浸出方法 的英文怎麼說

中文拼音 [jìnchūfāngfǎ]
浸出方法 英文
leaching method
  • 浸 : Ⅰ動詞1 （泡在液體里） soak; steep; immerse 2 （液體滲入） soak; saturate; steep Ⅱ副詞[書面語] （...
  • 方 : Ⅰ名詞1 （方形; 方體） square 2 [數學] （乘方） involution; power 3 （方向） direction 4 （方面） ...
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 方法 : method; means; way; technique; process; procedure; plan; device; recipe; fashion; tool; maneuver
  1. The method of close water test has been used for a long time, so richer experience has been achieved. however, it not only takes pains and time, but also consumes raw materials during the close water test because of miscellaneous working procedures such as bricklaying in the two ends of pipe, water - repellent layer plastering, maintaining and water offletting, brick - block backouting after the test, especially in the region short of water and some drainage pipe with prop - pipe construction. in order to satisfy the fast development of municipal construction, new detection methods should be developed

    閉水試驗方法因其應用時間較長，目前已積累了較豐富的經驗，但在閉水試驗時，管道兩端砌築磚堵、抹防水層、養護、灌水浸泡，以及試驗后的放水、磚堵拆除等繁雜工序，不僅費工、費時，而且消耗原材料，尤其是在缺水的地區以及頂管施工的無壓管道，這些矛盾更加突出；因此，為滿足迅速發展的市政建設需要，有必要探索新的檢測方法，閉氣試驗就是其中一種，但是閉氣試驗目前還不完善，有待于進一步深入研究。
  2. First, a simple discussion for the mechanism about electrostatic atomization of the liquids has been given ; then the paper theoretically analyzed waving course, liquid drop producing course, and the liquid drop diffusing course in electrostatics atomization process., gave an analysis about the methods about carrying charges to the liquid drop, and analyzed that liquid with high electrical conductivity can be carried charges and atomized by electric field, while the isolated liquid with low electrical conductivity can be charged fully with the soakage electrode and inducing charge methods. at last the paper designed and configured the experimental equipment, conducted the atomization experiment to the three liquid medium - kerosene, emulsifier and alcohol under the same environment, handled the experimental results, then summarized the relationship between liquid electrostatic atomization effect and liquid surface tension, electronic conductivity and viscosity, along with the influence of voltage to electrostatic atomization and so on, found out the liquid atomization rule in high voltage electrostatic field

    首先，對液體介質的靜電霧化機理作了初步的探討，理論上分析了液體霧化過程中射流區、波紋區、霧滴區和霧滴擴散區;然後對液體荷電方法進行了研究分析，對于高電導率的液體，場致荷電和接觸荷電可以使其霧化，而對于電導率較低的絕緣液體，需用浸潤電極荷電和感應荷電方法使其充分帶電;最後，根據前面的研究分析，設計和組裝試驗裝置，在同一環境下對煤油、乳化劑、酒精三種不同液體介質進行高壓靜電霧化試驗，並對試驗結果進行分析處理，總結出液體靜電霧化與液體表面張力、電導率和粘度的關系及電壓對液體靜電霧化的影響等，得出高壓靜電場中液體霧化的一般規律。
  3. Determination of the rate aluminium oxide from kaolinite in coal measures

    煤系高嶺巖.三氧化二鋁浸出率測定方法
  4. The genomic dna are extracted from alcohol steep sample of tachinidae ( diptera ), by the analysis of experimental results, show that the method is feasible

    目的提出了一種有效的酒精浸泡的雙翅目寄蠅科昆蟲基因組dna的提取方法，通過對實驗結果的分析，表明該方法可行。
  5. Combining with practice of china ' s uranium ore heap leac hi ng, this paper proposes main ways and suitable technologies in the fields of emp hasizing feasib ility research, adop - ting strengthened technologies, improving equipment le vel, op timizing control technological factors and developing application range and so o n, which include adopting acid - curring and ferric sulphate - tric kle leaching process, bacteria heap leaching, countercurrent heap leaching, sele cting advanced material of heap bottom, developing large mechanized heap constru ction equipments and methods, popularizing drip i rrigation distributing solution, optimizing heap leaching process parameters, as we ll as developing recovery equipments suited to heap leaching, etc, in order to i n crease leaching rate, reduce heap leaching period and achieve more economic bene fits

    結合我國鈾礦堆浸實際，在重視堆浸可行性研究、採用強化堆浸技術、改進堆浸裝備水平、嚴格工藝條件及拓寬堆浸的應用范圍等方面提出一些有效途徑及適用技術，包括採用拌酸熟化-高鐵淋濾浸出、細菌堆浸、制粒堆浸、逆流堆浸，選用優質底墊層材料，研製大型機械化築堆方法和設備，推廣滴灌式布液，優化堆浸工藝參數，以及開發堆浸相配套的回收設備等，以提高浸出率、縮短堆浸周期，獲得更大的經濟效益。
  6. Some main results of testing research were as fellows : i. in the course of testing of leaching zinc dross, leaching zinc dross by sulfuric acid was researched and the effects on the leaching rate of the zinc dross were analyzed by author, the optimum conditions of leaching testing of zinc dross were determined as fellows : liquid - solid ratio 6 : 1, stirring ratio 250r / min, granularity 120 mesh, the soaking time 5h, the concentration of sulfuric acid of 30 %, and under these conditions, the rate of leaching zinc is above 92. 0 %. ii. in the course of testing of purification, on the basis of comprehending and comparing all present methods of the manganese - removal and iron - removal, the oxidizing method of manganese - removal in zinc sulfate solution using ammonium persulfate was put forward and the oxidizing method of iron - removal in zinc sulfate solution using the goethite process and oxidation - hydrolysis process was adopted

    研究的主要結果具體如下： 1 、研究了硫酸浸出鋅浮渣並分析了影響浸出率的各種因素，確定了浸出鋅浮渣的最佳條件為：液固比為6 ： 1 ，攪拌速度為250r min ，粒度為- 120目，酸浸時間為5 . 0h ，硫酸濃度30 ，鋅浮渣的浸出率大於92 . 0 ； 2 、在綜合和比較了目前除錳和除鐵的各種方法基礎上，提出了過硫酸銨氧化除錳方法和選擇了針鐵礦-氧化水解聯合法除鐵方法，並分析和討論了影響除錳率和除鐵率等各種因素，確定了除錳的條件為：溫度90 ， ph值5 . 4 ，反應時間3h ，過硫酸銨達到理論值的1 . 2倍，除錳率超過99 . 86 ；聯合法除鐵的條件為：氧化反應時間1 . 5小時、溫度控制在90 92 、 ph值5 . 2 5
  7. The control system of furnace " s temperature has been widely used in every walk of life, as an important link of repair and manufacture of the electrical equipment such as electromotor transformer etc., soaking lacquer drying craft has some especial requests on drying crafto this article starts with the analysis of drying chamber " s configuration, analyzed its configuration limitation and control function limitation according to the factory " s situation and advances the conception of heated air drying circulation, in addition, this article adopts an intellectualize a / d module, a development sampling tuning - voltage circuit, and presents the method to measure online the insulation resistance of products in order to improve constantly products quality

    而浸漆乾燥工藝作為電機、變壓器等電氣設備的修理、製造中的重要環節之一，對乾燥過程的質量要求有一定的特殊性。該文從乾燥爐的結構分析入手，聯繫到工廠的實際情況分析了結構功能缺陷和控制功能缺陷，提出了熱風循環乾燥的概念，同時，選擇了較為先進的a d板卡、熱電阻信號調理板等專業化智能卡，運用數字pid控制技術，構成了一個較有特色的計算機控制系統。此外，該文還從保證乾燥品質量的角度，採用智能化交流模塊和自製采樣調壓電路的方法，提出了在線檢測產修品的絕緣電阻的方法和手段，以確保企業產品質量不斷提高。
  8. Description of methods of lixiviant distribution for stope leaching

    原地爆破浸出工藝的布液方法綜述
  9. A number of conservation methods have been devised for waterlogged wood.

    已研究出許多種保養被水浸泡過的木頭的方法。
  10. The theoretic cycle capacity of limno2 is 286 mah g - 1, which has attracted a great deal of people to research. aim at the impurity of limno2 which was synthesized by the predecessor and the phase change during the electrochemical process, we try several methods, including wet moist chemical method, liquid state method, solide state method and liquid dipping method. at the same time, we study the synthesis of limnc > 2 in defferent atmosphere, for example air, argon and nitrogen

    Limno _ 2具有286mah ? g ~ （ - 1 ）的理論容量，這種高容量材料深受廣大研究者的關注，針對前人合成出的還有少量雜相和在電化學循環過程中出現相變四川人學碩l :學位論文的問題，我們嘗試了幾種合成方法:濕化學法、液相法、固相法和溶液浸漬法，並在不同氣氛:空氣、氮氣和氫氣中進行limnoz的合成研究。
  11. Chemical breath analyser - estimation of the alcohol impregnation by analysis of expelled air - specifications and test methods

    化學呼吸分析儀.對排出的空氣進行分析以估計乙醇浸透度.規范和試驗方法
  12. Class 1 electronic breath analyser - estimation of the alcohol impregnation by analysis of expelled air - specifications and test methods

    1級電子呼吸分析儀.對排出的空氣進行分析以估計乙醇浸透度.規范和試驗方法
  13. Class 2 electronic breath analyser - estimation of the alcohol impregnation by analysis of expelled air - specifications and test methods

    2級電子呼吸分析儀.對排出的空氣進行分析以估計乙醇浸透度.規范和試驗方法
  14. A sil flying head is designed to keep the distance between sil and recording medium in near - field range. a sil optical data storage system is built up when the recording head is combined with sil flying head. meanwhile, using astigmatic focusing error detection technology and twin optical pick - up heads, a novel nontouching nanometer measurement method is developed to measure the flying height of sil, and provides us with a powerful tool to optimize the design of sil fly head

    在sil存儲技術研究方面，首先提出一種光學玻璃熱熔加工製作sil的新方法，該方法克服了小半徑球透鏡加工的難題，成功製作出了半球固體浸沒透鏡；設計了sil飛行頭系統，並利用光學頭像散法聚焦誤差檢測原理，設計出一種雙光學頭sil飛行高度測量方案，實現了sil飛行頭飛行高度的測量。
  15. This paper, in the light of the special geological environment and actual project situation of the three gorges reservoir area, puts forward a comprehensive analysis and evaluation system suitable for the stability analysis of the bank landslide of the three gorges reservoir area under the premise of thorough consideration of the water influence on the stability of the bank landslide, and obtains the following achievements in several aspects that have the practical application significance and certain scientific research value : ( 1 ) it is discovered that the water activity is the primary factor of the formation of the new landslide and the revival of the ancient landslide. on the one hand, the rising underwater level reduces the actual stress of landslide ; on the other hand, the long time soaking of the underwater reduces the mechanics intensity of the landslide and the slide belt, both of which reduce directly the landslide stability ; ( 2 ) in view of the special condition of the three gorges reservoir area, this paper analyzes systematically the forces acted on the landslide of the three gorges reservoir area and the force varieties acted on the divided landslide when the water level changes between 175 meters and 145 meters. thus it is more scientific and comprehensive for the analysis of the forces acted on the landslide ; ( 3 ) this paper summaries systematically 10 kinds of typical computation projects by organic combinations of different kinds of situations in the dry season ( nature statue ), rainy season ( rainstorm or rains for a long time condition ), with 175m water level in the reservoir, during the earthquake, with the water level of the reservoir adjusted from 175m to 145m and so on, and produces

    本文針對長江三峽庫區特殊的地質環境與工程實際情況，在充分考慮水對庫岸滑體穩定性影響的前提下，提出了一個適用於長江三峽庫岸滑坡體穩定性分析的綜合分析評價體系，並取得了如下幾個方面具有工程實際意義和一定科學研究價值的研究成果： （ 1 ）研究結果發現，水的活動是新滑坡形成或古滑坡復活的主要因素，一方面是由於地下水位升高降低了滑坡體的有效應力，另一方面是由於地下水的長期浸泡降低滑體及滑帶的力學強度，這兩方面的因素均將直接降低滑坡的穩定性； （ 2 ）針對三峽庫區的特殊條件，系統分析了作用於三峽庫區滑坡體上的力系和庫水位在175m與145m間變化時滑體條塊的受力變化，從而使對作用於滑坡體上的力系分析更科學、更全面； （ 3 ）通過對滑體處于旱季（天然狀態） 、雨季（暴雨或長期降雨狀態） 、 175m庫水位、地震以及庫水位由175m調節下降至145m等各種不同情況的有機組合，本文系統地歸納總結出了10種典型計算工況，並具體給出了相應的作用荷載的計算方法，使在庫區岸坡滑體穩定性分析評價時對計算工況選擇及其作用荷載的計算更具規范性； （ 4 ）具體運用c + + builder開發了關于滑坡體穩定性綜合分析評價系統，使對滑坡體穩定性分析計算更方便、更準確； （ 5 ）將上述滑坡體穩定性綜合分析評價系統應用於重慶市豐都縣名山滑坡穩定性分析的具體事例中，分析結果表明，本文所提出滑坡體穩定性綜合分析評價方法對三峽庫區的滑坡穩定性分析是實用可行的。
  16. This paper is to study harmonic maps into symplectic groups and local isometric immersions into space forms by means of the soliton theory. by realizing an action of the rational loop group on the spaces of corrsponding solutions, we get the backlund transformation and the darboux transformation, and thereby we give the explicit construction for harmonic maps into symplectic groups and local isometric immersions into space forms via purely algebraic algorithm

    主要用孤立子理論研究到辛群的調和映射和到空間形式的局部等距浸入，通過有理loop群在其解空間上的dressing作用，給出b icklund變換和darboux變換的顯式表示，從而獲得到辛群及其對稱空間的調和映射和到空間形式的局部等距浸入的純代數構造方法。
  17. Method for the determination of water extract of tea for import and export

    進出口茶葉水浸出物測定方法
  18. Epa test method 1311 - 1, toxicity characteristic leaching procedure [ s ]

    固體廢物浸出毒性浸出方法-水平振蕩法[ s ]
  19. Test method standard for leaching toxicity of solid wastes - roll over leaching procedure

    固體廢物浸出毒性浸出方法翻轉法
  20. Test method standard for leaching toxicity of solid wastes - horizontal vibration extraction procedure

    固體廢物浸出毒性浸出方法水平振蕩法
分享友人
分享到 Line

分享到臉書