軸式三組元噴嘴深入進行了噴嘴流量特性和霧化特性、推力室燃燒性能和轉工況性能研究，得到了大量重要結果。
  6. Based on the analysis of regime of spray and heat transfer, the spray nozzles were redesigned to distribute liquid in the center area of th e tower and the gas inlet was enlarged to raise gas velocity

    根據對順流式空塔的噴淋及傳熱模式的分析，重新設計了噴嘴，使噴淋液在設備中心附近集中；縮小了進氣管直徑，以提高進口氣體的流速。
  7. Material is ejected into the crushing chamber by means of high speed ejection flow formed by high - pressure air through charging ejector, and the crushing nozzles outside ejects high - speed airflow into the crushing chamber at certain direction, making the materials severely collided and fractionated, and thus crushed

    該機是靠高壓氣體通過加料噴射器所形成的高速射流，使粉碎原料被射入料碎室，粉碎室外圍的粉碎噴嘴，有方向性的向粉碎室噴射高速氣流，使物料間產生激烈的碰撞，磨擦而獲得粉碎。
  8. It came true to take advantage of transfer standard to compare and analyze the naturalgas standards of measurement on site. the dissertation used the transfer standards to take the site comparative experiments to the sonic nozzle standard measurement of the nation crude oil great flux measure station carried by vehicle and the standard measurement of the general pertrifaction plant. it evaluated and analyzed the measure capability of these two standards, thus to keep them fulfilling the rules of the verification and the regulations of relative criterions

    本文通過使用傳遞標準，對國家原油大流量計量站車裝音速噴嘴標準裝置和大慶石化總廠計量站氣體計量標準裝置進行現場比對試驗，對這兩項天然氣計量傳遞標準裝置的計量性能進行了評價和分析，使國家站和大慶石化的天然氣流量計量標準裝置達到了檢定規程和相關標準的規定要求。
  9. Great difference in pressure for two flow made pressure wave system and it help to extend the delay time for gas in chamber, which increases combustion effusion. second, to increase combustion effusion, the inlet temperature of air and gas should be enhanced in the range of heat releasing in chemical reaction. third, the first work condition is unburned absolutely and the second work condition is burnt in shear layer of inlet and the end of down wall zone in straight segment

    對于壓力差很大的兩股氣流，所形成的壓縮波系的結構可以增加燃氣駐留時間，提高燃燒穩定性;為了提高擴散燃燒的效率，在保證能放熱的化學反應溫度范圍之內，應適當提高燃氣及空氣的來流入口溫度;燃氣噴嘴應居於燃燒室軸線上，是改進超音速燃燒室結構的一種思路。
  10. The dehydration time is square of the droplets diameter so the small diameters of the droplets can cut down the drying time then reduce the height of the drying chamber. to the combined spin - flow pressure spray drying, the diameters of droplets are small and the dehydration rate is higher so keeping the qualities of the dried products we can increase the speed of the inlet wind and reduce the temperature of the outlet wind thus can improve the evaporation intensity of the drying chamber and the average energy utilization of the drying equipment

    因霧滴的脫水時間與其直徑的平方成正比，減小液滴直徑有利於縮短乾燥脫水時間，可有效降低乾燥塔的高度；由於旋流式組合壓力噴嘴霧化滴徑的減小，脫水速度明顯加快，在不影響乾燥物料性質的前提下，適當提高進風溫度，同時有效地降低排氣溫度，有利於提高幹燥塔的蒸發強度，也有利於提高幹燥設備的平均能源利用率。
  11. It was found that the ultra - fine powder can flow smoothly in a spouted bed with a draft tube under some sorts of design parameter and operating condition, thus a new effective method to improve fluidization quality of the ultra - fine powders is obtained ; at higher supplied gas velocity, an increase in the solid circulation rate is observed ; the extent of the distance between the nozzle and the draft tube inlet result in the promotion of the solid circulation rate ; the solid circulation rate increase with increasing the draft tube diameter or the bed mass ; the gas bypassing is nearly zero in the present work ; and the solid flow in the annulus is observed as a moving bed

    結果表明：在一定的床層結構和操作條件下，超細粉可以在導向管噴動床中實現平穩流化，從而為改善超細粉的流化質量提供了一種有效的新方法；固體循環速率與噴動氣流量、導向管直徑、導向管底部與噴嘴出口間距以及床層裝填量成正比；氣體則基本上不存在「旁路」現象；環隙區中的顆粒流動表現為一移動床特徵。
  12. Longradar offer approximate ten thousand of products of pressure, vacuum, flow, air velocity, temperature, humidity, level and valves, which are commonly applied in the fields of industrial automation, hvac, building autoimmunization control, electric power, petroleum, chemical industry, boilers, water treatment, compressors, freezing refrigeration, food brewage, pharmacy, light industrial, environmsent protec - tion, clean industry etc

    在上游安裝一個帶有蛋形格柵的橢圓形流體噴嘴，可以提供一個精確構造簡單的空氣體積測量系統。在噴嘴的出口，空氣釋放時的風速分配是一致的靜壓為零。因此，噴嘴上游的總壓力是噴嘴出的速度壓力-於是就容易計算體積了。
  13. In other instruments, the stream is accelerated through a venturi or nozzle

    在其他儀器中，液體流則是通過文氏管或噴嘴加速的。
  14. A very special rotating cavity with micro - turbine ( de - swirl nozzles ) was applied to investigate the flow characteristics inside the cavity under three mid rotating speeds

    摘要通過實驗對中等轉速下帶有微型渦輪（反預旋噴嘴）的旋轉渦輪盤腔內流動特性進行了系統研究。
  15. Abstract : this paper introduce the basic theory of the hot - wire / film anemometer and the method to determine the flow velocity of calibration nozzle system. this calibration nozzle system is designed for the calibration of hot - wire / film anemometer. a method to determine the uncertainty of this system is fully analyzed using uncertainty thoery in this paper

    文摘:介紹了熱線熱膜流速儀的基本原理和用於熱線熱膜流速儀校準用的校準噴嘴系統的氣體速度確定方法，分析和推導了用不確定度理論全面分析系統不確定度的方法。
  16. 3. testing all the hydraulic parameters of the sprinkler installed with adjuster such as working pressure, water flux, the range of the sprinkler, intensity of water drop impact, characteristic of water distribution, etc. according to the testing data, we can learn the quantitative relations among the structure of the adjuster, working pressure, diameter of the nozzle, elevation of sprinkler, wind power, velocity of rotation and the range of water

    測試安裝「壓力調節器」后的噴頭的水力性能參數，即工作壓力、流量、射程、水滴的打擊強度、噴灑水分佈特性等。依據所測得的噴頭水力性能參數和射程數據，我們可較清楚的了解「壓力調節器」的結構形式、工作壓力、噴嘴直徑、噴射仰角、風力、旋轉速度和噴頭射程之間的定量關系。
  17. However, by comparison with flap nozzle servo valve which has been used widely and popularly by now, the torque motor of jet pipe servo valve has a larger rotary inertia. this causes low natural frequency of servo valve, and thus the response speed of jet pipe servo valve is slow. moreover, the jet pipe of servo valve has large flexibility, and it is easy to excite oscillations and noise in the valve, which is named self - excited oscillations and noise

    然而與目前普遍使用的噴嘴擋板伺服閥相比，射流管伺服閥的銜鐵組件轉動慣量大，導致力矩馬達部分固有頻率低，從而響應速度慢，此外，射流管供油管柔性大，容易產生自激現象，這些缺點都使得射流管伺服閥的動態特性差，從而影響了它的工作性能。
  18. The effects of particle type, liquid spraying rate, liquid concentration, fluidizing gas velocity, vibrated intensity, nozzle position and atomization air pressure on the growth of particles have been analyzed and discussed

    著重研究了晶種類別、料液流量、料液濃度、流化氣速、振動強度、噴嘴高度、霧化氣壓力等因素對顆粒成長的影響。
  19. Study on properties of grinding fluid jet and nozzle position limit during quick - point grinding

    快速點磨削磨削液射流特性及噴嘴極限位置研究
  20. The thruster contained a large - diameter, slowly rotating blade with nozzles that diffused the propulsive flow, minimizing the churning that would otherwise disturb the caked silt

    機器的推進器包含了大直徑慢速轉動的螺旋槳，而且推進水流由噴嘴送出，以避面劇烈攪動擾亂了結塊的淤泥。
分享友人
分享到 Line

分享到臉書