浸蝕間 的英文怎麼說

中文拼音 [jìnshíjiān]
浸蝕間 英文
etching room
  • 浸 : Ⅰ動詞1 （泡在液體里） soak; steep; immerse 2 （液體滲入） soak; saturate; steep Ⅱ副詞[書面語] （...
  • 蝕 : Ⅰ動詞1. （損失; 虧耗） lose 2. （腐蝕） erode; corrode Ⅱ名詞（天體現象） eclipse
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  1. The control system of mould level is crucial to improve the slab quality in the continuous casting process, pid controller is used in the traditional mould level control, and it has some defaults, such as : at the start - up or finishing period of casting or during the changeover of tundish, pid control has a bad effect, its overshoot is large and its transient time is long ; the erosion of the tundish stopper and the submersed nozzles lead to the accuracy of control become bad ; the abrupt falloff of block in the submersed nozzles makes the level acutely fluctuate, and pid control can not overcome the disturbances resulted from the change of casting speed

    結晶器液位控制系統是提高連鑄產品質量的關鍵環節，傳統的連鑄機液位控制方法採用常規的pid控制，存在如下不足：開始、結束澆注和換中間罐澆注時，控制效果差，超調量大，過渡時間長；塞棒頭和浸入式水口被腐蝕后引起控制精度差；浸入式水口堵塞物的突然脫落所引起的液位劇烈波動；無法克服拉速波動引起的擾動。
  2. It has low power and can defrost or heat in the refrigerator and expositing cabinet. both the ends of the heater adopt the imported resin glue and vulcanizate for seal ment and high ni - cr stainless steel as the case. it has good corrosive resisting performance and the insulation resistance is still more than 1000 after immersing in the water and being electrified for a long time

    本加熱器的特點為表面功率較小，在冰箱，展示櫃中起加熱化霜作用。電熱管兩端採用進口樹脂膠及硫化橡膠封口，外殼採用高鎳鉻不銹鋼，具有很好的耐腐蝕性能產品經長時間浸入水中通電試驗，其絕緣電阻仍1000m 。
  3. Hr - p196 is general purpose resins suitable for all kinds of glass reinforced moldings, it can be easily processed by hand lay - up with excellent impregnation of glass fibres and good mechanical strength

    Hr - p196耐腐蝕擠拉用樹脂hr p196是拉擠成型用間苯型聚酯樹脂，與玻纖浸潤性好。
  4. Because of the place obstruction of corrosion products in the surface of the alloys, while corrosion time is at 120 minutes above, the corrosion rate descends to the stable value in 48 hours

    當腐蝕浸泡的時間大於120分鐘后，腐蝕產物在鋁合金表面產生了明顯的位阻作用，從而使腐蝕速率逐漸下降，直至48小時后，腐蝕速率趨於一相對穩定的數值。
  5. Evaluating intergranular corrosion resistance of heat treatable aluminum alloys by immersion in sodium chloride hydrogen peroxide solution

    將鋁合金浸入氯化鈉和過氧化氫溶液中進行熱處理時抗晶粒間腐蝕的評定
  6. Testing the resistance of unalloyed and low alloy steels to intergranular stress corrosion cracking by attack of nitrate medium ; welded and unwelded materials

    非合金鋼和低合金鋼在受到硝酸鹽浸蝕作用時的耐晶間
  7. Standard guide for calculating and reporting measures of precision using data from interlaboratory wear or erosion tests

    用實驗室間磨損和浸蝕試驗數據計算和報告精密度的的標準指南
分享友人
分享到 Line

分享到臉書